Re: [SlimDevices: Unix] piCorePlayer 6.x.x - Bluetooth

2021-01-30 Thread tparvais 


Hello

I just finalized to upgrade to last PCP 7, last LMS, jivelite,...etc...
All is working perfect, thanks to the developpers

As I changed my smartphone from IOS =>Android Galaxy, no Airplay
possible anymore.
I wanted to use bluetooth to allow Android mobile to send music to
PCP/LMS

I insert a BT dongle laying around, install the libraries, apply last
patches. It seems to be properly detected. But impossible to pair with
my galaxy. This stupid phone asked for a PIN. I tried  or 1234
without success

same behavior with my laptop windows 10

any idea to debug ? 

Thomas

pCP Bluetooth extension build:0015
Starting BT Controller
Waiting for bluetooth controller.Ready
USB Bluetooth Hardware Address: 00:15:83:15:A2:2C
Starting pCP BT Pairing Agent
Powering on the BT controller
Success.
01-30 12:41 CET INFO Starting pCP BT Speaker Daemon
v7.0.0.0015
01-30 12:41 CET INFO Resetting asound.conf.
01-30 12:41 CET INFORemoving bt_ from asound.conf
01-30 12:41 CET INFO Config file: /usr/local/etc/pcp/pcp-bt.conf is
not found. Make sure to pair devices.
01-30 12:41 CET DEBUGPCM Devices found dbus.Dictionary({},
signature=dbus.Signature('oa{sv}'))
01-30 12:41 CET INFO Starting connection signal handlers.



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111972

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Wireless access point on piCorePlayer?

2020-12-16 Thread tparvais 


paul- wrote: 
> That output looks normal, but some wifi sticks do not support AP mode. 
> Unfortunately its hard to tell without doing alot of manual commands.
> 
> Try selecting a different channel and see if the AP comes up.   Do you
> have any other wifi sticks?

any idea of a wifi dongle that works fine in AP mode ?



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=108341

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Wireless access point on piCorePlayer?

2020-12-08 Thread tparvais 


Greg Erskine wrote: 
> Have you set the IP address properly for your network?
> 
> You shouldn't need to load anything manually. Running the original
> piCore wifi.sh is not a good idea.

yes I put 10.10.10.1

ideally i'd like to use bridge mode to reuse IP@ from my primary router
( but it does not workduring a test  on another PI3 (with wifi
embedded))

Wifi.sh was tested only to detect local wifi, I stopped CTLR-C before
running it completely



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=108341

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] PCP 6.1: squeezelite crashes regulary on PI3 (+LMS)

2020-12-07 Thread tparvais 


paul- wrote: 
> I would try Phillip44's "Reliable HTTP" Plugin.  Install it then make
> sure you enable it for the players you want.   This plugin will force
> proxied streaming, but has additional error handling to reopen streams
> if the remote disconnects the stream.

Hello

Thank you Paul

I activated "reliable" plugin from Philippe . I don't see specific
plugin  configuration except "activate" but nothing related for a
player. I presume there is nothing else to do ?

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=113142

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Wireless access point on piCorePlayer?

2020-12-07 Thread tparvais 


Hello

I want to activate Wifi AP capability of my Pi2b connected via Ethernet
UTP to enable better wifi coverage for remote control of PicorePlayer.

I plug the dongle and it seems to be properly detected:


Code:

DMESG
  [3.436577] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
  [3.585155] usb 1-1.3: New USB device found, idVendor=148f, 
idProduct=5370, bcdDevice= 1.01
  [3.585178] usb 1-1.3: New USB device strings: Mfr=1, Product=2, 
SerialNumber=3
  [3.585190] usb 1-1.3: Product: 802.11 n WLAN
  [3.585201] usb 1-1.3: Manufacturer: Ralink
  [3.585211] usb 1-1.3: SerialNumber: 1.0



in menu Wifi, I activated AP feature. When I start the stuff, I loose
the ethernet connection, so something goes wrong

AP Bridge: No
AC mode: No
IP address: 10.10.10.1


I was wondering if the dongle is properly configured: I installed
package wifi.tcz and when launching wifi.sh, it detects properly (but
with poor signal) my external wifi network.


Any idea on how to make this AP wifi running ?


Merci merci !

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=108341

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] PCP 6.1: squeezelite crashes regulary on PI3 (+LMS)

2020-11-23 Thread tparvais 


hello

I've still this buffering issue with this radio.

any other reco ? or log activate for better debugging ?

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=113142

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] PCP 6.1: squeezelite crashes regulary on PI3 (+LMS)

2020-10-30 Thread tparvais 


paul- wrote: 
> Internet radio is getting more and more difficult, as stations change
> things all the time.   
> 
> What I would try first is proxied streaming.   That would be set on the
> LMS setting page for that player.
> 
> Select the audio settings, then at the bottom, find the streaming
> method.  And set to proxied streaming.

ok, I found this parameter. I'll give it a try



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=113142

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] PCP 6.1: squeezelite crashes regulary on PI3 (+LMS)

2020-10-30 Thread tparvais 

paul- wrote: 
> Does it crash while playing, or when changing channels.  There are some
> ssl issues that we are aware of, but it just doesn’t play, it doesn’t
> crash.

i don't know when it crashes. Generally, this is discovered in the
morning when we want to power on the radio and the Jivelite screen show
the play is KO. 

IT shall crash during the day before as indicated by logs

only features remaing are to control others PICore (LMS still working
locally)

The Woman Acceptance Factor is decreasing a lot since few weeks, my wife
wants me to buy a FM Radio... ;-)


Thanks



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=113142

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] PCP 6.1: squeezelite crashes regulary on PI3 (+LMS)

2020-10-30 Thread tparvais 

paul- wrote: 
> Why did the time go backwards?   The first part was 11:05,  then 10:34?
> 
> Is it always the same URL that you are playing?  Can you confirm the
> URL’s?

