Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
But is probably 20 uS..which would likely drop back to around 14 uS where the uS and PPM numbers are about the same. Ode At 12:25 PM 6/17/2009 -0500, you wrote: Plugging those numbers into my Excel Faraday calculator I get about 14ppm - not 20ppm. Dan On Wed, Jun 17, 2009 at 9:54 AM, Marshall Dudleymdud...@king-cart.com wrote: That may be true for batch processing, but for my flow system, the efficiency is about 1/4 of that. That is with stirring and polarity reversal. The exact stats are 1.5 gallon per hour, 20 mA and 20 ppm. This is probably due to the higher concentration tending to plate back out during the brewing. Marshall Dan Nave wrote: The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
With polarity shifting there are a few seconds per cycle that don't do much as the electrochemistry reverses. If I recall, the current stays constant, but the voltage makes a swing, so the EIS chemistry shifting may be delivering current like a battery for a few seconds. If the shift frequency is one minute, 10 or 20 seconds out of that cycle doing nearly nothing could make a huge error in the calculations. Ode At 09:44 PM 6/16/2009 -0500, you wrote: The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
That may be true for batch processing, but for my flow system, the efficiency is about 1/4 of that. That is with stirring and polarity reversal. The exact stats are 1.5 gallon per hour, 20 mA and 20 ppm. This is probably due to the higher concentration tending to plate back out during the brewing. Marshall Dan Nave wrote: The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
Marshall Dudley wrote: That may be true for batch processing, but for my flow system, the efficiency is about 1/4 of that. That is with stirring and polarity reversal. The exact stats are 1.5 gallon per hour, 20 mA and 20 ppm. This is probably due to the higher concentration tending to plate back out during the brewing. Sorry, there is a typo there. It should have been 80 mA, not 20. Marshall Marshall Dan Nave wrote: The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
Plugging those numbers into my Excel Faraday calculator I get about 14ppm - not 20ppm. Dan On Wed, Jun 17, 2009 at 9:54 AM, Marshall Dudleymdud...@king-cart.com wrote: That may be true for batch processing, but for my flow system, the efficiency is about 1/4 of that. That is with stirring and polarity reversal. The exact stats are 1.5 gallon per hour, 20 mA and 20 ppm. This is probably due to the higher concentration tending to plate back out during the brewing. Marshall Dan Nave wrote: The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
On the other hand, it is possible that any silver that collects on the negative electrode may require, after polarity has been switched, that the same amount of current be used to release it from the electrode as if it had been originally part of that electrode... Dan On Wed, Jun 17, 2009 at 12:19 PM, Marshall Dudleymdud...@king-cart.com wrote: Marshall Dudley wrote: That may be true for batch processing, but for my flow system, the efficiency is about 1/4 of that. That is with stirring and polarity reversal. The exact stats are 1.5 gallon per hour, 20 mA and 20 ppm. This is probably due to the higher concentration tending to plate back out during the brewing. Sorry, there is a typo there. It should have been 80 mA, not 20. Marshall Marshall Dan Nave wrote: The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
At 09:22 AM 6/15/2009 -0400, you wrote: My first question is, how long should I leave the process brewing and does it take longer if I am making 2 gallons at a time? do I ever need to get new silver leads and when should I? I just wiped my silver leads with a clean paper towel is that okay? how do I increase the ppm? after 3 hours what is the ppm? after 6 hours what is the ppm? and so on and so forth... feel free to call me now at my desk also with any helpful tips ## Too many glaring conditional vagaries to say anything at all. ..the questions are meaningless and un-answerable without a lot more information. Excepting the obvious: When the silver is gone, you don't have an electrode...time to get a new one. Anything clean is suitable for wiping one off. A. Evans/ Desk: 202.461.8863 Fax: 202.565.4679 Imagination is more important than knowledge. For knowledge is limited to all we now know and understand, while imagination embraces the entire world, and all there ever will be to know and understand. Subject: RE: CSShelf-life of CS I agree completely. I keep my homemade CS in a glass sun tea pitcher on the counter and it takes about a month for me and the fam to use 3/4 of it. I use the other 1/4 as a starter for my next batch. It has always stabilized at 5ppm. ## As measured by what method or instrument? Without splitting hairs ALL the way to the root, if a PPM/TDS meter was used, that's more like 10 PPM rather than 5. Meters don't measure PPM. PPM meters are designed to work in salt water. Silver water is not salt water. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
