subject:"\[Elphel\-support\] Elphel 353 server"

Re: [Elphel-support] Elphel 353 server

2017-02-10 Thread Daniel Rouan

Many thanks Oleg for your advices.

It works now with the sensor connected to J2.

The web server is now OK and I got images.

Finally it was indeed a question of cable and proper connection.

By the way the small plastic clip that presses the cable on the pins of the 
connector 
is broken and I replaced it by a piece of cardboard (rapped with several pieces 
of scotch
tape to reach the right thickness) inserted together with the cable end:  this 
may explain 
a previous bad connection.

regards,

   Daniel
 
Le 10 févr. 2017 à 15:14, Oleg  a écrit :

> Daniel,
> 
> So, your current connections are (10359 - mux board (its connectors are 
> marked as J1-4), 10353 - system board):
> 10359 J1 - 10353
> 10359 J2 - sensor
> 
> J1 is for the system board.
> One of the sensors sould always be connected to J2, so:
> * If the sensor is single it should go to J2.
> * If 2 sensors then J2 and J3 (or J2 and J4)
> 
> What's the firmware revision, btw - 8.2.16 ?
> 
> Try:
> 1. in telnet:
> mv /etc/autocampars.xml /etc/autocampars.xml_bkp
> sync
> reboot -f
> Check the 'dmesg' output.
> 
> This will generate a new configuration file. It could have been generated for 
> other connection scheme where no sensors were detected at the 1st boot after 
> firmware update.
> 
> 
> 2. If you connect the sensor directly to the system board and regenerate the 
> config file (as in 1.) - and the sensor gets detected - then you should be 
> able to get images. After 
>  
> Note:
> if the camera gets stuck at 'starting hardware sequencers', in telnet:
> killall -9 php
> There won't be images but the web server will work. 
>  
> Best regards,
> Oleg Dzhimiev
> Electronics Engineer
> phone: +1 801 783  x124
> Elphel, Inc.

___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Re: [Elphel-support] Elphel 353 server

2017-02-10 Thread Daniel Rouan

Oleg,

Sorry for the flood of messages…

Apparently I can send commands through the port 8081, such bimg, but for 
instance
the image returned is 1 px gif.  As if the sensor was not actually running.

Is there some command to make a deeper test ?

Daniel

Le 10 févr. 2017 à 13:36, Daniel Rouan  a écrit :

> Oleg,
> 
> Just after ending the previous email, I changed to the connector that  is the
> closest from the DC/DC converter FKC08-48. (silver box) and the msg returned
> by dmesg is changed : the sensor is found ! (see attached).
> 
> But, the browser (firefox) cannot connect anymore.
> 
> regards,
> 
>   Daniel
> 
>  
> 
>  
> Le 10 févr. 2017 à 13:15, Daniel Rouan  a écrit :
> 
>> Oleg,
>> 
>> I changed the cable with a spare one (for my application I had to buy longer
>> cables) but the result is the same.
>> 
>> By the way I'm doing the tests with one unique sensor (the other one is at 
>> another
>> place, far away) : is that a problem ? are the 3 connectors on the mux board 
>>  equivalent
>> to make the test ?
>> 
>> regards,
>> 
>>  Daniel
>> 
>>  
>> Le 9 févr. 2017 à 18:10, Oleg  a écrit :
>> 
>>> Daniel,
>>> 
>>> I see. Must be something wrong with either cables, sensor boards or a mux 
>>> board (but it was detected and programmed) - the boards are usually more 
>>> reliable than the cables.
>>> 
>>> If possible try to reconnect the long cables that connect the mux board 
>>> (0353-00-08) and sensors (0353-00-15) - see the 3D model (cables not shown).
>>> First try the sensor side then the mux side. 
>>> 
>>> If that doesn't work - you might have to send us the camera. Contact 
>>> sa...@elphel.com for details.
>>> 
>>> Best regards,
>>> Oleg Dzhimiev
>>> Electronics Engineer
>>> phone: +1 801 783  x124
>>> Elphel, Inc.
>> 
> 