I assume there is a day change between 11h05 (day before) and 10h34
(today, when I restart squeezelite)

I'm not playing always the same URL

If I want back in logs: radio was scdn.nrjaudio.fm:443


Code:


  [11:05:40.140763] set_volume:233 setting internal gain left: 142 right: 142
  [11:05:40.145721] process:521 strm
  [11:05:40.145819] process_strm:274 strm command s
  [11:05:40.145856] process_strm:344 strm s autostart: 3 transition period: 10 
transition type: 0 codec: m
  [11:05:40.145892] sendSTAT:189 STAT: STMf
  [11:05:40.146101] codec_open:264 codec open: 'm'
  [11:05:40.146307] _tcp_connect:486 connecting to 185.52.127.147:443
  [11:05:40.281049] stream_sock:576 header: GET 
/adwz2/fr/30001/mp3_128.mp3?origine=tune-in-radio HTTP/1.0
  Cache-Control: no-cache
  Connection: close
  Accept: */*
  Host: *scdn.nrjaudio.fm:443*
  User-Agent: iTunes/4.7.1 (Linux; N; piCore; armv8l-linux; FR; utf8) 
SqueezeCenter, Squeezebox Server, Logitech Media Server/7.9.3/1597753178
  Cookie: JSESSIONID=6C3A7EBC2955188EBC2F804F4EE56D93
  Cookie2: $Version="1"
  Icy-Metadata: 1
  
  
  [11:05:40.281162] sendSTAT:189 STAT: STMc
  [11:05:40.282244] process_strm:377 set fade mode: 0
  [11:05:40.282374] process:521 audg
  [11:05:40.282410] process_audg:433 audg gainL: 142 gainR: 142 adjust: 1
  [11:05:40.282440] set_volume:233 setting internal gain left: 142 right: 142
  [11:05:40.282533] process:521 strm
  [11:05:40.282565] process_strm:274 strm command t
  [11:05:40.282594] sendSTAT:189 STAT: STMt
  [11:05:40.345223] stream_thread:229 error reading headers: closed
  




then I suppose it crashes and when I restarted the squeezelite process,
it plays from 10h34


Code:

[10:34:28.113856] stream_sock:576 header: GET /laprem1ere-128.mp3 HTTP/1.0
  Cache-Control: no-cache
  Connection: close
  Accept: */*
  Host: *radios.rtbf.be:443*
  User-Agent: iTunes/4.7.1 (Linux; N; piCore; armv8l-linux; FR; utf8) 
SqueezeCenter, Squeezebox Server, Logitech Media Server/7.9.3/1597753178
  Icy-Metadata: 1
  
  
  [10:34:28.113970] sendSTAT:189 STAT: STMc
  [10:34:28.114119] process_strm:377 set fade mode



hope this helps

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=113142

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

[SlimDevices: Unix] PCP 6.1: squeezelite crashes regulary on PI3 (+LMS)

2020-10-30 Thread tparvais 

Hello

I have squeezelite process crashing often on one of my Pi + Hifiberry
AMP+

All the rest is still working (LMS, webserver..). I need to restart
squeezelite from the Web interface

some config info

PCPVERS="piCorePlayer 6.1.0"
WWW_BUILD: 0009
piCore version: 10.3pCP
10.3pCP
Squeezelite version and license: 1.9.7-1278-pCP


/usr/local/bin/squeezelite -n Living -o hw:CARD=sndrpihifiberry -a 80 4 
1 -b 4096 4096 -s 127.0.0.1 -d all debug -f /var/log/pcp_squeezelite.log
-v


and logs extract, not obvious for me


Code:


  
  ...
  [11:05:40.140726] process_audg:433 audg gainL: 142 gainR: 142 adjust: 1
  [11:05:40.140763] set_volume:233 setting internal gain left: 142 right: 142
  [11:05:40.145721] process:521 strm
  [11:05:40.145819] process_strm:274 strm command s
  [11:05:40.145856] process_strm:344 strm s autostart: 3 transition period: 10 
transition type: 0 codec: m
  [11:05:40.145892] sendSTAT:189 STAT: STMf
  [11:05:40.146101] codec_open:264 codec open: 'm'
  [11:05:40.146307] _tcp_connect:486 connecting to 185.52.127.147:443
  [11:05:40.281049] stream_sock:576 header: GET 
/adwz2/fr/30001/mp3_128.mp3?origine=tune-in-radio HTTP/1.0
  Cache-Control: no-cache
  Connection: close
  Accept: */*
  Host: scdn.nrjaudio.fm:443
  User-Agent: iTunes/4.7.1 (Linux; N; piCore; armv8l-linux; FR; utf8) 
SqueezeCenter, Squeezebox Server, Logitech Media Server/7.9.3/1597753178
  Cookie: JSESSIONID=6C3A7EBC2955188EBC2F804F4EE56D93
  Cookie2: $Version="1"
  Icy-Metadata: 1
  
  
  [11:05:40.281162] sendSTAT:189 STAT: STMc
  [11:05:40.282244] process_strm:377 set fade mode: 0
  [11:05:40.282374] process:521 audg
  [11:05:40.282410] process_audg:433 audg gainL: 142 gainR: 142 adjust: 1
  [11:05:40.282440] set_volume:233 setting internal gain left: 142 right: 142
  [11:05:40.282533] process:521 strm
  [11:05:40.282565] process_strm:274 strm command t
  [11:05:40.282594] sendSTAT:189 STAT: STMt
  [11:05:40.345223] stream_thread:229 error reading headers: closed
  
  /usr/local/bin/squeezelite -n Living -o hw:CARD=sndrpihifiberry -a 80:4::1 -b 
4096:4096 -s 127.0.0.1 -d all=debug -f /var/log/pcp_squeezelite.log -v 
  [10:34:14.579690] stream_init:370 init stream
  [10:34:14.579962] stream_init:371 streambuf size: 4194304
  [10:34:14.593171] output_init_alsa:940 init output
  [10:34:14.593313] output_init_alsa:980 requested alsa_buffer: 80 alsa_period: 
4 format: any mmap: 1
  [10:34:14.593410] output_init_common:350 outputbuf size: 4194304
  [10:34:14.593623] output_init_common:374 idle timeout: 0
  [10:34:14.601270] output_init_common:422 supported rates: 48000 44100 32000 
16000 11025 8000 
  [10:34:14.620451] output_init_alsa:1006 memory locked
  [10:34:14.620630] output_init_alsa:1012 glibc detected using mallopt
  [10:34:14.621280] output_thread:687 open output device: 
hw:CARD=sndrpihifiberry
  [10:34:14.621353] output_init_alsa:1032 set output sched fifo rt: 45
  [10:34:14.621393] alsa_open:351 opening device at: 44100
  [10:34:14.623054] alsa_open:422 opened device hw:CARD=sndrpihifiberry using 
format: S32_LE sample rate: 44100 mmap: 1
  [10:34:14.623238] alsa_open:513 buffer: 80 period: 4 -> buffer size: 3528 
period size: 882
  [10:34:14.624491] output_vis_init:162 opened visulizer shared memory as 
/squeezelite-00:0f:00:5a:4c:74
  [10:34:14.624550] decode_init:153 init decode
  [10:34:14.625319] register_dsd:908 using dsd to decode dsf,dff
  [10:34:14.670915] load_ff:685 loaded libavcodec.so.57 (57.48.101)
  [10:34:14.671045] load_ff:702 loaded libavformat.so.57 (57.41.100)
  [10:34:14.671095] load_ff:716 loaded libavutil.so.55 (55.28.100)
  [10:34:14.671510] register_ff:795 using ffmpeg to decode alc
  [10:34:14.671564] register_ff:779 using ffmpeg to decode wma,wmap
  [10:34:14.672968] load_faad:633 loaded libfaad.so.2
  [10:34:14.673033] register_faad:663 using faad to decode aac
  [10:34:14.675005] load_vorbis:351 loaded libvorbisfile.so.3
  [10:34:14.675071] register_vorbis:380 using vorbis to decode ogg
  [10:34:14.677304] load_opus:294 loaded libopusfile.so.0
  [10:34:14.677371] register_opus:324 using opus to decode ops
  [10:34:14.678807] load_flac:304 loaded libFLAC.so.8
  [10:34:14.678861] register_flac:332 using flac to decode ogf,flc
  [10:34:14.678889] register_pcm:483 using pcm to decode aif,pcm
  [10:34:14.680391] load_mad:388 loaded libmad.so.0
  [10:34:14.680470] register_mad:417 using mad to decode mp3
  [10:34:14.680499] decode_init:194 include codecs:  exclude codecs: 
  [10:34:14.681531] slimproto:887 connecting to 127.0.0.1:3483
  [10:34:14.682093] slimproto:926 connected
  [10:34:14.682164] slimproto:937 local player
  [10:34:14.682207] sendHELO:142 mac: 00:0f:00:5a:4c:74
  [10:34:14.682241] sendHELO:144 cap: 
CanHTTPS=1,Model=squeezelite,AccuratePlayPoints=1,HasDigitalOut=1,HasPolarityInversion=1,Firmware=v1.9.7-1278-pCP,ModelName=SqueezeLite,MaxSampleRate=48000,dsf,dff,alc,wma,wmap,aac,ogg,ops,ogf,flc,aif,pcm,mp3,loc
  [10:34:14.712792] process:521

