RE: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr:0x44 not found for command
FYI. Using the later 3.6 releases and 3.7a I've found that I don't need any modprobe.conf settings to support the 150s or 500s. Just: modprobe tveeprom modprobe ivtv {I may still have the debug and tuner parms set, can't remember) -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Jim Reith Sent: Saturday, July 23, 2005 4:32 PM To: of my own; Discussion about mythtv Subject: Re: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr:0x44 not found for command >downloaded the correct firmware and fixed the module options, still the >same problem.. anymore idea? Thanks again. > >alias char-major-81 videodev >alias char-major-81-0 ivtv >alias char-major-81-1 ivtv >options cx25480 i2c_enable=1,1 >options saa7127 i2c_enable=-1,-1 HA! I see it... You have a typo in your options (if the above is correct) cx25480 != cx25840 subtle... > >ivtv: START INIT IVTV >ivtv: version 0.3.7 (a) loading >ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4 >ivtv: In case of problems please include the debug info >ivtv: between the START INIT IVTV and END INIT IVTV lines when >ivtv: mailing the ivtv-devel mailinglist. >ivtv: Autodetected WinTV PVR 150 card >ivtv: Found an iTVC16 based chip >ACPI: PCI interrupt :03:08.0[A] -> GSI 11 (level, low) -> IRQ 11 >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) >tveeprom: audio_processor = MSP3410D (type = 5) >ivtv: i2c attach [client=tveeprom[50],ok] >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 >ivtv: i2c attach [client=(tuner unset),ok] >cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) >cx25840: detecting cx25840 client on address 0x88 >cx25840: cx25843-23 found. Initializing... >cx25840: requesting /lib/modules/HcwMakoA.ROM >cx25840: firmware loaded >ivtv: i2c attach [client=cx25840[50],ok] >ivtv: i2c attach [client=wm8775[50],ok] >ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model >0x00914652, Revision 0x0001 >ivtv: NTSC tuner detected >ivtv: Radio detected >ivtv: Encoder revision: 0x02040011 >ivtv: Configuring WinTV PVR 150 card with 5 streams >ivtv: Registered v4l2 device for encoder MPEG minor 0 >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) >ivtv: Registered v4l2 device for encoder YUV minor 32 >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) >ivtv: Registered v4l2 device for encoder VBI minor 224 >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) >ivtv: Registered v4l2 device for encoder PCM audio minor 24 >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) >ivtv: Registered v4l2 device for encoder radio minor 64 >ivtv: Create encoder radio stream >ivtv: Setting Tuner 57 >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 >cx25840: decoder set norm NTSC >cx25840: decoder set input (6) >cx25840: now setting Tuner input >cx25840: set audio input (0) >ivtv: Switching standard to NTSC. >cx25840: decoder set norm NTSC >ivtv: Initialized WinTV PVR 150, card #0 >ivtv: Autodetected WinTV PVR 150 card >ivtv: Found an iTVC16 based chip >ACPI: PCI interrupt :03:09.0[A] -> GSI 10 (level, low) -> IRQ 10 >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) >tveeprom: audio_processor = MSP3410D (type = 5) >ivtv: i2c attach [client=tveeprom[50],ok] >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 >ivtv: i2c attach [client=(tuner unset),ok] >cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005) >ivtv: i2c attach [client=wm8775[50],ok] >ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model >0x00914652, Revision 0x0001 >ivtv: Radio detected >ivtv: ivtv_enc_thread: pid = 11202, itv = 0xe2230d20 >ivtv: ivtv_enc_vbi_thread: pid = 11203, itv = 0xe2230d20 >ivtv: Encoder revision: 0x02040011 >ivtv: Configuring WinTV PVR 150 card with 5 streams >ivtv: Registered v4l2 device for encoder MPEG minor 1 >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) >ivtv: Registered v4l2 device for encoder YUV minor 33 >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) >ivtv: Registered v4l2 device for encoder VBI minor 225 >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) >ivtv: Registered v4l2 device for encoder PCM audio minor 25 >iv
