Re: Micromac Speedy connections
I don't seem to be having any luck with this. I can tie the wires around the pins under the oscillator on my Turbo 040-40 and it works fine, but when I do it on my IIsi, it won't boot, it just starts up, doesn't chime, and the screen takes on one solid color until I turn it off again. I soldered the wires to the bottom of the motherboard under the oscillator, but I had the same result. I pulled off the solder and it worked again, but no luck getting the Speedy to work! ... Anyone know what I'm doing wrong? Thanks. -Original Message- From: Jane Thompson [EMAIL PROTECTED] Date: Tue, 25 Sep 2001 12:27:49 -0700 To: [EMAIL PROTECTED] (Vintage Macs) Subject: Re: Micromac Speedy connections Would this be a good application for Loctite, anyone? I was just reading about this in an article for repairing Duo keyboard leads. Jane Eric Wellington wrote: How do you think I should affix the wires to the oscillator solder pads on the bottom of the mobo? Scotch tape? Hot glue? I don't have access to a soldering iron, and I don't like soldering, either, it's too delicate a process. -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com -- Get your free email from www.linuxmail.org Powered by Outblaze -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: Micromac Speedy connections
At 22:00 +0800 on 25/09/01, Eric Wellington wrote: I have a MicroMac speedy that I'm trying to use in a IIsi. Unfortunately, after working with it for a little while, both clips fell apart, and one just broke in half. I'm left with two wires coming from the Speedy card. I've tried to connect these to the pins on the oscillator, but unfortunately, what always seems to happen is either one wire grounds to the oscillator casing, or the pins just don't touch the wires properly. Can anyone suggest a better method for attaching these to the motherboard? Would it be more effective for me to just hook these up to the solder pads underneath the motherboard, under the oscillator That would probably be best, yes. You don't want to chance shorting out a wire to the casing while the Mac is running. p _ the pickle The FAQ http://macfaq.binhost.com/ The Archive http://www.jmug.org/software/thepickle/ _ -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: Micromac Speedy connections
Would this be a good application for Loctite, anyone? I was just reading about this in an article for repairing Duo keyboard leads. Jane Eric Wellington wrote: How do you think I should affix the wires to the oscillator solder pads on the bottom of the mobo? Scotch tape? Hot glue? I don't have access to a soldering iron, and I don't like soldering, either, it's too delicate a process. -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: Micromac Speedy connections
Reply-to: [EMAIL PROTECTED] (Vintage Macs) To:[EMAIL PROTECTED] (Vintage Macs) Date: Tue, 25 Sep 2001 12:27:49 -0700 From: Jane Thompson [EMAIL PROTECTED] Subject: Re: Micromac Speedy connections Would this be a good application for Loctite, anyone? I was just reading about this in an article for repairing Duo keyboard leads. Jane Eric Wellington wrote: How do you think I should affix the wires to the oscillator solder pads on the bottom of the mobo? Scotch tape? Hot glue? I don't have access to a soldering iron, and I don't like soldering, either No and no both of yours. Soldering or clip on types are only way to do this properly. Cheers, Wizard -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: Micromac Speedy connections
Eric Wellington wrote: Unfortunately I do not want to invest that much time in the project. I plan to just get started on it right away. I've done some soldering, but only wires, not printed boards. I feel confident though that I can get it right first try, all I have to do is put down a little liquid solder onto the area where the wire touches the pad. Printed boards aren't much more complicated than just wires. One tip that will prevent you from having a cold solder joint, and therefore a bad connection, though, is to have all three elements in contact with the tip of the iron so that they are all a similar temperature. It's a quick operation, because the tracks or pads of the board will lift with too much heat. About a second is sufficient. Your joint should be shiny when done, and less is more. Good luck with it. jt -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
MicroMac Speedy