Re: [SlimDevices: Unix] ANNOUNCE: piCorePlayer 6.0.0

2020-09-06 Thread tparvais 

paul- wrote: 
> How many image files are there?   You can’t add to the extension, but
> you could creat a new extension with the files.   Or if there are only a
> few, you can add them to the file system, then back them up by adding
> the files to /opt/.filetool.lst

Hello only few images . 

You propose to add these files in filetool ? But which full path should
I use to point to proper lms server html folder ?



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111787

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] ANNOUNCE: piCorePlayer 6.0.0

2020-09-05 Thread tparvais 

Hello
I'm running LMS on PCP 6.1.
Slimserver prefs/cache are on USB-HDD.

I update my favorites.opml in prefs directory

I want to use radio icons saved in LMS HTML directory but as it is
mapped to /tmp/tcloop/slimserver/usr/local/ and is read only, I
cannot make it permanent.

where should I put images files to make it reliable after reboot ? (and
available via LMS server). 

https://radios.rtbf.be/vivabxl-128.mp3;
icon="html/images/vivacite.png" text="Vivacité" type="audio" />

I could point to external www server, but I want to remain on my PCP

Thank you

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111787

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

[SlimDevices: Unix] picoreplayer: how to configure ethernet port 10M autonego off full duplex ?

2020-07-04 Thread tparvais 


Hello

For one Pi1 behind 30m UTP5e cable, I have some ethernet interface
instabilities: pi does not find the network.

I install ethtool

I want to run this command before network going up at boot sequence:
where should I add this command ?

sudo ethtool -s eth0 speed 10 autoneg off duplex full

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=112534

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] ANNOUNCE: piCorePlayer 6.0.0

2020-03-21 Thread tparvais 


Hello

I've upgraded from PCP6b7 to official 6 release.

I had to recalibrate my Waveshare 5'' for Jivelite.

When launching manually Jivelite, it works fine

When activating autostart, it does not work: it boots properly, then
after acquiring IP@ and probably launching jivelite from the default
script, I loose everything. I cannot even connect via SSH or Web.

I cannot find anymore /home/tc/www/cgi-bin/pcp_startup.sh to evaluate
and check its content. probably a problem there ???

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111787

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-02-01 Thread tparvais 


No body an idea to dEbug based  on this log? 

Tx



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-20 Thread tparvais 


ralphy wrote: 
> It's easy and done.  I rebuilt the current libts in pcp 5.x and 6.x beta
> with debug enabled for the plugins.  I have not tested it but the size
> of the plugins are much larger than the non debug extension.
> 

Whooh amazing! thanks !

I obtain the following when doing a calibration.

It skips the Bottom-Right calibration step on the screen, despite the
fact that it displays it properly on the debug logs

> tc@piCorePlayer:/usr/local/bin$ sudo TSLIB_FBDEVICE=/dev/fb0
> TSLIB_TSDEVICE=/dev/input/event1 /usr/local/bin/ts_calibrate
> tslib 1.16+ / libts ABI version 0 (0x00)
> Release-Date: [unreleased]
> Host OS: Linux, trying to open /dev/input/event1
> Loading module input
> Loading module pthres (pmin=1)
> Loading module variance (delta=30)
> Loading module dejitter (delta=100)
> Loading module linear
> Linear calibration constants: 0 0 33554432 0 0 0 65536
> xres = 1024, yres = 600
> tslib input device: vendor 0xEEF product 0x5 version 0x110 on bus 0x3
> RAW-> 0 600 255 1579544428.624771
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 1579544428.640763
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 30 600 255 1579544428.656760
> TS_READ_RAW> x = 30, y = 600, pressure = 255
> RAW-> 30 600 255 1579544428.656773
> TS_READ_RAW> x = 30, y = 600, pressure = 255
> RAW-> 0 0 0 1579544428.672761
> TS_READ_RAW> x = 0, y = 0, pressure = 0
> Took 4 samples...
> Top left : X =   15 Y =  600
> RAW-> 0 0 255 1579544428.688748
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 30 600 255 1579544428.704759
> TS_READ_RAW> x = 30, y = 600, pressure = 255
> RAW-> 0 600 255 1579544428.720755
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 1579544428.736750
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 30 600 255 1579544428.752756
> TS_READ_RAW> x = 30, y = 600, pressure = 255
> RAW-> 0 600 255 1579544428.768754
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 1579544428.784749
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 0 600 255 157958.704775
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 157958.720761
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 1017 600 255 157958.736768
> TS_READ_RAW> x = 1017, y = 600, pressure = 255
> RAW-> 1017 600 255 157958.736780
> TS_READ_RAW> x = 1017, y = 600, pressure = 255
> RAW-> 0 0 0 157958.752767
> TS_READ_RAW> x = 0, y = 0, pressure = 0
> Took 11 samples...
> Top right : X =0 Y =  600
> RAW-> 0 0 255 157958.768755
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 1017 600 255 157958.784760
> TS_READ_RAW> x = 1017, y = 600, pressure = 255
> RAW-> 1017 600 255 157958.784773
> TS_READ_RAW> x = 1017, y = 600, pressure = 255
> RAW-> 0 0 0 157958.800766
> TS_READ_RAW> x = 0, y = 0, pressure = 0
> Took 3 samples...
> Bot right : X = 1017 Y =  600
> RAW-> 0 0 255 157958.816757
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 1017 600 255 157958.832761
> TS_READ_RAW> x = 1017, y = 600, pressure = 255
> RAW-> 0 600 255 157958.848761
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 157958.864754
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 1017 600 255 157958.880758
> TS_READ_RAW> x = 1017, y = 600, pressure = 255
> RAW-> 0 600 255 157958.896754
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 157958.912749
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 0 600 255 1579544476.448768
> TS_READ_RAW> x = 0, y = 600, pressure = 255
> RAW-> 0 0 255 1579544476.464759
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 34 600 255 1579544476.480765
> TS_READ_RAW> x = 34, y = 600, pressure = 255
> RAW-> 34 600 255 1579544476.480779
> TS_READ_RAW> x = 34, y = 600, pressure = 255
> RAW-> 0 0 0 1579544476.496765
> TS_READ_RAW> x = 0, y = 0, pressure = 0
> Took 11 samples...
> Bot left : X =0 Y =  600
> RAW-> 0 0 255 1579544476.512755
> TS_READ_RAW> x = 0, y = 0, pressure = 255
> RAW-> 34 600 255 1579544476.528762
> TS_READ_RAW> x = 34, y = 600, pressure = 255
> RAW-> 0 600 255 1579544476.544759
> TS_READ_RAW> x = 0, y = 600, pressure = 255
>