The point is, in this case, electrode size doesn't matter. If you are conducting at the rate of 1ma and the volume of water is 1 cup, then you release enough silver into the water in 1 hour hour to have an equivalent of 17 ppm. This gives you a rule by which you can get a ballpark idea of what may be going on in your brewing cell. You can use it to estimate. Just adjust for the variables. (For current values before you reach 1 ma, Hint: measure the current vs time and calculate an average.) I submit, that with polarity switching, the ppm of the product is exactly what is calculated by Faradays Law of Electrolysis. Until you have any fallout. And this is more accurate than measuring with a meter... Dan On Tue, Jun 16, 2009 at 5:32 AM, Ode Coyoteodecoy...@windstream.net wrote: At 12:56 PM 6/15/2009 -0500, you wrote: Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan ## Using how much electrode, at what distance and assuming that the first few hours were actually running at 1 milliamp when that's not very likely if the water is good. Ode -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
CSHow do I successfully create CS? Shelf-life of CS My very first Batch
My first question is, how long should I leave the process brewing and does it take longer if I am making 2 gallons at a time? do I ever need to get new silver leads and when should I? I just wiped my silver leads with a clean paper towel is that okay? how do I increase the ppm? after 3 hours what is the ppm? after 6 hours what is the ppm? and so on and so forth... feel free to call me now at my desk also with any helpful tips A. Evans/ Desk: 202.461.8863 Fax: 202.565.4679 Imagination is more important than knowledge. For knowledge is limited to all we now know and understand, while imagination embraces the entire world, and all there ever will be to know and understand. Albert Einstein 1879-1955, Physicist From: Scotty [mailto:scottie592...@yahoo.com] Sent: Thursday, May 28, 2009 10:24 AM To: silver-list@eskimo.com Subject: RE: CSShelf-life of CS I agree completely. I keep my homemade CS in a glass sun tea pitcher on the counter and it takes about a month for me and the fam to use 3/4 of it. I use the other 1/4 as a starter for my next batch. It has always stabilized at 5ppm. Scott With God, all things are possible. - Mark 10:27 --- On Wed, 5/27/09, Neville Munn one.red...@hotmail.com wrote: From: Neville Munn one.red...@hotmail.com Subject: RE: CSShelf-life of CS To: silver-list@eskimo.com Date: Wednesday, May 27, 2009, 7:25 PM Below are my rationalisations regarding some of your points raised. Your snipped quote: [cs does not have a long shelf life] and [always make it fresh... This might not be a creditable statement ] -Produced using appropriate methods and equipment it'll keep as long as I want. making it 'fresh' is credible if I want to ingest/apply predominantly ionic silver for a given circumstance, for another circumstance I may prefer a more even ratio of ions and particles present in which case I would wait 24-48 hours before ingesting/applying. [should be used up as soon as possible] -Only if I want to use a solution of high ionic silver content then I would only make small amounts to ensure it is consumed/used while awake. [The quality of the CS would also determine the shelf life] -Quality is Distilled Water and Pure Silver which should give mine unlimited shelf life. [how could you test it?] -Ignoring all the ballyhoo about meters, a meter will indicate when the solution has reached it's stabilizing point and readings should only fluctuate minimally from that point on...usually after 24-48 hours. [that it needs to be keep dark and probably a cool and dry place] -I made a 300ml glass four days ago to show someone and it's been sitting on the kitchen cupboard under 'flouro' lighting ever since and nothing has changed, still hovering around 19uS after stabilizing from an initial 27.3uS, and with the distinct 'sheen' to the solution, very faint 'colour' and fairly strong TE. Dunno if my rationalisations are of any help? N. _ Date: Wed, 27 May 2009 15:22:21 +0200 From: goldena...@gmail.com To: silver-list@eskimo.com Subject: CSShelf-life of CS I just read on that one german site for generators, that cs does not have a long shelf life, and then it should be used up as soon as possible, and that you should always make it fresh... This might not be a creditable statement on their part, as I've read no such thing anywhere, except of course, that it needs to be keep dark and probably a cool and dry place, like most other natural remedies. What would you guys say? The quality of the CS would also determine the shelf life, I would suppose. But again, how could you test it? Which generator had that feature again? I think it would be helpful to know what one produced... Aldona _ Find car news, reviews and more Looking to change your car this year? http://a.ninemsn.com.au/b.aspx?URL=http%3A%2F%2Fsecure%2Dau%2Eimrworldw ide%2Ecom%2Fcgi%2Dbin%2Fa%2Fci%5F450304%2Fet%5F2%2Fcg%5F801459%2Fpi%5F10 04813%2Fai%5F859641_t=762955845_r=tig_OCT07_m=EXT
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