Re: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command
fixed modprobe.conf.. same problem.. it's weird that it detected it with the typo in the first place.. On 23 Jul 2005 13:31:33 -0700, Jim Reith <[EMAIL PROTECTED]> wrote: > >downloaded the correct firmware and fixed the module options, still > >the same problem.. anymore idea? Thanks again. > > > >alias char-major-81 videodev > >alias char-major-81-0 ivtv > >alias char-major-81-1 ivtv > >options cx25480 i2c_enable=1,1 > >options saa7127 i2c_enable=-1,-1 > > HA! I see it... You have a typo in your options (if the above is > correct) cx25480 != cx25840 > > subtle... > > > > >ivtv: START INIT IVTV > >ivtv: version 0.3.7 (a) loading > >ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4 > >ivtv: In case of problems please include the debug info > >ivtv: between the START INIT IVTV and END INIT IVTV lines when > >ivtv: mailing the ivtv-devel mailinglist. > >ivtv: Autodetected WinTV PVR 150 card > >ivtv: Found an iTVC16 based chip > >ACPI: PCI interrupt :03:08.0[A] -> GSI 11 (level, low) -> IRQ 11 > >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 > >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 > >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) > >tveeprom: audio_processor = MSP3410D (type = 5) > >ivtv: i2c attach [client=tveeprom[50],ok] > >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > >ivtv: i2c attach [client=(tuner unset),ok] > >cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) > >cx25840: detecting cx25840 client on address 0x88 > >cx25840: cx25843-23 found. Initializing... > >cx25840: requesting /lib/modules/HcwMakoA.ROM > >cx25840: firmware loaded > >ivtv: i2c attach [client=cx25840[50],ok] > >ivtv: i2c attach [client=wm8775[50],ok] > >ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model > >0x00914652, Revision 0x0001 > >ivtv: NTSC tuner detected > >ivtv: Radio detected > >ivtv: Encoder revision: 0x02040011 > >ivtv: Configuring WinTV PVR 150 card with 5 streams > >ivtv: Registered v4l2 device for encoder MPEG minor 0 > >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder YUV minor 32 > >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder VBI minor 224 > >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder PCM audio minor 24 > >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder radio minor 64 > >ivtv: Create encoder radio stream > >ivtv: Setting Tuner 57 > >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 > >cx25840: decoder set norm NTSC > >cx25840: decoder set input (6) > >cx25840: now setting Tuner input > >cx25840: set audio input (0) > >ivtv: Switching standard to NTSC. > >cx25840: decoder set norm NTSC > >ivtv: Initialized WinTV PVR 150, card #0 > >ivtv: Autodetected WinTV PVR 150 card > >ivtv: Found an iTVC16 based chip > >ACPI: PCI interrupt :03:09.0[A] -> GSI 10 (level, low) -> IRQ 10 > >ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 > >tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 > >tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > >tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) > >tveeprom: audio_processor = MSP3410D (type = 5) > >ivtv: i2c attach [client=tveeprom[50],ok] > >tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 > >ivtv: i2c attach [client=(tuner unset),ok] > >cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005) > >ivtv: i2c attach [client=wm8775[50],ok] > >ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model > >0x00914652, Revision 0x0001 > >ivtv: Radio detected > >ivtv: ivtv_enc_thread: pid = 11202, itv = 0xe2230d20 > >ivtv: ivtv_enc_vbi_thread: pid = 11203, itv = 0xe2230d20 > >ivtv: Encoder revision: 0x02040011 > >ivtv: Configuring WinTV PVR 150 card with 5 streams > >ivtv: Registered v4l2 device for encoder MPEG minor 1 > >ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder YUV minor 33 > >ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder VBI minor 225 > >ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder PCM audio minor 25 > >ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > >ivtv: Registered v4l2 device for encoder radio minor 65 > >ivtv: Create encoder radio stream > >ivtv: Setting Tuner 57 > >tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 > >ivtv: i2c client addr: 0x44 not found for command 0x40046403! > >ivtv: i2c client addr: 0x44 not found for command 0x40046404! > >ivtv: i2c client addr: 0x44 not found for comma