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-19 Thread tparvais 


ralphy wrote: 
> It's already included in the libts extension.
> 
> You need to modify /usr/local/etc/ts.conf and add a line
> 
> module_raw waveshare
> 
> You will also likely need to make other changes to the ts.conf file but
> I can't really help you with that as I don't have that screen.
> 
> Backup the pcp config and reboot.
> 
> Here's the 'ts.conf man page'
> (https://manpages.debian.org/unstable/libts0/ts.conf.5.en.html)
> 
> The only bit of info I found on the waveshare modules was at the top of
> the source code.
> 
> > 
Code:

  >   > * Usage:
  > *   module_raw waveshare vid_pid=: len=
  > */

> > 
> 
> EDIT: Plus the info from the github site I referenced above.

Thank you for all that information.

I've tried with 


Code:

module_raw waveshare vid_pid=0eef:0005 len=25



no success: ts_calibrate didn"'t react to touch anymore

That's pitty that tslib and tools have not been compiled with DEBUG mode
available. Is that possible to compile this easily ? (never done it on
picoreplayer)

Very few means to debug currently

I'll keep working on it

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-18 Thread tparvais 


ralphy wrote: 
> That really sounds like you need to make changes to ts.conf for your
> touchscreen.
> 
> What variations did you try in the ts.conf file?
> 
> Did you try the waveshare driver that's included in the libts extension?
> It's based on the original driver from 
> https://github.com/derekhe/waveshare-7inch-touchscreen-driver and is for
> the waveshare 7" screen.


I was not aware of this driver. How can I load it on picoreplayer ? Is
it available on repository with tcz format ?

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-18 Thread tparvais 


ralphy wrote: 
> Good.  First let's go back and try using the libts extension from pcp
> 3.5 that was reported to work with the waveshare screen, albeit a
> different model.
> 
> You'll need to install the libcofi.tcz extension from the webgui as
> well, since the older libts requires it but the latest one does not.
> 
> https://forums.slimdevices.com/showthread.php?108852-Announce-piCorePlayer-3-5-0/page30
> 
> If the default ts.conf doesn't work, change it as described in 'post
> 294'
> (https://forums.slimdevices.com/showthread.php?108852-Announce-piCorePlayer-3-5-0=913574=1#post913574),
> save your configuration, reboot, confirm your ts.conf changes survived
> the reboot and try to calibrate again.
> 
> There is also a link to the documentation for the various libts modules
> that may help.
> 
> If this still doesn't work, I have one other libts extension we can try.

Hello

I strictly follow commands above.
Unfortunately, calibration process is still crazzy, same effect:
calibration steps for random corners are skipped , thus fails.

Thank you

Thomas

PS: I tried Max2play, and it works without calibration. I wanted to be
sure the screen is ok. But I don't wantto usemax2play, I prefer PC as
I've already several pi's with PC. Thanks



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-15 Thread tparvais 


ralphy wrote: 
> An older version of the libts extension might work.
> 
> What is the contents of your libts.tcz.md5.txt and does it checksum ok?
> 
> From an ssh login.  Commands are bold.
> > 
Code:

  >   > 
  > tc@rpi4:~$ *ceo*
  > tc@rpi4:/mnt/mmcblk0p2/tce/optional$ *cat libts.tcz.md5.txt*
  > d22140cf0d8bca2eeddcccae3d3159f7  libts.tcz
  > tc@rpi4:/mnt/mmcblk0p2/tce/optional$ *md5sum -c libts.tcz.md5.txt*
  > libts.tcz: OK
  > 

> > 

Hi

yes MD5 is correct and aligned with above.

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Touch off with Jivelite/Waveshare 5" on piCorePlayer

2020-01-12 Thread tparvais 


Hello

As I was not able to use my WaveShare 7'' 1024*600 with juvelite due to
calibration issue (I'll debug this later), I've used a Waveshare 5'' (B)
instead.

It works like a charm ! Very nice !

I build a small enclosure in wood, finished with bamboo sheet (as my
kitchen)

29017

Congrats to Picoreplayer & Jivelite authors !

Thomas


+---+
|Filename: jivelite.jpg |
|Download: http://forums.slimdevices.com/attachment.php?attachmentid=29017|
+---+


tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=109619

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Jivelite for piCorePlayer

2020-01-11 Thread tparvais 


ralphy wrote: 
> You can create a Favorite in LMS, then navigate to the Favorites menu
> item.  Unfortunately, the favorites editor doesn't provide a way to
> change the icon field. The only way I've found to use a custom icon in
> favorites is to shutdown LMS update the icon="html/images/radio.png"
> field in the favorites.opml with a URL to a web server with the icon
> file and start LMS again.
> 
> For example
> https://stream.885fm.org/1;
> icon="http://ralph-irving.users.sourceforge.net/images/socalfm88.png;
> text="88.5 FM Southern California" type="audio" />
> 
> You could have LMS serve the icon as well, by placing the custom icon at
> the same location as the default radio.png and just change the filename
> at the end of the icon field.


thanks, this works perfectly



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=103330

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Jivelite for piCorePlayer

2020-01-10 Thread tparvais 


Hello

I wanted to know if it is possible to add custom icon in jivelite menu
for direct access to some radio URL or Spotify playlist ?

