Re: [Elphel-support] Elphel 353 server
Many thanks Oleg for your advices. It works now with the sensor connected to J2. The web server is now OK and I got images. Finally it was indeed a question of cable and proper connection. By the way the small plastic clip that presses the cable on the pins of the connector is broken and I replaced it by a piece of cardboard (rapped with several pieces of scotch tape to reach the right thickness) inserted together with the cable end: this may explain a previous bad connection. regards, Daniel Le 10 févr. 2017 à 15:14, Oleg a écrit : > Daniel, > > So, your current connections are (10359 - mux board (its connectors are > marked as J1-4), 10353 - system board): > 10359 J1 - 10353 > 10359 J2 - sensor > > J1 is for the system board. > One of the sensors sould always be connected to J2, so: > * If the sensor is single it should go to J2. > * If 2 sensors then J2 and J3 (or J2 and J4) > > What's the firmware revision, btw - 8.2.16 ? > > Try: > 1. in telnet: > mv /etc/autocampars.xml /etc/autocampars.xml_bkp > sync > reboot -f > Check the 'dmesg' output. > > This will generate a new configuration file. It could have been generated for > other connection scheme where no sensors were detected at the 1st boot after > firmware update. > > > 2. If you connect the sensor directly to the system board and regenerate the > config file (as in 1.) - and the sensor gets detected - then you should be > able to get images. After > > Note: > if the camera gets stuck at 'starting hardware sequencers', in telnet: > killall -9 php > There won't be images but the web server will work. > > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 x124 > Elphel, Inc. ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 353 server
Oleg, Sorry for the flood of messages… Apparently I can send commands through the port 8081, such bimg, but for instance the image returned is 1 px gif. As if the sensor was not actually running. Is there some command to make a deeper test ? Daniel Le 10 févr. 2017 à 13:36, Daniel Rouan a écrit : > Oleg, > > Just after ending the previous email, I changed to the connector that is the > closest from the DC/DC converter FKC08-48. (silver box) and the msg returned > by dmesg is changed : the sensor is found ! (see attached). > > But, the browser (firefox) cannot connect anymore. > > regards, > > Daniel > > > > > Le 10 févr. 2017 à 13:15, Daniel Rouan a écrit : > >> Oleg, >> >> I changed the cable with a spare one (for my application I had to buy longer >> cables) but the result is the same. >> >> By the way I'm doing the tests with one unique sensor (the other one is at >> another >> place, far away) : is that a problem ? are the 3 connectors on the mux board >> equivalent >> to make the test ? >> >> regards, >> >> Daniel >> >> >> Le 9 févr. 2017 à 18:10, Oleg a écrit : >> >>> Daniel, >>> >>> I see. Must be something wrong with either cables, sensor boards or a mux >>> board (but it was detected and programmed) - the boards are usually more >>> reliable than the cables. >>> >>> If possible try to reconnect the long cables that connect the mux board >>> (0353-00-08) and sensors (0353-00-15) - see the 3D model (cables not shown). >>> First try the sensor side then the mux side. >>> >>> If that doesn't work - you might have to send us the camera. Contact >>> sa...@elphel.com for details. >>> >>> Best regards, >>> Oleg Dzhimiev >>> Electronics Engineer >>> phone: +1 801 783 x124 >>> Elphel, Inc. >> > ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 353 server
Oleg,Just after ending the previous email, I changed to the connector that is theclosest from the DC/DC converter FKC08-48. (silver box) and the msg returnedby dmesg is changed : the sensor is found ! (see attached).But, the browser (firefox) cannot connect anymore.regards, Daniel {\rtf1\ansi\ansicpg1252\cocoartf1038
{\fonttbl\f0\fswiss\fcharset0 Helvetica;}
{\colortbl;\red255\green255\blue255;}
\paperw11900\paperh16840\margl1440\margr1440\vieww9000\viewh8400\viewkind0
\pard\tx566\tx1133\tx1700\tx2267\tx2834\tx3401\tx3968\tx4535\tx5102\tx5669\tx6236\tx6803\ql\qnatural\pardirnatural
\f0\fs24 \cf0 Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release R64/1.64) #4 Thu Nov 4 20:21:16 MDT 2010\
Setting up paging and the MMU.\
On node 0 totalpages: 8192\
DMA zone: 32 pages used for memmap\
DMA zone: 0 pages reserved\
DMA zone: 8160 pages, LIFO batch:0\
Normal zone: 0 pages used for memmap\
Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB\
Built 1 zonelists. Total pages: 8160\
Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2\
PID hash table entries: 256 (order: 8, 1024 bytes)\
Dentry cache hash table entries: 8192 (order: 2, 32768 bytes)\
Inode-cache hash table entries: 4096 (order: 1, 16384 bytes)\
Memory: 41376k/65536k available (1740k kernel code, 24160k reserved, 605k data, 72k init)\
Calibrating delay loop... 199.47 BogoMIPS (lpj=997376)\
Mount-cache hash table entries: 1024\
NET: Registered protocol family 16\
SCSI subsystem initialized\
usbcore: registered new interface driver usbfs\
usbcore: registered new interface driver hub\
usbcore: registered new device driver usb\
NET: Registered protocol family 2\
IP route cache hash table entries: 512 (order: -2, 2048 bytes)\
