Re: [WISPA] shielded rj45 ends
Thanks Josh, We've tried that, a bit, more than a bit, pulled to the breaking point, none of that makes a difference. We've tried multiple crimping tools. We can put a non-shielded connector on and it snaps right in. We didn't notice this issue until these last three boxes purchased in late May. That's why I ask if others have seen this. Looking at the connector under a magnifier, I can see a difference between tabs on them and other shielded and non-shielded connectors. The difference is the distance from the front of the connector to the tab's indentation made where it snaps and locks. I haven't gotten the caliper out to measure yet and can't seem to get a good picture with the camera we have here today. I will bring in a camera tomorrow and see if if I can get a picture of them side by side. It happens to NB's we've had in the field for more than a year as well. I have a few connectors from CTI left that don't have that issue. Plug in, snap, just don't like the way the ground attaches to the connector. Thank you, Dave _ From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Tuesday, July 23, 2013 4:31 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Pull the tab out a bit. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Jul 23, 2013 4:26 PM, Dave Hulsebus cont...@portative.net wrote: We found the last 3 boxes of Tough connectors we've purchased have had issues staying snapped into NanoBridges. They just won't snap in and work their way out just enough to cause failure over time. No issues with any other radio's - just NB's. Has anyone else experienced this issue ? Dave _ From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181 tel:%28509.982.2181 ) Sent: Tuesday, July 23, 2013 2:30 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Yes. There are two styles. One has no metal shielding, the other does. Both are expensive (relatively) but I'm addicted to them. I love not having to worry about how far back I strip things. Not having to worry about wires crossing when pushed into the connector (I can check them before crimping) etc. http://ezrj45.com/ezrj45plugs.php?gclid=CLSDvLWfxrgCFWXZQgodwlQANg Marsh cable stocks them. marlon From: Kevin Owen mailto:ko...@fsr.com Sent: Tuesday, July 23, 2013 11:21 AM To: WISPA General List mailto:wireless@wispa.org Subject: Re: [WISPA] shielded rj45 ends Do they support shielded cabling? Kevin From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181 tel:%28509.982.2181 ) Sent: Tuesday, July 23, 2013 11:14 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends We love the EZ-RJ45 units. Get them from Marsh Cable. It's the style where the wires go right through the ends of the connectors and the crimper crimps and cuts at the same time. HUGE time saver. marlon From: heith mailto:wi...@mncomm.com petersen Sent: Tuesday, July 23, 2013 6:50 AM To: wireless@wispa.org Subject: [WISPA] shielded rj45 ends I was curious what shielded ends members are using. I typically use the cable that Cayman wireless sells, definitely not tough cable. I prefer the UBNT tough ends as I have no issues with them, however some of my techs dread them. I have purchased some other ends in the past but at a high premium. Anyways just looking for some ideas as I am getting out voted on the tough ends. thanks heith _ ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless _ ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] shielded rj45 ends
Does it happen with any other product besides NB? It sounds to me like NB might be the issue, not the tab. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 24, 2013 at 9:29 AM, Dave Hulsebus cont...@portative.net wrote: Thanks Josh, We've tried that, a bit, more than a bit, pulled to the breaking point, none of that makes a difference. We've tried multiple crimping tools. We can put a non-shielded connector on and it snaps right in. We didn't notice this issue until these last three boxes purchased in late May. That's why I ask if others have seen this. Looking at the connector under a magnifier, I can see a difference between tabs on them and other shielded and non-shielded connectors. The difference is the distance from the front of the connector to the tab's indentation made where it snaps and locks. I haven't gotten the caliper out to measure yet and can't seem to get a good picture with the camera we have here today. I will bring in a camera tomorrow and see if if I can get a picture of them side by side. It happens to NB's we've had in the field for more than a year as well. I have a few connectors from CTI left that don't have that issue. Plug in, snap, just don't like the way the ground attaches to the connector. Thank you, Dave From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Tuesday, July 23, 2013 4:31 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Pull the tab out a bit. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Jul 23, 2013 4:26 PM, Dave Hulsebus cont...@portative.net wrote: We found the last 3 boxes of Tough connectors we've purchased have had issues staying snapped into NanoBridges. They just won't snap in and work their way out just enough to cause failure over time. No issues with any other radio's - just NB's. Has anyone else experienced this issue ? Dave From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181) Sent: Tuesday, July 23, 2013 2:30 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Yes. There are two styles. One has no metal shielding, the other does. Both are expensive (relatively) but I’m addicted to them. I love not having to worry about how far back I strip things. Not having to worry about wires crossing when pushed into the connector (I can check them before crimping) etc. http://ezrj45.com/ezrj45plugs.php?gclid=CLSDvLWfxrgCFWXZQgodwlQANg Marsh cable stocks them. marlon From: Kevin Owen Sent: Tuesday, July 23, 2013 11:21 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Do they support shielded cabling? Kevin From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181) Sent: Tuesday, July 23, 2013 11:14 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends We love the EZ-RJ45 units. Get them from Marsh Cable. It’s the style where the wires go right through the ends of the connectors and the crimper crimps and cuts at the same time. HUGE time saver. marlon From: heith petersen Sent: Tuesday, July 23, 2013 6:50 AM To: wireless@wispa.org Subject: [WISPA] shielded rj45 ends I was curious what shielded ends members are using. I typically use the cable that Cayman wireless sells, definitely not tough cable. I prefer the UBNT tough ends as I have no issues with them, however some of my techs dread them. I have purchased some other ends in the past but at a high premium. Anyways just looking for some ideas as I am getting out voted on the tough ends. thanks heith ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless
Re: [WISPA] shielded rj45 ends
No just the NB's and just the last three boxes of Tough connectors that we can tell. I am going to look at our crimpers, but we have three and they all do the same thing. -Original Message- From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Wednesday, July 24, 2013 9:34 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Does it happen with any other product besides NB? It sounds to me like NB might be the issue, not the tab. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 24, 2013 at 9:29 AM, Dave Hulsebus cont...@portative.net wrote: Thanks Josh, We've tried that, a bit, more than a bit, pulled to the breaking point, none of that makes a difference. We've tried multiple crimping tools. We can put a non-shielded connector on and it snaps right in. We didn't notice this issue until these last three boxes purchased in late May. That's why I ask if others have seen this. Looking at the connector under a magnifier, I can see a difference between tabs on them and other shielded and non-shielded connectors. The difference is the distance from the front of the connector to the tab's indentation made where it snaps and locks. I haven't gotten the caliper out to measure yet and can't seem to get a good picture with the camera we have here today. I will bring in a camera tomorrow and see if if I can get a picture of them side by side. It happens to NB's we've had in the field for more than a year as well. I have a few connectors from CTI left that don't have that issue. Plug in, snap, just don't like the way the ground attaches to the connector. Thank you, Dave From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Tuesday, July 23, 2013 4:31 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Pull the tab out a bit. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Jul 23, 2013 4:26 PM, Dave Hulsebus cont...@portative.net wrote: We found the last 3 boxes of Tough connectors we've purchased have had issues staying snapped into NanoBridges. They just won't snap in and work their way out just enough to cause failure over time. No issues with any other radio's - just NB's. Has anyone else experienced this issue ? Dave From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181) Sent: Tuesday, July 23, 2013 2:30 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Yes. There are two styles. One has no metal shielding, the other does. Both are expensive (relatively) but I'm addicted to them. I love not having to worry about how far back I strip things. Not having to worry about wires crossing when pushed into the connector (I can check them before crimping) etc. http://ezrj45.com/ezrj45plugs.php?gclid=CLSDvLWfxrgCFWXZQgodwlQANg Marsh cable stocks them. marlon From: Kevin Owen Sent: Tuesday, July 23, 2013 11:21 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Do they support shielded cabling? Kevin From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181) Sent: Tuesday, July 23, 2013 11:14 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends We love the EZ-RJ45 units. Get them from Marsh Cable. It's the style where the wires go right through the ends of the connectors and the crimper crimps and cuts at the same time. HUGE time saver. marlon From: heith petersen Sent: Tuesday, July 23, 2013 6:50 AM To: wireless@wispa.org Subject: [WISPA] shielded rj45 ends I was curious what shielded ends members are using. I typically use the cable that Cayman wireless sells, definitely not tough cable. I prefer the UBNT tough ends as I have no issues with them, however some of my techs dread them. I have purchased some other ends in the past but at a high premium. Anyways just looking for some ideas as I am getting out voted on the tough ends. thanks heith ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless
Re: [WISPA] shielded rj45 ends
We've got to pull the tab on all of the connectors we've ever used. After that it works for Trango radios/poes, Nanostations, Rockets, UBNT poe and WB surge suppressors. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 24, 2013 at 10:30 AM, Dave Hulsebus cont...@portative.net wrote: No just the NB's and just the last three boxes of Tough connectors that we can tell. I am going to look at our crimpers, but we have three and they all do the same thing. -Original Message- From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Wednesday, July 24, 2013 9:34 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Does it happen with any other product besides NB? It sounds to me like NB might be the issue, not the tab. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 24, 2013 at 9:29 AM, Dave Hulsebus cont...@portative.net wrote: Thanks Josh, We've tried that, a bit, more than a bit, pulled to the breaking point, none of that makes a difference. We've tried multiple crimping tools. We can put a non-shielded connector on and it snaps right in. We didn't notice this issue until these last three boxes purchased in late May. That's why I ask if others have seen this. Looking at the connector under a magnifier, I can see a difference between tabs on them and other shielded and non-shielded connectors. The difference is the distance from the front of the connector to the tab's indentation made where it snaps and locks. I haven't gotten the caliper out to measure yet and can't seem to get a good picture with the camera we have here today. I will bring in a camera tomorrow and see if if I can get a picture of them side by side. It happens to NB's we've had in the field for more than a year as well. I have a few connectors from CTI left that don't have that issue. Plug in, snap, just don't like the way the ground attaches to the connector. Thank you, Dave From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Josh Luthman Sent: Tuesday, July 23, 2013 4:31 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Pull the tab out a bit. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Jul 23, 2013 4:26 PM, Dave Hulsebus cont...@portative.net wrote: We found the last 3 boxes of Tough connectors we've purchased have had issues staying snapped into NanoBridges. They just won't snap in and work their way out just enough to cause failure over time. No issues with any other radio's - just NB's. Has anyone else experienced this issue ? Dave From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181) Sent: Tuesday, July 23, 2013 2:30 PM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Yes. There are two styles. One has no metal shielding, the other does. Both are expensive (relatively) but I'm addicted to them. I love not having to worry about how far back I strip things. Not having to worry about wires crossing when pushed into the connector (I can check them before crimping) etc. http://ezrj45.com/ezrj45plugs.php?gclid=CLSDvLWfxrgCFWXZQgodwlQANg Marsh cable stocks them. marlon From: Kevin Owen Sent: Tuesday, July 23, 2013 11:21 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends Do they support shielded cabling? Kevin From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Marlon Schafer (509.982.2181) Sent: Tuesday, July 23, 2013 11:14 AM To: WISPA General List Subject: Re: [WISPA] shielded rj45 ends We love the EZ-RJ45 units. Get them from Marsh Cable. It's the style where the wires go right through the ends of the connectors and the crimper crimps and cuts at the same time. HUGE time saver. marlon From: heith petersen Sent: Tuesday, July 23, 2013 6:50 AM To: wireless@wispa.org Subject: [WISPA] shielded rj45 ends I was curious what shielded ends members are using. I typically use the cable that Cayman wireless sells, definitely not tough cable. I prefer the UBNT tough ends as I have no issues with them, however some of my techs dread them. I have purchased some other ends in the past but at a high premium. Anyways just looking for some ideas as I am getting out voted on the tough ends. thanks heith ___ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless ___ Wireless mailing list Wireless@wispa.org