Or should I use an external switch connected to GPIO and a hack (that I
don't know yet) to do this ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=103330

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-09 Thread tparvais 


ralphy wrote: 
> Hi Thomas,
> 
> I saw your post and as Paul stated we don't have the hardware so
> troubleshooting is near impossible.  We support the official rpi 7"
> touchscreen.
> Granted it's more expensive, but there are so many variations of the
> waveshare screens and most require different configurations to get
> working.

Hello

I understand well. I was looking for some ideas where to find/dig. I'm
pretty sure it's behind TS_LIB calibration.
PiCore TS_LIB tools version has been compiled with limited debug option.


I was ready to go further based on on our ideas where to investiguate.
Thank you

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-09 Thread tparvais 

paul- wrote: 
> Since none of us have the hardware, we can’t troubleshoot.   Have you
> tried the tstest stuff?   Looks like the screen is not giving you good
> values.  
> 
> Ralphy knows the tslib stuff better than most.

Weird that noboby tries this screen as waveshare is quite common for
touchscreen.

yes I tested ts_test but it does not work as the pointercal values are
NOK. the tool is displayed on the screen byt impossible to draw
anything.

I contacted Ralphy by PM, He's my last solution


Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-08 Thread tparvais 


paul- wrote: 
> Odd that you have 2 different input devices listed.   Have you tried
> /dev/input/event5

Hi

When I tried to use the other event (BYZHYYZHY By ZH851 Mouse), the
ts_calibrate does not react when I press the screen

I'm stuck...

Any idea where I can get support ? 

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

[SlimDevices: Unix] WaveShare 7'' touchescreen calibration issue with Jivelite

2020-01-06 Thread tparvais 


Hello


I've moved this message from an other thread to a new thread as this is
concerning 7'' screen waveshare.

I have the touchscreen 7'' Waveshare HDMI LCD (C) on a raspberrypi 3B
with PicorePlayer 5.0

I adapted pcp_startup.sh accordingly to use *BYZHYYZHY By ZH851
Touchscreen* as identifier.

I: Bus=0003 Vendor=0eef Product=0005 Version=0110
N: Name="BYZHYYZHY By ZH851 Mouse"
P: Phys=usb-3f98.usb-1.4/input0
S:
Sysfs=/devices/platform/soc/3f98.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:0EEF:0005.0004/input/input6
U: Uniq=c0U585P865
H: Handlers=mouse1 event5 js0
B: PROP=0
B: EV=1b
B: KEY=7 0 0 0 0 0 0 0 0
B: ABS=3
B: MSC=10

I: Bus=0003 Vendor=0eef Product=0005 Version=0110
N: Name="*BYZHYYZHY By ZH851 Touchscreen*"
P: Phys=usb-3f98.usb-1.4/input0
S:
Sysfs=/devices/platform/soc/3f98.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:0EEF:0005.0004/input/input7
U: Uniq=c0U585P865
H: Handlers=mouse2 *event6*
B: PROP=0
B: EV=1b
B: KEY=401 0 1 0 0 0 0 0 0 0 0
B: ABS=100 3
B: MSC=10

in config.txt, I've added the following


Code:

max_usb_current=1
  hdmi_group=2
  hdmi_mode=87
  hdmi_cvt 1024 600 60 6 0 0 0
  hdmi_drive=1
  



Everything works fine for display, except the touchpad feature. only
top-left corner seems ok. I cannot press anything on Jivelite. I must
use a mouse to configure and use jivelite.

So I presume I shall calibrate the touchscreen. I did the following:


Code:

sudo TSLIB_FBDEVICE=/dev/fb0 TSLIB_TSDEVICE=/dev/input/event6 
/usr/local/bin/ts_calibrate 



I see the crosshair.

It seems the calibration process does not work well: sometimes it does
not pass via all the corners points and jumps directly to the end. Thus
the calibration file pointercal is not good.

Here is my ts.conf file: 


Code:


  # Access plugins
  
  
  # Uncomment if you wish to use the linux input layer event interface
  module_raw input
  
  # For other driver modules, see the ts.conf man page
  
  
  # Filter plugins
  
  
  # Uncomment if first or last samples are unreliable
  # module skip nhead=1 ntail=1
  
  # Uncomment if needed for devices that measure pressure
  #module pthres pmin=1
  
  #module variance delta=30
  
  # Uncomment if needed
  module debounce drop_threshold=500
  
  # Uncomment if needed to filter spikes
  # module median depth=5
  
  # Uncomment to enable smoothing of fraction N/D
  # module iir N=6 D=10
  
  # Uncomment if needed
  # module lowpass factor=0.1 threshold=1
  
  # Uncomment if needed to filter noise samples
  #module dejitter delta=100
  
  # Uncomment and adjust if you need to invert an axis or both
  # module invert x0=800 y0=480
  #module invert x0=1024 y0=600
  
  # Uncomment to use ts_calibrate's settings
  module linear
  



I tried to use different values, no effect.

I tried to calibrate by pressing very fast the screen to pass
successfully to 5 area and I got this: 


Code:


  tc@piCorePlayer:/usr/local/bin$ sudo TSLIB_FBDEVICE=/dev/fb0 
TSLIB_TSDEVICE=/dev/input/event6 /usr/local/bin/ts_calibrate
  xres = 1024, yres = 600
  Took 4 samples...
  Top left : X =   16 Y =  600
  Took 11 samples...
  Top right : X =0 Y =  600
  Took 10 samples...
  Bot right : X =0 Y =  600
  Took 8 samples...
  Bot left : X =0 Y =  600
  Took 18 samples...
  Center : X =0 Y =  600
  ts_calibrate: determinant is too small -- 0.00
  Calibration failed.
  



Sometimes, when it skips some calibration corners, the file is properly
generated but of course the parameters are wrong. 

So I'm stuck. is there an alternative to generate this pointercal config
file ? to calibrate this screen ? 

I've done some search on this forum and abroad without finding the right
calibration parameters.


any idea to solve that problem ? 

Thank you and happy new year to all !

