Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
Bill, A couple things... I just did a little checking... maybe this applies to your situation. I placed a long port... saved the schematic and then re-opened it and turned the OrCad ports option on. The port size changed to the OrCad size port(length 70). I closed the schematic(no save) and re-opened it... still OrCad size... Turned the option off... still OrCad size... Closed the Schematic and re-open it... back to normal(long port). Turn OrCad Ports back on and save schematic and repeat above and the size does NOT recover. When you turn the OrCad ports option off I did not see the ports change back immediately, to see the change you have to close the schematic(without saving it) and re-open it while the option is turned off... this will restore them to their original size. If you saved the schematic while the OrCad ports option was on, then I believe it also saved the ports at their current size, and they would have to be changed back manually. I hope this helps. If you saved it while the option was on... you may be able to get going from a back-up copy. -- Colby Siemer** Custom Battery Chargers ** Custom Power Supplies PowerStream Technology ** Custom UPS 140 S. Mountainway Drive ** Custom DC/DC Converters Orem Utah 84058 ** Power management electronics for OEMs http://www.PowerStream.com - Original Message - From: "Brooks,Bill" <[EMAIL PROTECTED]> To: "'Protel EDA Forum'" <[EMAIL PROTECTED]> Sent: Tuesday, April 17, 2001 12:43 PM Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 > Well, I uninstalled the protel software and re-installed from the CD and > updated to sp5 and the problem persists!!! It seems the software is changing > the length of the little boxes around the ports ... although I don't > understand how the re-installed software KNEW where the last file I had been > working on was!!! It obviously didn't uninstall everything!!! Otherwise it > would not have know where to look for the file... > Does this give anyone a clue as you what is going on? > Bill Brooks > PCB Design Engineer > DATRON WORLD COMMUNICATIONS INC. > 3030 Enterprise Court > Vista, CA 92083 > Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 > mailto:[EMAIL PROTECTED] > IPC Designers Council, San Diego Chapter > http://www.ipc.org/SanDiego/ > http://home.fda.net/bbrooks/pca/pca.htm > > > > -Original Message- > From: Isabelle BAUDRY [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, April 17, 2001 9:53 AM > To: Protel EDA Forum > Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 > > > Bill, > > The reason may be that you have selected "Orcad Ports" in the form > /Tools/Preferences/schematics by mistake. > > Isabelle Baudry > - CIRPACK - > 13 rue Salomon de Rothschild > F-92150 Suresnes > tel: +33 1 41 44 37 65 > fax: +33 1 41 44 37 61 > [EMAIL PROTECTED] > www.cirpack.com > > > -Message d'origine- > De : Brooks,Bill [mailto:[EMAIL PROTECTED]] > Envoy : mardi 17 avril 2001 18:18 > : 'Protel EDA Forum' > Objet : [PEDA] problem w/ ports on Protel Schematic Service pack 6 > > > Another weird problem > > I have a schematic that was edited by another user here that looks fine on > his machine... but when I pull it up the ports all change in length and are > not connected properly. Anyone seen this effect? Maybe I have some setting > that's wrong? or he does? can anyone clarify what's going on? I pull the > same file up in 98 and it looks fine!!! > Whets happening here? * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
Seems to not make a difference whether it's on when I open it or off. I tried going back a service pack level to sp5 and no change ... still messed up. hmmm... curious-er and curious-er... -Original Message- From: Abd ul-Rahman Lomax [mailto:[EMAIL PROTECTED]] Sent: Tuesday, April 17, 2001 10:20 AM To: Protel EDA Forum Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 At 09:18 AM 4/17/01 -0700, Brooks,Bill wrote: >I have a schematic that was edited by another user here that looks fine on >his machine... but when I pull it up the ports all change in length and are >not connected properly. Anyone seen this effect? Maybe I have some setting >that's wrong? or he does? can anyone clarify what's going on? I pull the >same file up in 98 and it looks fine!!! >Whets happening here? Probably Tools/Preferences/OrCAD_Ports is checked. When you load an OrCAD schematic, I think it is automatically set; and then it stays checked until you uncheck it. [EMAIL PROTECTED] Abdulrahman Lomax P.O. Box 690 El Verano, CA 95433 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