___
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Re: [Elphel-support] Elphel 353 server

2017-02-10 Thread Daniel Rouan

Oleg,Just after ending the previous email, I changed to the connector that  is theclosest from the DC/DC converter FKC08-48. (silver box) and the msg returnedby dmesg is changed : the sensor is found ! (see attached).But, the browser (firefox) cannot connect anymore.regards,  Daniel {\rtf1\ansi\ansicpg1252\cocoartf1038
{\fonttbl\f0\fswiss\fcharset0 Helvetica;}
{\colortbl;\red255\green255\blue255;}
\paperw11900\paperh16840\margl1440\margr1440\vieww9000\viewh8400\viewkind0
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\ql\qnatural\pardirnatural

\f0\fs24 \cf0 Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release R64/1.64) #4 Thu Nov 4 20:21:16 MDT 2010\
Setting up paging and the MMU.\
On node 0 totalpages: 8192\
  DMA zone: 32 pages used for memmap\
  DMA zone: 0 pages reserved\
  DMA zone: 8160 pages, LIFO batch:0\
  Normal zone: 0 pages used for memmap\
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB\
Built 1 zonelists.  Total pages: 8160\
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2\
PID hash table entries: 256 (order: 8, 1024 bytes)\
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)\
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)\
Memory: 41376k/65536k available (1740k kernel code, 24160k reserved, 605k data, 72k init)\
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)\
Mount-cache hash table entries: 1024\
NET: Registered protocol family 16\
SCSI subsystem initialized\
usbcore: registered new interface driver usbfs\
usbcore: registered new interface driver hub\
usbcore: registered new device driver usb\
NET: Registered protocol family 2\
IP route cache hash table entries: 512 (order: -2, 2048 bytes)\
TCP established hash table entries: 2048 (order: 0, 8192 bytes)\
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)\
TCP: Hash tables configured (established 2048 bind 1024)\
TCP reno registered\
Check hardware configuration of Elphel 353 camera\
Elphel 10349/10369 IO extension board is not present\
fast_timer_init()\
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.\
io scheduler noop registered (default)\
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32\
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize\
PPP generic driver version 2.4.2\
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB\
eth0: changed MAC to 00:40:8C:CD:00:00\
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2\
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx\
ide: ETRAX FS built-in ATA DMA controller\
ide: Elphel 353 io extension board not found, skipping initialization\
Initializing USB Mass Storage driver...\
usbcore: registered new interface driver usb-storage\
USB Mass Storage support registered.\
usbcore: registered new interface driver usbserial\
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic\
usbcore: registered new interface driver usbserial_generic\
drivers/usb/serial/usb-serial.c: USB Serial Driver core\
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter\
usbcore: registered new interface driver belkin\
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2\
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101\
usbcore: registered new interface driver cp2101\
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07\
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty\
usbcore: registered new interface driver garmin_gps\
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28\
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232\
usbcore: registered new interface driver mct_u232\
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0\
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303\
usbcore: registered new interface driver pl2303\
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver\
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB\
stream co-processor: init done.\
axisflashmap: ...\
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)\
Additional Info: ID byte3=0x0, byte4=0x1d\
Bad block table found at page 65472, version 0x01\
Bad block table found at page 65408, version 0x01\
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x631\
NAND 128MiB 3,3V 8-bit: 0x0800 bytes of NAND flash memory.\
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.\
axisflashmap: flash read 512 bytes at 0x0004, data: 00 b0 05 f0 25 ff ed 9c\
axisflashmap: partition table offset 10, data: ef be 84 00 2d 0e 00 00\
axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a.\
offset

Re: [Elphel-support] Elphel 353 server

2017-02-09 Thread Daniel Rouan

Hello Oleg,

Sorry for the delay, but I was travelling.
I may had previously a problem with one of the two RJ45 cables. 
I succeed in having the solid orange and blinking green LEDs and
finally to telnet on 192.168.0.9

Here is the response to dmesg :

Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release 
R64/1.64) #4 Thu Nov 4 20:21:16 MDT 2010
Setting up paging and the MMU.
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 8160 pages, LIFO batch:0
  Normal zone: 0 pages used for memmap
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB
Built 1 zonelists.  Total pages: 8160
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)
Memory: 41376k/65536k available (1740k kernel code, 24160k reserved, 605k data, 
72k init)
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 1024
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -2, 2048 bytes)
TCP established hash table entries: 2048 (order: 0, 8192 bytes)
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Check hardware configuration of Elphel 353 camera
Elphel 10349/10369 IO extension board is not present
fast_timer_init()
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) 
is a CRISv32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB
eth0: changed MAC to 00:40:8C:CD:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide: ETRAX FS built-in ATA DMA controller
ide: Elphel 353 io extension board not found, skipping initialization
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / 
Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor 
driver v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS 
usb/tty
usbcore: registered new interface driver garmin_gps
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter 
driver z2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB
stream co-processor: init done.
axisflashmap: ...
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 
8-bit)
Additional Info: ID byte3=0x0, byte4=0x1d
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x631
NAND 128MiB 3,3V 8-bit: 0x0800 bytes of NAND flash memory.
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.
axisflashmap: flash read 512 bytes at 0x0004, data: 00 b0 05 f0 25 ff ed 9c
axisflashmap: partition table offset 10, data: ef be 84 00 2d 0e 00 00
axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a.
offset == 0x0004, size == 0x007C
offset == 0x0080, size == 0x0180
offset == 0x0200, size == 0x0500
offset == 0x0700, size == 0x00C0
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x-0x0800 : "main"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x-0x0004 : "part0"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x0004-0x0080 : "part1"

Re: [Elphel-support] Elphel 353 server

2017-02-09 Thread Daniel Rouan

Hello Oleg,

Sorry for the delay, but I was travelling.
I may had previously a problem with one of the two RJ45 cables. 
I succeed in having the solid orange and blinking green LEDs and
finally to telnet on 192.168.0.9

Here is the response to dmesg :

Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release 
R64/1.64) #4 Thu Nov 4 20:21:16 MDT 2010
Setting up paging and the MMU.
On node 0 totalpages: 8192
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 8160 pages, LIFO batch:0
  Normal zone: 0 pages used for memmap
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB
Built 1 zonelists.  Total pages: 8160
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2
PID hash table entries: 256 (order: 8, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)
Memory: 41376k/65536k available (1740k kernel code, 24160k reserved, 605k data, 
72k init)
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)
Mount-cache hash table entries: 1024
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -2, 2048 bytes)
TCP established hash table entries: 2048 (order: 0, 8192 bytes)
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
Check hardware configuration of Elphel 353 camera
Elphel 10349/10369 IO extension board is not present
fast_timer_init()
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
io scheduler noop registered (default)
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) 
is a CRISv32
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.2
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB
eth0: changed MAC to 00:40:8C:CD:00:00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
ide: ETRAX FS built-in ATA DMA controller
ide: Elphel 353 io extension board not found, skipping initialization
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / 
Peracom / GoHubs USB Serial Adapter
usbcore: registered new interface driver belkin
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor 
driver v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS 
usb/tty
usbcore: registered new interface driver garmin_gps
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232
usbcore: registered new interface driver mct_u232
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter 
driver z2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB
stream co-processor: init done.
axisflashmap: ...
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 
8-bit)
Additional Info: ID byte3=0x0, byte4=0x1d
Bad block table found at page 65472, version 0x01
Bad block table found at page 65408, version 0x01
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x631
NAND 128MiB 3,3V 8-bit: 0x0800 bytes of NAND flash memory.
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.
axisflashmap: flash read 512 bytes at 0x0004, data: 00 b0 05 f0 25 ff ed 9c
axisflashmap: partition table offset 10, data: ef be 84 00 2d 0e 00 00
axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a.
offset == 0x0004, size == 0x007C
offset == 0x0080, size == 0x0180
offset == 0x0200, size == 0x0500
offset == 0x0700, size == 0x00C0
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x-0x0800 : "main"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x-0x0004 : "part0"
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x0004-0x0080 : "part1"

Re: [Elphel-support] Elphel 353 server

Re: [Elphel-support] Elphel 353 server

Re: [Elphel-support] Elphel 353 server

Re: [Elphel-support] Elphel 353 server

Re: [Elphel-support] Elphel 353 server

5 matches

Site Navigation

Mail list logo

Footer information