Thomas

PS: i tried this touchsreen on Standard Raspbian desktop OS and it works
like a charm without any config except config.txt



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=111447

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Jivelite for piCorePlayer

2020-01-03 Thread tparvais 


chewiiie wrote: 
> Hello ianjh123
> Did you manage to get your touchscreen working properly ? I have the
> same issue with my 7inch Waveshare touchscreen. If so, could you explain
> how you did it please ?
> Thanks

Hello

I've the same issue: impossible to calibrate my waveshare 7" LCD (C).

it jumps directly to center calibrtion and then the calibration data are
not ok

any idea ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=103330

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Touch off with Jivelite/Waveshare 5" on piCorePlayer

2020-01-03 Thread tparvais 


Xyzzy wrote: 
> For my Waveshare screen:
> 
> cat /proc/bus/input/devices -> find right parameters to use below (like
> fbx, eventy)
> 
> sudo TSLIB_FBDEVICE=/dev/fb1 TSLIB_TSDEVICE=/dev/input/event0
> /usr/local/bin/ts_calibrate
> optional: sudo TSLIB_FBDEVICE=/dev/fb1 TSLIB_TSDEVICE=/dev/input/event0
> /usr/local/bin/ts_test
> 
> Find jivelite.sh in the filesystem, copy to 
> $TCEMNT/tce/jivelite.sh (/mnt/mmcblk0p2/tce/jivelite.sh in my case)
> 
> Add next to other exports (use your own values) in the copied
> jivelite.sh:
> export SDL_VIDEODRIVER=fbcon
> export SDL_FBDEV=/dev/fb0
> export SDL_MOUSEDEV=/dev/input/event0
> export SDL_MOUSEDRV=TSLIB
> 
> Make piCore backup.
> 
> Reboot

Hello

I have the following touchscreen 7'' Waveshare HDMI LCD (C) on a
raspberrypi 3B with PicorePlayer 5.0

I adapted pcp_startup.sh accordingly to use *BYZHYYZHY By ZH851
Touchscreen* as identifier.

I: Bus=0003 Vendor=0eef Product=0005 Version=0110
N: Name="BYZHYYZHY By ZH851 Mouse"
P: Phys=usb-3f98.usb-1.4/input0
S:
Sysfs=/devices/platform/soc/3f98.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:0EEF:0005.0004/input/input6
U: Uniq=c0U585P865
H: Handlers=mouse1 event5 js0
B: PROP=0
B: EV=1b
B: KEY=7 0 0 0 0 0 0 0 0
B: ABS=3
B: MSC=10

I: Bus=0003 Vendor=0eef Product=0005 Version=0110
N: Name="BYZHYYZHY By ZH851 Touchscreen"
P: Phys=usb-3f98.usb-1.4/input0
S:
Sysfs=/devices/platform/soc/3f98.usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:0EEF:0005.0004/input/input7
U: Uniq=c0U585P865
H: Handlers=mouse2 event6
B: PROP=0
B: EV=1b
B: KEY=401 0 1 0 0 0 0 0 0 0 0
B: ABS=100 3
B: MSC=10

in config.txt, I've added the following


Code:

max_usb_current=1
  hdmi_group=2
  hdmi_mode=87
  hdmi_cvt 1024 600 60 6 0 0 0
  hdmi_drive=1
  



Everything works fine for display, except the touchpad feature. only
top-left corner seems ok. I cannot press anything on Jivelite.

I tried to calibrate with 


Code:

sudo TSLIB_FBDEVICE=/dev/fb0 TSLIB_TSDEVICE=/dev/input/event6 
/usr/local/bin/ts_calibrate 



When I tried a test with ts_test, it does not work: the pointer does not
move.

I've seen in PDF document dtoverlay command has been also set, but I
don't know what to use in my case

any idea to solve that problem ? 

Thank you and happy new year to all !

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=109619

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Picoreplayer on Pi : problem to access remote NFS drive

2018-09-01 Thread tparvais 


paul- wrote: 
> I use a synology nfs mount, here is the mount configuration.
> 
> 25550
> 
> How is your NFS setup on the synology.

here is mine: identical to your's

25553

my syno config:

25554

thank you


+---+
|Filename: ds.jpg   |
|Download: http://forums.slimdevices.com/attachment.php?attachmentid=25554|
+---+


tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=109402

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

[SlimDevices: Unix] Picoreplayer on Pi : problem to access remote NFS drive

2018-09-01 Thread tparvais 


Hello

Upgrading my PCP to beta 4 I try a new config with LMS installed locally
and USB drive for caching.
I want to mount via NFS music folder from my synology. I use synology
standard NFS parameter that work from others devices, but not from PCP.

Everything seems working on the web interface, but when in LMS I
configure this extra music source  (/mnt/ds916) , it does not display
the /mnt/ds916 music subfolders.
I have the feeling there is a RW acecss permission issue on /mnt/ds916
on PCP

When looking with SSH, I can access /mnt/ds916 only if I'm root but not
with normal "tc" user account.

any idea ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=109402

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce piCorePlayer 3.20

2017-06-06 Thread tparvais 

paul- wrote: 
> First, make sure you have the correct card selected.  You should have
> this in the drop down box 
> 
> HiFiBerry AMP (and +)
> 
> This is the default output and alsa parameters for the card
> 
> 22842

Hello Paul

Of course , I selected the right board. I have 2 Amp hifiberry. It was
working fine before 3.2

I tried to play with Alsa buffer without success.

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=107352

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce piCorePlayer 3.20

2017-06-05 Thread tparvais 

Hello

I change the network confit on my pi 2 from wifi to Ethernet and
hifiberry Amp.

I had to reinstall completely the software

Now, I don't have any clear sound anymore, some times 1-2s and then
nothing anymore.
I check speed network test with iperf3 and it's almost perfect

I don't understand what's the problem

The diagnostic shows that squeeze lite is running with the following ( I
tried to change the buffer, but I. Don't understand this well)

/usr/local/bin/squeezelite -n Sauna -o hw:CARD=sndrpihifiberry -a 400 8 
0

Any help will be appreciated 

Thank you

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=107352

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2017-05-08 Thread tparvais 

Greg Erskine wrote: 
> Hi tparvais,
> 
> If you are using a RPi3B, did you disable the built-in wifi?
> 
> regards
> Greg

Hello Greg 

This is a pi2+. 
I have upgraded to picoreplayer 3.2 yesterday 

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2017-05-07 Thread tparvais 

Hello

With PC 3.2, if the pi reboots, I sometimes loose wifi connectivity. It
cannot mount the wifi dongle properly. Seems not stable.

LSUSB shows wifi dongle 148F:5370 RALINK RT5370

Wifi coverage is good at the pi location.

What can be the rootcause ?