It all depends on your generator. I have a Silver Puppy and I make up to 32 ounces at a time. The SP has a reverse polarity function which I use because you get almost no crud in the water but it takes longer to brew using this method. Mine takes approximately 9 to 10 hours to make this amount because my distilled water is extremely pure. The amount of TDS in the water reads 7-9 and I take this to mean there is approximately 14ppm at the end of the time. It is (almost) impossible to accurately judge the ppm but it doesn't really matter as long as it isn't over 30ppm (for normal use that is) dee ---Original Message--- From: Evans, Antonio F. Date: 15/06/2009 14:23:36 To: silver-list@eskimo.com Subject: CSHow do I successfully create CS? Shelf-life of CS My very first Batch My first question is, how long should I leave the process brewing and does it take longer if I am making 2 gallons at a time? do I ever need to get new silver leads and when should I? I just wiped my silver leads with a clean paper towel is that okay? how do I increase the ppm? after 3 hours what is the ppm? after 6 hours what is the ppm? and so on and so forth... feel free to call me now at my desk also with any helpful tips A. Evans/ Desk: 202.461.8863 faint_grain.jpg
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan On Mon, Jun 15, 2009 at 8:22 AM, Evans, Antonio F.antonio.ev...@va.gov wrote: My first question is, how long should I leave the process brewing and does it take longer if I am making 2 gallons at a time? do I ever need to get new silver leads and when should I? I just wiped my silver leads with a clean paper towel is that okay? how do I increase the ppm? after 3 hours what is the ppm? after 6 hours what is the ppm? and so on and so forth... feel free to call me now at my desk also with any helpful tips A. Evans/ Desk: 202.461.8863 Fax: 202.565.4679 Imagination is more important than knowledge. For knowledge is limited to all we now know and understand, while imagination embraces the entire world, and all there ever will be to know and understand. Albert Einstein 1879-1955, Physicist -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
Missed something... That is in a time period of 1 hour. Dan On Mon, Jun 15, 2009 at 12:54 PM, Dan Navebhangcha...@gmail.com wrote: Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current in 1 hour is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan On Mon, Jun 15, 2009 at 8:22 AM, Evans, Antonio F.antonio.ev...@va.gov wrote: My first question is, how long should I leave the process brewing and does it take longer if I am making 2 gallons at a time? do I ever need to get new silver leads and when should I? I just wiped my silver leads with a clean paper towel is that okay? how do I increase the ppm? after 3 hours what is the ppm? after 6 hours what is the ppm? and so on and so forth... feel free to call me now at my desk also with any helpful tips A. Evans/ Desk: 202.461.8863 Fax: 202.565.4679 Imagination is more important than knowledge. For knowledge is limited to all we now know and understand, while imagination embraces the entire world, and all there ever will be to know and understand. Albert Einstein 1879-1955, Physicist -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
RE: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
Thank you for the tip A. Evans/ Imagination is more important than knowledge. For knowledge is limited to all we now know and understand, while imagination embraces the entire world, and all there ever will be to know and understand. Albert Einstein 1879-1955, Physicist -Original Message- From: Dan Nave [mailto:bhangcha...@gmail.com] Sent: Monday, June 15, 2009 1:55 PM To: silver-list@eskimo.com Subject: Re: CSHow do I successfully create CS? Shelf-life of CS My very first Batch Two gallons is probably too much to brew at one time with most of the home generators we see. You would be better off starting out with a pint or a quart. (approx. 500 to 1000ml) My rule of thumb is that the maximum amount of silver released into 1 cup of water at 1 milliamp current is equivalent to approximately 17ppm. You can extrapolate from this rule. Just use your reasoning abilities, if you have any... (I assume you do) Dan On Mon, Jun 15, 2009 at 8:22 AM, Evans, Antonio F.antonio.ev...@va.gov wrote: My first question is, how long should I leave the process brewing and does it take longer if I am making 2 gallons at a time? do I ever need to get new silver leads and when should I? I just wiped my silver leads with a clean paper towel is that okay? how do I increase the ppm? after 3 hours what is the ppm? after 6 hours what is the ppm? and so on and so forth... feel free to call me now at my desk also with any helpful tips A. Evans/ Desk: 202.461.8863 Fax: 202.565.4679 Imagination is more important than knowledge. For knowledge is limited to all we now know and understand, while imagination embraces the entire world, and all there ever will be to know and understand. Albert Einstein 1879-1955, Physicist -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: silver-list@eskimo.com Address Off-Topic messages to: silver-off-topic-l...@eskimo.com The Silver List and Off Topic List archives are currently down... List maintainer: Mike Devour mdev...@eskimo.com
RE: CSHow do I successfully create CS? Shelf-life of CS My very first Batch
Could the folks that have their emails set for everyone to acknowledge the receipt of their message please change their settings? Samala, Renee ---Original Message--- Thank you for the tip