Well, I uninstalled the protel software and re-installed from the CD and updated to sp5 and the problem persists!!! It seems the software is changing the length of the little boxes around the ports ... although I don't understand how the re-installed software KNEW where the last file I had been working on was!!! It obviously didn't uninstall everything!!! Otherwise it would not have know where to look for the file... Does this give anyone a clue as you what is going on? Bill Brooks PCB Design Engineer DATRON WORLD COMMUNICATIONS INC. 3030 Enterprise Court Vista, CA 92083 Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 mailto:[EMAIL PROTECTED] IPC Designers Council, San Diego Chapter http://www.ipc.org/SanDiego/ http://home.fda.net/bbrooks/pca/pca.htm -Original Message- From: Isabelle BAUDRY [mailto:[EMAIL PROTECTED]] Sent: Tuesday, April 17, 2001 9:53 AM To: Protel EDA Forum Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 Bill, The reason may be that you have selected "Orcad Ports" in the form /Tools/Preferences/schematics by mistake. Isabelle Baudry - CIRPACK - 13 rue Salomon de Rothschild F-92150 Suresnes tel: +33 1 41 44 37 65 fax: +33 1 41 44 37 61 [EMAIL PROTECTED] www.cirpack.com -Message d'origine- De : Brooks,Bill [mailto:[EMAIL PROTECTED]] Envoy : mardi 17 avril 2001 18:18 : 'Protel EDA Forum' Objet : [PEDA] problem w/ ports on Protel Schematic Service pack 6 Another weird problem I have a schematic that was edited by another user here that looks fine on his machine... but when I pull it up the ports all change in length and are not connected properly. Anyone seen this effect? Maybe I have some setting that's wrong? or he does? can anyone clarify what's going on? I pull the same file up in 98 and it looks fine!!! Whets happening here? Bill Brooks PCB Design Engineer DATRON WORLD COMMUNICATIONS INC. 3030 Enterprise Court Vista, CA 92083 Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 mailto:[EMAIL PROTECTED] IPC Designers Council, San Diego Chapter http://www.ipc.org/SanDiego/ http://home.fda.net/bbrooks/pca/pca.htm * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
Thank you all !!! I did try this and discovered it as you say. Thank you for setting me straight!!! - Bill Brooks -Original Message- From: Colby - PowerStream [mailto:[EMAIL PROTECTED]] Sent: Tuesday, April 17, 2001 12:04 PM To: Protel EDA Forum Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 Bill, A couple things... I just did a little checking... maybe this applies to your situation. I placed a long port... saved the schematic and then re-opened it and turned the OrCad ports option on. The port size changed to the OrCad size port(length 70). I closed the schematic(no save) and re-opened it... still OrCad size... Turned the option off... still OrCad size... Closed the Schematic and re-open it... back to normal(long port). Turn OrCad Ports back on and save schematic and repeat above and the size does NOT recover. When you turn the OrCad ports option off I did not see the ports change back immediately, to see the change you have to close the schematic(without saving it) and re-open it while the option is turned off... this will restore them to their original size. If you saved the schematic while the OrCad ports option was on, then I believe it also saved the ports at their current size, and they would have to be changed back manually. I hope this helps. If you saved it while the option was on... you may be able to get going from a back-up copy. -- Colby Siemer** Custom Battery Chargers ** Custom Power Supplies PowerStream Technology ** Custom UPS 140 S. Mountainway Drive ** Custom DC/DC Converters Orem Utah 84058 ** Power management electronics for OEMs http://www.PowerStream.com - Original Message - From: "Brooks,Bill" <[EMAIL PROTECTED]> To: "'Protel EDA Forum'" <[EMAIL PROTECTED]> Sent: Tuesday, April 17, 2001 12:43 PM Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 > Well, I uninstalled the protel software and re-installed from the CD and > updated to sp5 and the problem persists!!! It seems the software is changing > the length of the little boxes around the ports ... although I don't > understand how the re-installed software KNEW where the last file I had been > working on was!!! It obviously didn't uninstall everything!!! Otherwise it > would not have know where to look for the file... > Does this give anyone a clue as you what is going on? > Bill Brooks > PCB Design Engineer > DATRON WORLD COMMUNICATIONS INC. > 3030 Enterprise Court > Vista, CA 92083 > Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 > mailto:[EMAIL PROTECTED] > IPC Designers Council, San Diego Chapter > http://www.ipc.org/SanDiego/ > http://home.fda.net/bbrooks/pca/pca.htm > > > > -Original Message- > From: Isabelle BAUDRY [mailto:[EMAIL PROTECTED]] > Sent: Tuesday, April 17, 2001 9:53 AM > To: Protel EDA Forum > Subject: Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6 > > > Bill, > > The reason may be that you have selected "Orcad Ports" in the form > /Tools/Preferences/schematics by