TCP established hash table entries: 2048 (order: 0, 8192 bytes)\
TCP bind hash table entries: 1024 (order: -1, 4096 bytes)\
TCP: Hash tables configured (established 2048 bind 1024)\
TCP reno registered\
Check hardware configuration of Elphel 353 camera\
Elphel 10349/10369 IO extension board is not present\
fast_timer_init()\
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.\
io scheduler noop registered (default)\
Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32\
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize\
PPP generic driver version 2.4.2\
ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB\
eth0: changed MAC to 00:40:8C:CD:00:00\
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2\
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx\
ide: ETRAX FS built-in ATA DMA controller\
ide: Elphel 353 io extension board not found, skipping initialization\
Initializing USB Mass Storage driver...\
usbcore: registered new interface driver usb-storage\
USB Mass Storage support registered.\
usbcore: registered new interface driver usbserial\
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic\
usbcore: registered new interface driver usbserial_generic\
drivers/usb/serial/usb-serial.c: USB Serial Driver core\
drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter\
usbcore: registered new interface driver belkin\
drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2\
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101\
usbcore: registered new interface driver cp2101\
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07\
drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty\
usbcore: registered new interface driver garmin_gps\
drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28\
drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232\
usbcore: registered new interface driver mct_u232\
drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0\
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303\
usbcore: registered new interface driver pl2303\
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver\
ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB\
stream co-processor: init done.\
axisflashmap: ...\
NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit)\
Additional Info: ID byte3=0x0, byte4=0x1d\
Bad block table found at page 65472, version 0x01\
Bad block table found at page 65408, version 0x01\
Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x631\
NAND 128MiB 3,3V 8-bit: 0x0800 bytes of NAND flash memory.\
axisflashmap: Set to boot from NAND flash, making NAND flash primary device.\
axisflashmap: flash read 512 bytes at 0x0004, data: 00 b0 05 f0 25 ff ed 9c\
axisflashmap: partition table offset 10, data: ef be 84 00 2d 0e 00 00\
axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a.\
offset
Re: [Elphel-support] Elphel 353 server
Oleg, I changed the cable with a spare one (for my application I had to buy longer cables) but the result is the same. By the way I'm doing the tests with one unique sensor (the other one is at another place, far away) : is that a problem ? are the 3 connectors on the mux board equivalent to make the test ? regards, Daniel Le 9 févr. 2017 à 18:10, Oleg a écrit : > Daniel, > > I see. Must be something wrong with either cables, sensor boards or a mux > board (but it was detected and programmed) - the boards are usually more > reliable than the cables. > > If possible try to reconnect the long cables that connect the mux board > (0353-00-08) and sensors (0353-00-15) - see the 3D model (cables not shown). > First try the sensor side then the mux side. > > If that doesn't work - you might have to send us the camera. Contact > sa...@elphel.com for details. > > Best regards, > Oleg Dzhimiev > Electronics Engineer > phone: +1 801 783 x124 > Elphel, Inc. ___ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
Re: [Elphel-support] Elphel 353 server
Hello Oleg, Sorry for the delay, but I was travelling. I may had previously a problem with one of the two RJ45 cables. I succeed in having the solid orange and blinking green LEDs and finally to telnet on 192.168.0.9 Here is the response to dmesg : Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release R64/1.64) #4 Thu Nov 4 20:21:16 MDT 2010 Setting up paging and the MMU. On node 0 totalpages: 8192 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 8160 pages, LIFO batch:0 Normal zone: 0 pages used for memmap Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB Built 1 zonelists. Total pages: 8160 Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 2, 32768 bytes) Inode-cache hash table entries: 4096 (order: 1, 16384 bytes) Memory: 41376k/65536k available (1740k kernel code, 24160k reserved, 605k data, 72k init) Calibrating delay loop... 199.47 BogoMIPS (lpj=997376) Mount-cache hash table entries: 1024 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -2, 2048 bytes) TCP established hash table entries: 2048 (order: 0, 8192 bytes) TCP bind hash table entries: 1024 (order: -1, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered Check hardware configuration of Elphel 353 camera Elphel 10349/10369 IO extension board is not present fast_timer_init() JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered (default) Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize PPP generic driver version 2.4.2 ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB eth0: changed MAC to 00:40:8C:CD:00:00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx ide: ETRAX FS built-in ATA DMA controller ide: Elphel 353 io extension board not found, skipping initialization Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter usbcore: registered new interface driver belkin drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2 drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101 usbcore: registered new interface driver cp2101 drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07 drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty usbcore: registered new interface driver garmin_gps drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28 drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232 usbcore: registered new interface driver mct_u232 drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0 drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB stream co-processor: init done. axisflashmap: ... NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Additional Info: ID byte3=0x0, byte4=0x1d Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x631 NAND 128MiB 3,3V 8-bit: 0x0800 bytes of NAND flash memory. axisflashmap: Set to boot from NAND flash, making NAND flash primary device. axisflashmap: flash read 512 bytes at 0x0004, data: 00 b0 05 f0 25 ff ed 9c axisflashmap: partition table offset 10, data: ef be 84 00 2d 0e 00 00 axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a. offset == 0x0004, size == 0x007C offset == 0x0080, size == 0x0180 offset == 0x0200, size == 0x0500 offset == 0x0700, size == 0x00C0 Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x-0x0800 : "main" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x-0x0004 : "part0" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x0004-0x0080 : "part1" Crea
Re: [Elphel-support] Elphel 353 server
Hello Oleg, Sorry for the delay, but I was travelling. I may had previously a problem with one of the two RJ45 cables. I succeed in having the solid orange and blinking green LEDs and finally to telnet on 192.168.0.9 Here is the response to dmesg : Linux version 2.6.19 (andrey@inspiron) (gcc version 3.2.1 Axis release R64/1.64) #4 Thu Nov 4 20:21:16 MDT 2010 Setting up paging and the MMU. On node 0 totalpages: 8192 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 8160 pages, LIFO batch:0 Normal zone: 0 pages used for memmap Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB Built 1 zonelists. Total pages: 8160 Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 2, 32768 bytes) Inode-cache hash table entries: 4096 (order: 1, 16384 bytes) Memory: 41376k/65536k available (1740k kernel code, 24160k reserved, 605k data, 72k init) Calibrating delay loop... 199.47 BogoMIPS (lpj=997376) Mount-cache hash table entries: 1024 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -2, 2048 bytes) TCP established hash table entries: 2048 (order: 0, 8192 bytes) TCP bind hash table entries: 1024 (order: -1, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered Check hardware configuration of Elphel 353 camera Elphel 10349/10369 IO extension board is not present fast_timer_init() JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered (default) Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize PPP generic driver version 2.4.2 ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB eth0: changed MAC to 00:40:8C:CD:00:00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx ide: ETRAX FS built-in ATA DMA controller ide: Elphel 353 io extension board not found, skipping initialization Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter usbcore: registered new interface driver belkin drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2 drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101 usbcore: registered new interface driver cp2101 drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07 drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty usbcore: registered new interface driver garmin_gps drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28 drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232 usbcore: registered new interface driver mct_u232 drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0 drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB stream co-processor: init done. axisflashmap: ... NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Additional Info: ID byte3=0x0, byte4=0x1d Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x631 NAND 128MiB 3,3V 8-bit: 0x0800 bytes of NAND flash memory. axisflashmap: Set to boot from NAND flash, making NAND flash primary device. axisflashmap: flash read 512 bytes at 0x0004, data: 00 b0 05 f0 25 ff ed 9c axisflashmap: partition table offset 10, data: ef be 84 00 2d 0e 00 00 axisflashmap: Found a valid partition table at 0xc02fd9ae-0xc02fda3a. offset == 0x0004, size == 0x007C offset == 0x0080, size == 0x0180 offset == 0x0200, size == 0x0500 offset == 0x0700, size == 0x00C0 Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x-0x0800 : "main" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x-0x0004 : "part0" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x0004-0x0080 : "part1" Crea