Re: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command
downloaded the correct firmware and fixed the module options, still the same problem.. anymore idea? Thanks again. alias char-major-81 videodev alias char-major-81-0 ivtv alias char-major-81-1 ivtv options cx25480 i2c_enable=1,1 options saa7127 i2c_enable=-1,-1 HA! I see it... You have a typo in your options (if the above is correct) cx25480 != cx25840 subtle... ivtv: START INIT IVTV ivtv: version 0.3.7 (a) loading ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt :03:08.0[A] -> GSI 11 (level, low) -> IRQ 11 ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25843-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model 0x00914652, Revision 0x0001 ivtv: NTSC tuner detected ivtv: Radio detected ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 64 ivtv: Create encoder radio stream ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 cx25840: decoder set norm NTSC cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to NTSC. cx25840: decoder set norm NTSC ivtv: Initialized WinTV PVR 150, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt :03:09.0[A] -> GSI 10 (level, low) -> IRQ 10 ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005) ivtv: i2c attach [client=wm8775[50],ok] ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model 0x00914652, Revision 0x0001 ivtv: Radio detected ivtv: ivtv_enc_thread: pid = 11202, itv = 0xe2230d20 ivtv: ivtv_enc_vbi_thread: pid = 11203, itv = 0xe2230d20 ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 1 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 33 ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 225 ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 25 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 65 ivtv: Create encoder radio stream ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: i2c client addr: 0x44 not found for command 0x40046403! ivtv: i2c client addr: 0x44 not found for command 0x40046404! ivtv: i2c client addr: 0x44 not found for command 0x4004646e! ivtv: Switching standard to NTSC. ivtv: i2c client addr: 0x44 not found for command 0x40046403! ivtv: Initialized WinTV PVR 150, card #1 ivtv: END INIT IVTV ivtv: ivtv_enc_thread: pid = 11315, itv = 0xe22542f4 ivtv: ivtv_enc_vbi_thread: pid = 11316, itv = 0xe22542f4 ivtv: Encoder revision: 0x02050032 ivtv: Encoder Firmware may be buggy, use version 0x02040011 Go here and get the correct firmwa
Re: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command
downloaded the correct firmware and fixed the module options, still the same problem.. anymore idea? Thanks again. alias char-major-81 videodev alias char-major-81-0 ivtv alias char-major-81-1 ivtv options cx25480 i2c_enable=1,1 options saa7127 i2c_enable=-1,-1 ivtv: START INIT IVTV ivtv: version 0.3.7 (a) loading ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4 ivtv: In case of problems please include the debug info ivtv: between the START INIT IVTV and END INIT IVTV lines when ivtv: mailing the ivtv-devel mailinglist. ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt :03:08.0[A] -> GSI 11 (level, low) -> IRQ 11 ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) cx25840: detecting cx25840 client on address 0x88 cx25840: cx25843-23 found. Initializing... cx25840: requesting /lib/modules/HcwMakoA.ROM cx25840: firmware loaded ivtv: i2c attach [client=cx25840[50],ok] ivtv: i2c attach [client=wm8775[50],ok] ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model 0x00914652, Revision 0x0001 ivtv: NTSC tuner detected ivtv: Radio detected ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 0 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 