mistake. > > Isabelle Baudry > - CIRPACK - > 13 rue Salomon de Rothschild > F-92150 Suresnes > tel: +33 1 41 44 37 65 > fax: +33 1 41 44 37 61 > [EMAIL PROTECTED] > www.cirpack.com > > > -Message d'origine- > De : Brooks,Bill [mailto:[EMAIL PROTECTED]] > Envoy : mardi 17 avril 2001 18:18 > : 'Protel EDA Forum' > Objet : [PEDA] problem w/ ports on Protel Schematic Service pack 6 > > > Another weird problem > > I have a schematic that was edited by another user here that looks fine on > his machine... but when I pull it up the ports all change in length and are > not connected properly. Anyone seen this effect? Maybe I have some setting > that's wrong? or he does? can anyone clarify what's going on? I pull the > same file up in 98 and it looks fine!!! > Whets happening here? * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
Watch out for the ORCAD port interpretation being clicked on under Tools/preferences. I have see this play with ports in this manner. Fabe -Original Message- From: Brooks,Bill [mailto:[EMAIL PROTECTED]] Sent: Tuesday, April 17, 2001 1:48 PM To: 'Protel EDA Forum' Subject: [PEDA] problem w/ ports on Protel Schematic Service pack 6 Another weird problem I have a schematic that was edited by another user here that looks fine on his machine... but when I pull it up the ports all change in length and are not connected properly. Anyone seen this effect? Maybe I have some setting that's wrong? or he does? can anyone clarify what's going on? I pull the same file up in 98 and it looks fine!!! Whets happening here? Bill Brooks PCB Design Engineer DATRON WORLD COMMUNICATIONS INC. 3030 Enterprise Court Vista, CA 92083 Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 mailto:[EMAIL PROTECTED] IPC Designers Council, San Diego Chapter http://www.ipc.org/SanDiego/ http://home.fda.net/bbrooks/pca/pca.htm * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
Bill, The reason may be that you have selected "Orcad Ports" in the form /Tools/Preferences/schematics by mistake. Isabelle Baudry - CIRPACK - 13 rue Salomon de Rothschild F-92150 Suresnes tel: +33 1 41 44 37 65 fax: +33 1 41 44 37 61 [EMAIL PROTECTED] www.cirpack.com -Message d'origine- De : Brooks,Bill [mailto:[EMAIL PROTECTED]] Envoy : mardi 17 avril 2001 18:18 : 'Protel EDA Forum' Objet : [PEDA] problem w/ ports on Protel Schematic Service pack 6 Another weird problem I have a schematic that was edited by another user here that looks fine on his machine... but when I pull it up the ports all change in length and are not connected properly. Anyone seen this effect? Maybe I have some setting that's wrong? or he does? can anyone clarify what's going on? I pull the same file up in 98 and it looks fine!!! Whets happening here? Bill Brooks PCB Design Engineer DATRON WORLD COMMUNICATIONS INC. 3030 Enterprise Court Vista, CA 92083 Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 mailto:[EMAIL PROTECTED] IPC Designers Council, San Diego Chapter http://www.ipc.org/SanDiego/ http://home.fda.net/bbrooks/pca/pca.htm * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
Re: [PEDA] problem w/ ports on Protel Schematic Service pack 6
At 09:18 AM 4/17/01 -0700, Brooks,Bill wrote: >I have a schematic that was edited by another user here that looks fine on >his machine... but when I pull it up the ports all change in length and are >not connected properly. Anyone seen this effect? Maybe I have some setting >that's wrong? or he does? can anyone clarify what's going on? I pull the >same file up in 98 and it looks fine!!! >Whets happening here? Probably Tools/Preferences/OrCAD_Ports is checked. When you load an OrCAD schematic, I think it is automatically set; and then it stays checked until you uncheck it. [EMAIL PROTECTED] Abdulrahman Lomax P.O. Box 690 El Verano, CA 95433 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
[PEDA] problem w/ ports on Protel Schematic Service pack 6
Another weird problem I have a schematic that was edited by another user here that looks fine on his machine... but when I pull it up the ports all change in length and are not connected properly. Anyone seen this effect? Maybe I have some setting that's wrong? or he does? can anyone clarify what's going on? I pull the same file up in 98 and it looks fine!!! Whets happening here? Bill Brooks PCB Design Engineer DATRON WORLD COMMUNICATIONS INC. 3030 Enterprise Court Vista, CA 92083 Tel: (760)597-1500 Ext 3772 Fax: (760)597-1510 mailto:[EMAIL PROTECTED] IPC Designers Council, San Diego Chapter http://www.ipc.org/SanDiego/ http://home.fda.net/bbrooks/pca/pca.htm * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To join or leave this list visit: * http://www.techservinc.com/protelusers/subscrib.html * - or email - * mailto:[EMAIL PROTECTED]?body=leave%20proteledaforum * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *