Re: [ovirt-users] FC QLogic question
Sorry for delay in replying on this, I got pulled into some urgent meetings at the end of the day. Regarding the questions below, Yes under the H/W tab my QLogic cards are listed. Looks like I have two different models of cards, which could be, I think I acquired them off ebay and then got another one later for redundancy. WWNN and WWPNs are listed. Miultipath -ll lists all my LUNs, multipathing is set to RR... not sure if that could be problem as the SAN I am using (old EMC/DGC CX200) is active passive and I would assume it would be MRU... Hope this helps, still no LUNs showing up in my Engine. Thanks again for your help. Bill -Original Message- From: Daniel Helgenberger [mailto:daniel.helgenber...@m-box.de] Sent: 11 September 2014 13:06 To: Bill Dossett Subject: Re: [ovirt-users] FC QLogic question On 11.09.2014 13:05, Bill Dossett wrote: Hi Daniel, I did a lsmod | grep qxl and it returned nothing... did you perhaps mean qla? [root@ovirt141 ~]# lsmod | grep qla qla2xxx 466573 56 I think that is the one Indeed, sorry for that. lsscsi does list all of the LUNs... so that's working! Great! But nothing in ovirt engine when I try to add a storage domain. Please check back in ovirt engine, with Hosts / Hardware info. You should see the adapter there, along with WWN's ect. I am not quite sure, but AFAIK the node uses dm-multipath by default (for iscsi multipathing). So what does: # multipath -ll list? Thanks again, I guess I will try and get a bit further with the installs I have... Bill -Original Message- From: Daniel Helgenberger [mailto:daniel.helgenber...@m-box.de] Sent: 11 September 2014 11:53 To: Bill Dossett Subject: Re: [ovirt-users] FC QLogic question On 11.09.2014 12:17, Bill Dossett wrote: Thanks for responding Daniel. Never mind! I was wondering and thought the message may be irrelevant. But yes, it doesn't appear to be working. When I try to add a FC storage domain, no hosts are showing in the drop down box of hosts. I have loaded the latests ovirtnode (3.4.something...) on two hosts now and neither are working. Lets first try to isolate your FC issure. So you are using the latest ovirt-node? EL6? Keep in mind, the kernel is standard Linux and therefore should support Qlogic adapters out of the box (IMHO they are the best supported HBAs in Linux). Please try a: # lsmod | grep qxl to see whatever the qxl module is loaded. Keep in mind you can run into problems with other conrollers in your host, though I only had this with LSI SAS / FC controllers so far. Further check on the FC switch if the N port is logged in and the zoning is correct. Finally, check with # lsscsi if you can see the luns. Also having a lot of issues with configuring the network. I configure an interface I can ping it, but it shows as unconfigured... on one host I have added it to the manager and I see the interfaces anyway, but on the second host I configure the eth0, I can ping it, it added to the ovirt engine but it shows no NICs. Should I be using an earlier version maybe? thanks again and best regards. *Bill Dossett* *Virtualisation Architect* *Pitney Bowes - Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.doss...@pb.com mailto:bill.doss...@pb.com www.pb.com http://www.pb.com/ *In Engineering?**Raise a ticket via Remedy Anywhere [HERE http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Inciden t /newIncident.aspx]takes less than a minute* *ManageIQ User Guide available* [*HERE https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%2 0 v4.pdf*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx * On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger daniel.helgenber...@m-box.de mailto:daniel.helgenber...@m-box.de wrote: Hello Bill, what are your problems acually? Is fibre channel not working (as expected)? The log snippet you provided is completly normal and the messages can safely be ignored. This is also unrelated to oVirt but rather CentOS (or the distro you are running) I suppose. Cheers! On 11.09.2014 10:51, Bill Dossett wrote: Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep
[ovirt-users] FC QLogic question
Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ :0c:00.0 hdma+ host#=1 fw=4.00.26 (2). Sep 9 08:01:27 localhost kernel: ata_piix :00:1f.1: PCI INT A - GSI 16 (level, low) - IRQ 16 I have googled the firmware error and it says some cards need a firmware flash and some don't. These are pretty standard HBAs so I would think they would be supported out of the box, but maybe not. Looking at trying to add the firmware looked kind of complex - if I need to do this, does anyone know of a nice and easy howto guide on this. I'm just getting started with ovirt and appreciate any help Thanks Bill Dossett Virtualisation Architect Pitney Bowes - Tech Central 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone (+44) (0)1923 279353 | VOIP: 54739353 Mobile (+44) (0)7775 908612 bill.doss...@pb.commailto:bill.doss...@pb.com www.pb.comhttp://www.pb.com/ In Engineering? Raise a ticket via Remedy Anywhere [HEREhttp://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx] takes less than a minute ManageIQ User Guide available [HEREhttps://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf] Check out the ManageIQ Blog for recent enhancements and information [HERE]http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] FC QLogic question
Hello Bill, what are your problems acually? Is fibre channel not working (as expected)? The log snippet you provided is completly normal and the messages can safely be ignored. This is also unrelated to oVirt but rather CentOS (or the distro you are running) I suppose. Cheers! On 11.09.2014 10:51, Bill Dossett wrote: Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ :0c:00.0 hdma+ host#=1 fw=4.00.26 (2). Sep 9 08:01:27 localhost kernel: ata_piix :00:1f.1: PCI INT A - GSI 16 (level, low) - IRQ 16 I have googled the firmware error and it says some cards need a firmware flash and some don’t. These are pretty standard HBAs so I would think they would be supported out of the box, but maybe not. Looking at trying to add the firmware looked kind of complex – if I need to do this, does anyone know of a nice and easy howto guide on this. I’m just getting started with ovirt and appreciate any help Thanks *Bill Dossett* *Virtualisation Architect* *Pitney Bowes – Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.doss...@pb.com mailto:bill.doss...@pb.com www.pb.com http://www.pb.com/ *In Engineering?**Raise a ticket via Remedy Anywhere [HERE http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx]takes less than a minute* *ManageIQ User Guide available*[*HERE https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx* -- Daniel Helgenberger m box bewegtbild GmbH P: +49/30/2408781-22 F: +49/30/2408781-10 ACKERSTR. 19 D-10115 BERLIN www.m-box.de www.monkeymen.tv Geschäftsführer: Martin Retschitzegger / Michaela Göllner Handeslregister: Amtsgericht Charlottenburg / HRB 112767 ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] FC QLogic question
Thanks for responding Daniel. I was wondering and thought the message may be irrelevant. But yes, it doesn’t appear to be working. When I try to add a FC storage domain, no hosts are showing in the drop down box of hosts. I have loaded the latests ovirtnode (3.4.something…) on two hosts now and neither are working. Also having a lot of issues with configuring the network. I configure an interface I can ping it, but it shows as unconfigured… on one host I have added it to the manager and I see the interfaces anyway, but on the second host I configure the eth0, I can ping it, it added to the ovirt engine but it shows no NICs. Should I be using an earlier version maybe? thanks again and best regards. Bill Dossett Virtualisation Architect Pitney Bowes – Tech Central 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone (+44) (0)1923 279353 | VOIP: 54739353 Mobile (+44) (0)7775 908612 bill.doss...@pb.commailto:bill.doss...@pb.com www.pb.comhttp://www.pb.com/ In Engineering? Raise a ticket via Remedy Anywhere [HEREhttp://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx] takes less than a minute ManageIQ User Guide available [HEREhttps://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf] Check out the ManageIQ Blog for recent enhancements and information [HERE]http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger daniel.helgenber...@m-box.demailto:daniel.helgenber...@m-box.de wrote: Hello Bill, what are your problems acually? Is fibre channel not working (as expected)? The log snippet you provided is completly normal and the messages can safely be ignored. This is also unrelated to oVirt but rather CentOS (or the distro you are running) I suppose. Cheers! On 11.09.2014 10:51, Bill Dossett wrote: Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ :0c:00.0 hdma+ host#=1 fw=4.00.26 (2). Sep 9 08:01:27 localhost kernel: ata_piix :00:1f.1: PCI INT A - GSI 16 (level, low) - IRQ 16 I have googled the firmware error and it says some cards need a firmware flash and some don’t. These are pretty standard HBAs so I would think they would be supported out of the box, but maybe not. Looking at trying to add the firmware looked kind of complex – if I need to do this, does anyone know of a nice and easy howto guide on this. I’m just getting started with ovirt and appreciate any help Thanks *Bill Dossett* *Virtualisation Architect* *Pitney Bowes – Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.doss...@pb.commailto:bill.doss...@pb.com mailto:bill.doss...@pb.com www.pb.comhttp://www.pb.com http://www.pb.com/ *In Engineering?**Raise a ticket via Remedy Anywhere [HERE http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx]takes less than a minute* *ManageIQ User Guide available*[*HERE https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx* -- Daniel Helgenberger m box bewegtbild GmbH P: +49/30/2408781-22 F: +49/30/2408781-10 ACKERSTR. 19 D-10115 BERLIN www.m-box.dehttp://www.m-box.de www.monkeymen.tvhttp://www.monkeymen.tv Geschäftsführer: Martin Retschitzegger / Michaela Göllner Handeslregister: Amtsgericht Charlottenburg / HRB 112767 ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
Re: [ovirt-users] FC QLogic question
I'm guessing my problems are to do with using the ovirt node hypervisor install from the ovirt web site to boot and configure from. I'm going to download CentOS 6.5 and setup that up and then put ovirt on top of it. I have used CentOS on these systems before and they were fine using the FC SAN. I get the feeling that NFS and iSCSI support is probably fine, but I the FC support may not be so good, well that's my guess anyway. Thanks again From: users-boun...@ovirt.org [mailto:users-boun...@ovirt.org] On Behalf Of Bill Dossett Sent: 11 September 2014 11:17 To: Daniel Helgenberger Cc: users@ovirt.org Subject: Re: [ovirt-users] FC QLogic question Thanks for responding Daniel. I was wondering and thought the message may be irrelevant. But yes, it doesn't appear to be working. When I try to add a FC storage domain, no hosts are showing in the drop down box of hosts. I have loaded the latests ovirtnode (3.4.something...) on two hosts now and neither are working. Also having a lot of issues with configuring the network. I configure an interface I can ping it, but it shows as unconfigured... on one host I have added it to the manager and I see the interfaces anyway, but on the second host I configure the eth0, I can ping it, it added to the ovirt engine but it shows no NICs. Should I be using an earlier version maybe? thanks again and best regards. Bill Dossett Virtualisation Architect Pitney Bowes - Tech Central 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone (+44) (0)1923 279353 | VOIP: 54739353 Mobile (+44) (0)7775 908612 bill.doss...@pb.commailto:bill.doss...@pb.com www.pb.comhttp://www.pb.com/ In Engineering? Raise a ticket via Remedy Anywhere [HEREhttp://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx] takes less than a minute ManageIQ User Guide available [HEREhttps://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf] Check out the ManageIQ Blog for recent enhancements and information [HERE]http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger daniel.helgenber...@m-box.demailto:daniel.helgenber...@m-box.de wrote: Hello Bill, what are your problems acually? Is fibre channel not working (as expected)? The log snippet you provided is completly normal and the messages can safely be ignored. This is also unrelated to oVirt but rather CentOS (or the distro you are running) I suppose. Cheers! On 11.09.2014 10:51, Bill Dossett wrote: Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ :0c:00.0 hdma+ host#=1 fw=4.00.26 (2). Sep 9 08:01:27 localhost kernel: ata_piix :00:1f.1: PCI INT A - GSI 16 (level, low) - IRQ 16 I have googled the firmware error and it says some cards need a firmware flash and some don't. These are pretty standard HBAs so I would think they would be supported out of the box, but maybe not. Looking at trying to add the firmware looked kind of complex - if I need to do this, does anyone know of a nice and easy howto guide on this. I'm just getting started with ovirt and appreciate any help Thanks *Bill Dossett* *Virtualisation Architect* *Pitney Bowes - Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.doss...@pb.commailto:bill.doss...@pb.com mailto:bill.doss...@pb.com www.pb.comhttp://www.pb.com http://www.pb.com/ *In Engineering?**Raise a ticket via Remedy Anywhere [HERE http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx]takes less than a minute* *ManageIQ User Guide available*[*HERE https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx* -- Daniel Helgenberger m box bewegtbild GmbH P: +49/30/2408781-22 F: +49/30/2408781-10 ACKERSTR. 19 D-10115 BERLIN www.m-box.dehttp://www.m-box.de www.monkeymen.tvhttp://www.monkeymen.tv Geschäftsführer: Martin Retschitzegger / Michaela Göllner Handeslregister: Amtsgericht Charlottenburg / HRB 112767
Re: [ovirt-users] FC QLogic question