LSMOD:

Code:

Module  Size  Used byNot tainted
  ctr 4262  4 
  ccm 9232  2 
  arc42076  2 
  rt2800usb  18973  0 
  rt2x00usb  12932  1 rt2800usb
  rt2800lib  82219  1 rt2800usb
  rt2x00lib  49062  3 rt2800usb,rt2x00usb,rt2800lib
  mac80211  650451  3 rt2x00usb,rt2800lib,rt2x00lib
  cfg80211  525710  2 rt2x00lib,mac80211
  snd_soc_tas5713 6256  1 
  rfkill 21373  2 cfg80211
  snd_soc_hifiberry_amp 3059  0 
  snd_soc_bcm2835_i2s 6283  2 
  crc_ccitt   1732  1 rt2800lib
  snd_soc_core  175744  3 
snd_soc_tas5713,snd_soc_hifiberry_amp,snd_soc_bcm2835_i2s
  snd_pcm_dmaengine   6002  1 snd_soc_core
  snd_bcm283523131  0 
  snd_pcm96519  3 snd_soc_core,snd_pcm_dmaengine,snd_bcm2835
  snd_timer  22674  1 snd_pcm
  snd_compress   10144  1 snd_soc_core
  snd68784  5 
snd_soc_core,snd_bcm2835,snd_pcm,snd_timer,snd_compress
  regmap_mmio 3977  1 snd_soc_bcm2835_i2s
  fixed   3029  0 
  squashfs   32058 34 
  lz4 1667  1 
  lz4_compress3289  1 lz4
  zram   20493  1 
  zsmalloc   16298  1 zram
  spi_bcm2835 7424  0 
  bcm2835_gpiomem 3791  0 
  i2c_bcm2835 6369  0 
  uio_pdrv_genirq 3718  0 
  uio10166  1 uio_pdrv_genirq
  



Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: Slimmer

2017-04-16 Thread tparvais 

Hello

Can you please give more details on hardware items required to build
this screen+keys buttons ? I cannot find any exact details on the
different coonections to build and the GPIO to use

How is it compatible with HifiBereryPI AMP ? (GPIO 2-3 & 28-31 are used
by AMP hat) ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105819

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.10

2017-03-27 Thread tparvais 

paul- wrote: 
> Support for shairport-sync will probably be dropped soon.  It's too
> difficult to manage for something that us developers don't use.  Look at
> Shairtunes2W.  
> 
> Shairtunes2W runs fine on a pCP LMS installation.

Hello

Is it also working fine on lms running on synology ds916+ ? 
Thank you 


Envoyé de mon iPhone en utilisant Tapatalk





tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=106755

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.10

2017-03-26 Thread tparvais 

paul- wrote: 
> It seems to be card dependent.  I have no problems with my cards that I
> use for testing.  IQaudio Amp, Allo Piano, Builtin audio.
> 
> Shairtunes2W is a much better implementation, I would really take a look
> at that.


Hello

with last P3.11 & Hifiberry AMP+, shairport does not work: nothing
displayed on my ios device

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=106755

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2016-12-20 Thread tparvais 

paul- wrote: 
> Ext4 works great, pCP is linux after all.   But not everyone has the
> tools to do a ext4 partition on a windows machine.   We currently only
> have automatic mounting on 1 USB device.  You can use 2, but then you
> need to manually set it up.

I've converted VFAT to NTFS on windows with command "CONVERT" without
losing my data
It's working perfectly now

thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2016-12-20 Thread tparvais 

paul- wrote: 
> It is fine for music, it is the cache and database that cannot go on a
> vfat partition.   You can leave the cache on the sdcard, but I would
> recommend reformatting your hard disk and putting the music and cache on
> it.
> 
> If you are formatting on a windows machine.  Ntfs format will work too.

NTFS is the only type fully compatible with music & cache ? that's pitty
VFAT does not work.

I'll try to change type to NTFS with a window tool

I'm worrying that yusing SDCARD for cache will burn rapidely the SDCard



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2016-12-20 Thread tparvais 

paul- wrote: 
> You need to reformat your hard disk if you want to move the LMS cache
> and database on it.

Hello Paul,
This disk has just been reformated before I copy my music on it from my
PC. why should I reformat again ? which type of format ?



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2016-12-20 Thread tparvais 

Hello

I connected external USB HDD containing all my music. I installed LMS on
picoreplayer (Pi 2)
I mount this HDD :  /dev/sda1 vfat 5855-1C4F 465 GB

In LMS config, I can delcare this hdd for the music, it works fine. On
SSH, everything is OK

but when I click to move the LMS data cache to USB-HDD
(/mnt/hdd/slimserver), I got the following error message:
> [ERROR] Unsupported partition type detected (vfat), please use a ntfs or
> linux partition type for Cache storate. (i.e. ext4)

I don't understand why I cannot do that...

thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Jivelite for piCorePlayer

2016-11-27 Thread tparvais 

Hello

I've connected a touch Waveshare 1024*600 7" screen. IT works but
resolution and display output is shifted to the right. I presume this is
due to wrong resolution

How it is possible to adapt ?

Thank you

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=103330

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2016-11-26 Thread tparvais 

hello

I tried to install PCP 3.02 on PI2 using wifi dongle EW-7811Un

I reboot multiple times. I defined SSID+Password correctly.

IP over wifi does not come up

The wifi dongle seems correctly installed. it detects the Wifi MAC
address but I've the following message: "Wifi IP: is missing - reboot or
connect required." 

DMESG
> [3.413829] usb 1-1.3: New USB device found, idVendor=abcd,
> idProduct=1234
> [3.413846] usb 1-1.3: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [3.413858] usb 1-1.3: Product: UDisk   
> [3.413868] usb 1-1.3: Manufacturer: General 
> [3.413879] usb 1-1.3: SerialNumber: 
> .
> [3.594655] usb 1-1.4: New USB device found, idVendor=7392,
> idProduct=7811
> [3.594671] usb 1-1.4: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [3.594683] usb 1-1.4: Product: 802.11n WLAN Adapter
> [3.594694] usb 1-1.4: Manufacturer: Realtek
> [3.594705] usb 1-1.4: SerialNumber: 00e04c01

LOADED MODULE
> Module  Size  Used byTainted: G  
> 8192cu568110  0 
> cfg80211  440795  1 8192cu
> rfkill 16702  1 cfg80211
> squashfs   29704 31 
> zram   21852  1 
> zsmalloc   12458  1 zram
> lz4_compress3028  1 zram

IWCONFIG RESULTS
> wlan0 unassociated  Nickname:""
> Mode:Managed  Frequency=2.412 GHz  Access Point:
> Not-Associated   
> Sensitivity:0/0  
> Retry:off   RTS thr:off   Fragment thr:off
> Encryption key:off
> Power Management:off
> Link Quality:0  Signal level:0  Noise level:0
> Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
> Tx excessive retries:0  Invalid misc:0   Missed beacon:0

LSUSB RESULT
> Bus 001 Device 005: ID 7392:7811 Edimax Technology Co., Ltd EW-7811Un
> 802.11n Wireless Adapter [Realtek RTL8188CUS]
> Bus 001 Device 004: ID abcd:1234 Unknown 


any idea ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: piCorePlayer 3.00

2016-09-07 Thread tparvais 

Hello

i installed a fresh 3.01 PP on SDcard on my Pi2.
I installed then LMS
I want to mount my music drive via NFS from my synology. I understand
I've to install first extra filesystems by using "Install and Enable
additional FileSystems"

I have the following:

[ INFO ] Downloading: filesystems-4.4.15-piCore_v7+.tcz Error on
filesystems-4.4.15-piCore_v7+.tcz 1

[ INFO ] Loadingntfs-3g.tcz not found! 1

[ INFO ] NTFS Support Loaded...