Does anyone know where I can find a MicroMac speedy? MicroMac wants $50 for one, but that's absurd! I can get an ACCELERATOR that will yield better beformance for that price. I reason I want one is that I want to try overclocking the 040 on my Turbo 040 card from 40mhz to 48mhz or higher. Does anyone know if this works? I read attempts to ground pin one and feed in a new signal failed in overclocking the Turbo i040-33mhz board, but this didn't use a Speedy. Thanks a lot, Deven Overclock the toaster! Gallo -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: MicroMac Speedy
Does anyone know where I can find a MicroMac speedy? MicroMac wants $50 for one, but that's absurd! I can get an ACCELERATOR that will yield better beformance for that price. I reason I want one is that I want to try overclocking the 040 on my Turbo 040 card from 40mhz to 48mhz or higher. Does anyone know if this works? I read attempts to ground pin one and feed in a new signal failed in overclocking the Turbo i040-33mhz board, but this didn't use a Speedy. you can get a powermac for that price. Why bother then? Marten Check out the System 6 Heaven: http://www.euronet.nl/users/mvdk/system_6_heaven.html -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: MicroMac Speedy
Date: Mon, 10 Sep 2001 09:34:27 EDT From: [EMAIL PROTECTED] Subject: MicroMac Speedy Does anyone know where I can find a MicroMac speedy? MicroMac wants $50 for one, but that's absurd! I can get an ACCELERATOR that will yield better beformance for that price. I reason I want one is that I want to try overclocking the 040 on my Turbo 040 card from 40mhz to 48mhz or higher. Does anyone know if this works? I read attempts to ground pin one and feed in a new signal failed in overclocking the Turbo i040-33mhz board, but this didn't use a Speedy. I had to lurk on ebay for quite a while to find one. Luckily, I wound up with the complete package in original box. The Speedy attaches to the CPU oscillator on the mobo, so I don't see how you could use it to accelerate the 040 card itself...? BTW, it easily ran my IIsi at 30 MHz+ (31.5 or 32.5 top speed, can't remember which), but I didn't try using the serial ports. Does anyone here have any direct experience (no hearsay, please) successfully using serial ports on accelerated IIsi...? -- Gene, a.k.a. G-Man Friends don't let friends do Windows -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: MicroMac Speedy
At 09:34 -0400 on 10/09/01, [EMAIL PROTECTED] wrote: Does anyone know where I can find a MicroMac speedy? MicroMac wants $50 for one, but that's absurd! I can get an ACCELERATOR that will yield better beformance for that price. I reason I want one is that I want to try overclocking the 040 on my Turbo 040 card from 40mhz to 48mhz or higher. Does anyone know if this works? I read attempts to ground pin one and feed in a new signal failed in overclocking the Turbo i040-33mhz board, but this didn't use a Speedy. 1) the Turbo i040 is an LC, not a full 040. 2) Disabling the crystal and feeding in a new signal is NOT the most reliable way to overclock. If you're gonna do it, just stick a new crystal in place of the old one. p _ the pickle The FAQ http://macfaq.binhost.com/ The Archive http://www.jmug.org/software/thepickle/ _ -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
Re: MicroMac Speedy
At 11:07 -0700 on 10/09/01, Gene Osburn wrote: I had to lurk on ebay for quite a while to find one. Luckily, I wound up with the complete package in original box. The Speedy attaches to the CPU oscillator on the mobo, so I don't see how you could use it to accelerate the 040 card itself...? The 040 card has its own crystal oscillator onboard. p _ the pickle The FAQ http://macfaq.binhost.com/ The Archive http://www.jmug.org/software/thepickle/ _ -- Vintage Macs is sponsored by http://lowendmac.com/ and... Small Dog Electronicshttp://www.smalldog.com | Enter To Win A | -- Canon PowerShot Digital Cameras start at $299 | Free iBook! | Support Low End Mac http://lowendmac.com/lists/support.html Vintage Macs list info: http://lowendmac.com/lists/vintagemacs.shtml The FAQ:http://macfaq.binhost.com/ Send list messages to: mailto:[EMAIL PROTECTED] To unsubscribe, email: mailto:[EMAIL PROTECTED] For digest mode, email: mailto:[EMAIL PROTECTED] Subscription questions: mailto:[EMAIL PROTECTED] Archive: http://www.mail-archive.com/vintage.macs%40mail.maclaunch.com/ Using a Mac? Free email more at Applelinks! http://www.applelinks.com