On 11.09.2014 12:17, Bill Dossett wrote: Thanks for responding Daniel. Never mind! I was wondering and thought the message may be irrelevant. But yes, it doesn’t appear to be working. When I try to add a FC storage domain, no hosts are showing in the drop down box of hosts. I have loaded the latests ovirtnode (3.4.something…) on two hosts now and neither are working. Lets first try to isolate your FC issure. So you are using the latest ovirt-node? EL6? Keep in mind, the kernel is standard Linux and therefore should support Qlogic adapters out of the box (IMHO they are the best supported HBAs in Linux). Please try a: # lsmod | grep qxl to see whatever the qxl module is loaded. Keep in mind you can run into problems with other conrollers in your host, though I only had this with LSI SAS / FC controllers so far. Further check on the FC switch if the N port is logged in and the zoning is correct. Finally, check with # lsscsi if you can see the luns. Also having a lot of issues with configuring the network. I configure an interface I can ping it, but it shows as unconfigured… on one host I have added it to the manager and I see the interfaces anyway, but on the second host I configure the eth0, I can ping it, it added to the ovirt engine but it shows no NICs. Should I be using an earlier version maybe? thanks again and best regards. *Bill Dossett* *Virtualisation Architect* *Pitney Bowes – Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.doss...@pb.com mailto:bill.doss...@pb.com www.pb.com http://www.pb.com/ *In Engineering?**Raise a ticket via Remedy Anywhere [HERE http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx]takes less than a minute* *ManageIQ User Guide available* [*HERE https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx* On Sep 11, 2014, at 10:52 AM, Daniel Helgenberger daniel.helgenber...@m-box.de mailto:daniel.helgenber...@m-box.de wrote: Hello Bill, what are your problems acually? Is fibre channel not working (as expected)? The log snippet you provided is completly normal and the messages can safely be ignored. This is also unrelated to oVirt but rather CentOS (or the distro you are running) I suppose. Cheers! On 11.09.2014 10:51, Bill Dossett wrote: Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ :0c:00.0 hdma+ host#=1 fw=4.00.26 (2). Sep 9 08:01:27 localhost kernel: ata_piix :00:1f.1: PCI INT A - GSI 16 (level, low) - IRQ 16 I have googled the firmware error and it says some cards need a firmware flash and some don’t. These are pretty standard HBAs so I would think they would be supported out of the box, but maybe not. Looking at trying to add the firmware looked kind of complex – if I need to do this, does anyone know of a nice and easy howto guide on this. I’m just getting started with ovirt and appreciate any help Thanks *Bill Dossett* *Virtualisation Architect* *Pitney Bowes – Tech Central*** 6 Hercules Way, 600 Leavesden Park Watford, WD25 7GS Phone(+44) (0)1923 279353 | VOIP: 54739353 Mobile(+44) (0)7775 908612 bill.doss...@pb.com mailto:bill.doss...@pb.com mailto:bill.doss...@pb.com www.pb.com http://www.pb.com http://www.pb.com/ *In Engineering?**Raise a ticket via Remedy Anywhere [HERE http://teamsite.inside.pb.com/sites/TCPPM/GES/Lists/Create%20Incident/newIncident.aspx]takes less than a minute* *ManageIQ User Guide available*[*HERE https://dl.dropbox.com/u/6219441/ManageIQ%20-%20User%20Manual%20PB%20v4.pdf*] *Check out the ManageIQ Blog for recent enhancements and information [HERE] http://teamsite.inside.pb.com/sites/TCPPM/GES/manageiq/default.aspx* -- Daniel Helgenberger m box bewegtbild GmbH P: +49/30/2408781-22 F: +49/30/2408781-10 ACKERSTR. 19 D-10115 BERLIN
Re: [ovirt-users] FC QLogic question
Hi, there is an open bugreport on node that this firmware is missing, this is fixed in master branch: https://bugzilla.redhat.com/show_bug.cgi?id=1063001 my advice would be to install a plain centos 6.5 and to not use node atm. HTH On 11/09/14 10:51, Bill Dossett wrote: Hi, I seem to have run into a problem setting up ovirt with Fibre Channel storage. I have a 2MBs SAN and qlogic cards in the nodes. I used this same setup with RHEV about 6 months ago and it just worked, storage was there no problems. Now booting with ovirtnode distro, I am seeing Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-0091:1: Firmware images can be retrieved from: http://ldriver.qlogic.com/firmware/. Sep 9 08:01:27 localhost kernel: scsi1 : qla2xxx Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fb:1: QLogic QLE2460 - QLogic 4GB FC Single-Port PCI-E HBA for IBM System x. Sep 9 08:01:27 localhost kernel: qla2xxx [:0c:00.0]-00fc:1: ISP2432: PCIe (2.5GT/s x4) @ :0c:00.0 hdma+ host#=1 fw=4.00.26 (2). Sep 9 08:01:27 localhost kernel: ata_piix :00:1f.1: PCI INT A - GSI 16 (level, low) - IRQ 16 -- Mit freundlichen Grüßen / Regards Sven Kieske Systemadministrator Mittwald CM Service GmbH Co. KG Königsberger Straße 6 32339 Espelkamp T: +49-5772-293-100 F: +49-5772-293-333 https://www.mittwald.de Geschäftsführer: Robert Meyer St.Nr.: 331/5721/1033, USt-IdNr.: DE814773217, HRA 6640, AG Bad Oeynhausen Komplementärin: Robert Meyer Verwaltungs GmbH, HRB 13260, AG Bad Oeynhausen ___ Users mailing list Users@ovirt.org http://lists.ovirt.org/mailman/listinfo/users
