[Repeater-Builder] 7K to MastrII Repeater Backplane
Hello All, I'm about to install a 7K onto a MastrII repeater. I have found all of the points on the backplane that I need via the documentation at the Scom resource page "Interfacing a 7K to a GE MastrII." However, I'm at a loss for one point and do not see it on that resource page. I will be using a TS-64 through the 7K, not a factory Channel Guard Board. Where on the backplane can I inject the PL once it comes out of the 7K? Does "Channel Guard Input" appear on the backplane or must I run that wire up to the exciter? Any help would br greatly appreciated! Thanks Adam N2ACF Yahoo! Groups Links To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/ To unsubscribe from this group, send an email to:[EMAIL PROTECTED] Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
Re: [Repeater-Builder] 7K to MastrII Repeater Backplane
run that wire up to the exciter... if it is a duplexstation, run it to the black exciter plug on the door/drawer, and then to the appropriate pin on the exciter..if it's a transceive station combination, a wire may already be run from the receiver system board(where the cg board plugs in)to the exciter.. channel guard mod does not normally appear on the backplane. if a mobile conversion, look for a trace on the system board that connects to the cg mod pin on the exciter. it doesn't PL.. hi hi! :) Steve - Original Message - From: Adam C. Feuer To: Repeater-Builder@yahoogroups.com Cc: [EMAIL PROTECTED] Sent: Tuesday, September 21, 2004 7:51 PM Subject: [Repeater-Builder] 7K to MastrII Repeater Backplane Hello All, I'm about to install a 7K onto a MastrII repeater. I have found all of the points on the backplane that I need via the documentation at the Scom resource page "Interfacing a 7K to a GE MastrII." However, I'm at a loss for one point and do not see it on that resource page. I will be using a TS-64 through the 7K, not a factory Channel Guard Board. Where on the backplane can I inject the PL once it comes out of the 7K? Does "Channel Guard Input" appear on the backplane or must I run that wire up to the exciter? Any help would br greatly appreciated! Thanks Adam N2ACF Yahoo! Groups Links To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/ To unsubscribe from this group, send an email to:[EMAIL PROTECTED] Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
Re: [Repeater-Builder] 7K to MastrII Repeater Backplane
I'm am wondering ... where is the "backbone" for your system? I'm working on a simular one in southern West Virginia using a 900 mcs system. Ed - kb8qeu "Adam C. Feuer" wrote: Hello All,I'm about to install a 7K onto a MastrII repeater. I have found all of the points on the backplane that I need via the documentation at the Scom resource page "Interfacing a 7K to a GE MastrII." However, I'm at a loss for one point and do not see it on that resource page. I will be using a TS-64 through the 7K , not a factory Channel Guard Board.Where on the backplane can I inject the PL once it comes out of the 7K? Does "Channel Guard Input" appear on the backplane or must I run that wire up to the exciter?Any help would br greatly appreciated!ThanksAdam N2ACF Yahoo! Groups Links To visit your group on the web, go to:http://groups.yahoo.com/group/Repeater-Builder/ To unsubscribe from this group, send an email to:[EMAIL PROTECTED] Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.