32 ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 224 ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 24 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 64 ivtv: Create encoder radio stream ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 cx25840: decoder set norm NTSC cx25840: decoder set input (6) cx25840: now setting Tuner input cx25840: set audio input (0) ivtv: Switching standard to NTSC. cx25840: decoder set norm NTSC ivtv: Initialized WinTV PVR 150, card #0 ivtv: Autodetected WinTV PVR 150 card ivtv: Found an iTVC16 based chip ACPI: PCI interrupt :03:09.0[A] -> GSI 10 (level, low) -> IRQ 10 ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) tveeprom: audio_processor = MSP3410D (type = 5) ivtv: i2c attach [client=tveeprom[50],ok] tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 ivtv: i2c attach [client=(tuner unset),ok] cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005) ivtv: i2c attach [client=wm8775[50],ok] ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model 0x00914652, Revision 0x0001 ivtv: Radio detected ivtv: ivtv_enc_thread: pid = 11202, itv = 0xe2230d20 ivtv: ivtv_enc_vbi_thread: pid = 11203, itv = 0xe2230d20 ivtv: Encoder revision: 0x02040011 ivtv: Configuring WinTV PVR 150 card with 5 streams ivtv: Registered v4l2 device for encoder MPEG minor 1 ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) ivtv: Registered v4l2 device for encoder YUV minor 33 ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) ivtv: Registered v4l2 device for encoder VBI minor 225 ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) ivtv: Registered v4l2 device for encoder PCM audio minor 25 ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) ivtv: Registered v4l2 device for encoder radio minor 65 ivtv: Create encoder radio stream ivtv: Setting Tuner 57 tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #1 ivtv: i2c client addr: 0x44 not found for command 0x40046403! ivtv: i2c client addr: 0x44 not found for command 0x40046404! ivtv: i2c client addr: 0x44 not found for command 0x4004646e! ivtv: Switching standard to NTSC. ivtv: i2c client addr: 0x44 not found for command 0x40046403! ivtv: Initialized WinTV PVR 150, card #1 ivtv: END INIT IVTV ivtv: ivtv_enc_thread: pid = 11315, itv = 0xe22542f4 ivtv: ivtv_enc_vbi_thread: pid = 11316, itv = 0xe22542f4 > ivtv: Encoder revision: 0x02050032 > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > > Go here and get the correct firmware > http://ivtv.writeme.ch/tiki-index.php?page=FirmwareVersions > > Then try again. I don't have a PVR
Re: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command
I am using the latest ivtv driver, tuner 0 loaded fine, works on myth, but tuner #1 gave the following error below, system is P4 1.8G running FC3, any idea? thanks. --- /etc/modprobe.conf alias char-major-81 videodev alias char-major-81-0 ivtv alias char-major-81-1 ivtv options cx25480 i2c_enable=-1,1,1 options saa7127 i2c_enable=1,-1,-1 These two i2c_enable lines are your problem if you ONLY have the 500 in the system. That setup is used for a 350/250 and a 500. I believe you simply want the lines to be the following for a 500 only system options cx25480 i2c_enable=1,1 options saa7127 i2c_enable=-1,-1 Jim (who had to deal with this type of stuff in my 350 & 150 system) ___ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users
RE: [mythtv-users] PVR500MCE tuner #1, ivtv: i2c client addr: 0x44 not found for command
> -Original Message- > From: [EMAIL PROTECTED] [mailto:mythtv-users- > [EMAIL PROTECTED] On Behalf Of of my own > Sent: Saturday, July 23, 2005 5:37 AM > To: mythtv-users@mythtv.org > Subject: [mythtv-users] PVR500MCE tuner #1,ivtv: i2c client addr: 0x44 not > found for command > > I am using the latest ivtv driver, tuner 0 loaded fine, works on myth, > but tuner #1 gave the following error below, system is P4 1.8G running > FC3, any idea? thanks. > > ivtv: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total) > ivtv: i2c client addr: 0x44 not found for command 0x40046466! > ivtv: Setup VBI API header 0xbd0d