And it's not possible to add a NFS mount ?

Any idea ?

Another question: I also could use USB HDD, how is it possible to make
it shared on network to push on it new music files ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=105997

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] piCoPlayer = Squeezelite on Microcore linux. .An embedded OS in RAM with Squeezelite

2015-03-18 Thread tparvais 

Hello

I've picoreplayer + USB DAC (PCM2704). I want to know if I shall use a
specific parameter to use at the maximum DAC capacity ?

I read alot about 96Khz sampling etc...

I'm listing to FLAC and 320Kbps MP3.

Is the DAC converting automatically to best quality ?
Is there a parameter to upscale the source ? if this is useful ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97803

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] piCoPlayer = Squeezelite on Microcore linux. .An embedded OS in RAM with Squeezelite

2015-01-21 Thread tparvais 

Hello

I've a small usb key I'd like to use for picoreplayer

IS it possible to use it, to install the image and to boot from USB key
vs. SDCard ?

Thank you



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97803

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] piCoPlayer = Squeezelite on Microcore linux. .An embedded OS in RAM with Squeezelite

2013-05-23 Thread tparvais 

Hello

Thanks for the image and concept. good idea !

I tested the last 0.9. Wifi perfectly works.

Sound outputs via 3.5mm jack or HDMI work also

But impossible to have a sound without noise and distorsion via my USB
DAC (PCM2704 based). I tried -a 800:4, -o front:CARD=DAC,DEV=0 as
proposed by the setup tool, try to apply of course the change etc...

Is it also possible to configure the keyboard via the small setup tool ?
My keyboard is AZERTY and not QWERTY

Thank you

thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97803

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] piCoPlayer = Squeezelite on Microcore linux. .An embedded OS in RAM with Squeezelite

2013-05-23 Thread tparvais 

sbp wrote: 
 Tanks for trying piCorePlayer. I think that your USB is supported, it
 seems similar to what others have reported to be working, as indicated
 on the web page.
 
 What is the output if you put in the USB card and then use option 3 in
 the small menu program?
 
 Steen

Hi

I tried to connect with Putty. With my AZerty keyboard, I cant login
with tc/nosoup4u SSH for a copy paste of the result. is there a trick ?



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97803

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] piCoPlayer = Squeezelite on Microcore linux. .An embedded OS in RAM with Squeezelite

2013-05-23 Thread tparvais 

sbp wrote: 
 Tanks for trying piCorePlayer. I think that your USB is supported, it
 seems similar to what others have reported to be working, as indicated
 on the web page.
 
 What is the output if you put in the USB card and then use option 3 in
 the small menu program?
 
 Steen

Finally, I succeed to login with Putty. and strange thing, it recognize
automatically my AZERTY keyboard and adapt accordingly :-) Strange
different behaviour between ssh and direct connection

Here is the output:

Insert USB DAC and pres ENTER to get a list of available ALSA device
Output devices:
null   - Discard all samples (playback) or
generate zero samples (capture)
default:CARD=ALSA  - bcm2835 ALSA, bcm2835 ALSA - Default
Audio Device
sysdefault:CARD=ALSA   - bcm2835 ALSA, bcm2835 ALSA - Default
Audio Device
default:CARD=DAC   - USB Audio DAC, USB Audio - Default
Audio Device
sysdefault:CARD=DAC- USB Audio DAC, USB Audio - Default
Audio Device
front:CARD=DAC,DEV=0   - USB Audio DAC, USB Audio - Front
speakers
surround40:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 4.0
Surround output to Front and Rear speakers
surround41:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 4.1
Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 5.0
Surround output to Front, Center and Rear speakers
surround51:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 5.1
Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 7.1
Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - IEC958
(S/PDIF) Digital Audio Output


I tried the option like:

-a 500:4 -n PiCuisine -o front:CARD=DAC,DEV=0 but does not work

Thank you

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97803

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] piCoPlayer = Squeezelite on Microcore linux. .An embedded OS in RAM with Squeezelite

2013-05-23 Thread tparvais 

I continue my trial and reboot the Pi and not it WORKS ! Sorry for
having posted some useless messgaes ;-)

Thank you anyway for the support Steen !

Thomas

PS: any idea if adding Shairport is feasible ? 



tparvais wrote: 
 Finally, I succeed to login with Putty. and strange thing, it recognize
 automatically my AZERTY keyboard and adapt accordingly :-) Strange
 different behaviour between ssh and direct connection
 
 Here is the output:
 
 Insert USB DAC and pres ENTER to get a list of available ALSA device
 Output devices:
 null   - Discard all samples (playback) or
 generate zero samples (capture)
 default:CARD=ALSA  - bcm2835 ALSA, bcm2835 ALSA - Default
 Audio Device
 sysdefault:CARD=ALSA   - bcm2835 ALSA, bcm2835 ALSA - Default
 Audio Device
 default:CARD=DAC   - USB Audio DAC, USB Audio - Default
 Audio Device
 sysdefault:CARD=DAC- USB Audio DAC, USB Audio - Default
 Audio Device
 front:CARD=DAC,DEV=0   - USB Audio DAC, USB Audio - Front
 speakers
 surround40:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 4.0
 Surround output to Front and Rear speakers
 surround41:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 4.1
 Surround output to Front, Rear and Subwoofer speakers
 surround50:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 5.0
 Surround output to Front, Center and Rear speakers
 surround51:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 5.1
 Surround output to Front, Center, Rear and Subwoofer speakers
 surround71:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - 7.1
 Surround output to Front, Center, Side, Rear and Woofer speakers
 iec958:CARD=DAC,DEV=0  - USB Audio DAC, USB Audio - IEC958
 (S/PDIF) Digital Audio Output
 
 
 I tried the option like:
 
 -a 500:4 -n PiCuisine -o front:CARD=DAC,DEV=0 but does not work
 
 Thank you
 
 Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97803

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix

Re: [SlimDevices: Unix] Announce: Squeezelite - a small headless squeezeplay emulator for linux (alsa only)

2013-05-16 Thread tparvais 

Hello

Thank you for this great tool, just installed on my Pi to replace a
Squeezebox.Running fine with Synology as main server (LMS)

I'm looking how to play automatically a radio station (or one of my
favorite) just after the boot.

Squeezelite is started automatically, but the music/radio is not
launched automatically ?

IS there a specifis parameter to use on squeezelite to play radio
directly ?

Thank you

Thomas



tparvais's Profile: http://forums.slimdevices.com/member.php?userid=59976
View this thread: http://forums.slimdevices.com/showthread.php?t=97046

___
unix mailing list
unix@lists.slimdevices.com
http://lists.slimdevices.com/mailman/listinfo/unix