pkts 1 buffs 4 ln 24 sz 1456 > ivtv: Setup VBI start 0x002fea04 frames 4 fpi 1 lines 0x0140 > ivtv: i2c client addr: 0x44 not found for command 0x40046406! > ivtv: i2c client addr: 0x44 not found for command 0x40046406! > ivtv: No Free Mailbox for cmd 0x00c6 after 100 tries! > ivtv: Mailbox[0] 0x00dc flags 0x0003 > ivtv: Mailbox[1] 0x30c2 flags 0x30c2 > ivtv: Mailbox[2] 0x30c2 flags 0x30c2 > ivtv: Firmware UNRESPONSIVE when trying cmd 0x00c6!!! > > --- > /etc/modprobe.conf > alias char-major-81 videodev > alias char-major-81-0 ivtv > alias char-major-81-1 ivtv > options cx25480 i2c_enable=-1,1,1 > options saa7127 i2c_enable=1,-1,-1 > > - > ivtv: START INIT IVTV > ivtv: version 0.3.7 (a) loading > ivtv: Linux version: 2.6.11-1.35_FC3 686 REGPARM 4KSTACKS gcc-3.4 > ivtv: In case of problems please include the debug info > ivtv: between the START INIT IVTV and END INIT IVTV lines when > ivtv: mailing the ivtv-devel mailinglist. > ivtv: Autodetected WinTV PVR 150 card > ivtv: Found an iTVC16 based chip > ACPI: PCI interrupt :03:08.0[A] -> GSI 11 (level, low) -> IRQ 11 > ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 > tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 > tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) > tveeprom: audio_processor = MSP3410D (type = 5) > ivtv: i2c attach [client=tveeprom[50],ok] > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #0 > ivtv: i2c attach [client=(tuner unset),ok] > cx25840: starting probe on adapter ivtv i2c driver #0 (0x10005) > cx25840: detecting cx25840 client on address 0x88 > cx25840: cx25843-23 found. Initializing... > cx25840: requesting /lib/modules/HcwMakoA.ROM > cx25840: firmware loaded > ivtv: i2c attach [client=cx25840[50],ok] > ivtv: i2c attach [client=wm8775[50],ok] > ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model > 0x00914652, Revision 0x0001 > ivtv: NTSC tuner detected > ivtv: Radio detected > ivtv: Encoder revision: 0x02050032 > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > ivtv: Configuring WinTV PVR 150 card with 5 streams > ivtv: Registered v4l2 device for encoder MPEG minor 0 > ivtv: Create DMA encoder MPEG stream: 0 x 32768 buffers (0KB total) > ivtv: Registered v4l2 device for encoder YUV minor 32 > ivtv: Create DMA encoder YUV stream: 0 x 10800 buffers (0KB total) > ivtv: Registered v4l2 device for encoder VBI minor 224 > ivtv: Create DMA encoder VBI stream: 0 x 8736 buffers (0KB total) > ivtv: Registered v4l2 device for encoder PCM audio minor 24 > ivtv: Create DMA encoder PCM audio stream: 0 x 4608 buffers (0KB total) > ivtv: Registered v4l2 device for encoder radio minor 64 > ivtv: Create encoder radio stream > ivtv: Setting Tuner 57 > tuner: type set to 57 (Philips FQ1236A MK4) by ivtv i2c driver #0 > cx25840: decoder set norm NTSC > cx25840: decoder set input (6) > cx25840: now setting Tuner input > cx25840: set audio input (0) > ivtv: Switching standard to NTSC. > cx25840: decoder set norm NTSC > ivtv: Initialized WinTV PVR 150, card #0 > ivtv: Autodetected WinTV PVR 150 card > ivtv: Found an iTVC16 based chip > ACPI: PCI interrupt :03:09.0[A] -> GSI 10 (level, low) -> IRQ 10 > ivtv: XXX PCI device: 0x1a30 vendor: 0x8086 > tveeprom: Hauppauge: model = 23552, rev = D492, serial# = 8005926 > tveeprom: tuner = Philips FQ1236A MK4 (idx = 92, type = 57) > tveeprom: tuner fmt = NTSC(M) (eeprom = 0x08, v4l2 = 0x1000) > tveeprom: audio_processor = MSP3410D (type = 5) > ivtv: i2c attach [client=tveeprom[50],ok] > tuner: chip found at addr 0xc2 i2c-bus ivtv i2c driver #1 > ivtv: i2c attach [client=(tuner unset),ok] > cx25840: starting probe on adapter ivtv i2c driver #1 (0x10005) > ivtv: i2c attach [client=wm8775[50],ok] > ivtv: Tuner Type 57, Tuner formats 0x1000, Radio: yes, Model > 0x00914652, Revision 0x0001 > ivtv: Radio detected > ivtv: ivtv_enc_thread: pid = 5565, itv = 0xe2230d20 > ivtv: ivtv_enc_vbi_thread: pid = 5566, itv = 0xe2230d20 > ivtv: Encoder revision: 0x02050032 > ivtv: Encoder Firmware may be buggy, use version 0x02040011 > ivtv: Configuring WinTV PVR 150 card with 5 streams > ivtv: Registered v4l2 device