Does it happen with any other product besides NB? It sounds to me like NB might be the issue, not the tab.
Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Wed, Jul 24, 2013 at 9:29 AM, Dave Hulsebus <cont...@portative.net> wrote: > Thanks Josh, > > We've tried that, a bit, more than a bit, pulled to the breaking point, none > of that makes a difference. We've tried multiple crimping tools. We can put > a non-shielded connector on and it snaps right in. We didn't notice this > issue until these last three boxes purchased in late May. That's why I ask > if others have seen this. Looking at the connector under a magnifier, I can > see a difference between tabs on them and other shielded and non-shielded > connectors. The difference is the distance from the front of the connector > to the tab's indentation made where it snaps and locks. I haven't gotten the > caliper out to measure yet and can't seem to get a good picture with the > camera we have here today. I will bring in a camera tomorrow and see if if I > can get a picture of them side by side. > > It happens to NB's we've had in the field for more than a year as well. I > have a few connectors from CTI left that don't have that issue. Plug in, > snap, just don't like the way the ground attaches to the connector. > > Thank you, > > Dave > > > > ________________________________ > From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On > Behalf Of Josh Luthman > Sent: Tuesday, July 23, 2013 4:31 PM > > To: WISPA General List > Subject: Re: [WISPA] shielded rj45 ends > > Pull the tab out a bit. > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > > On Jul 23, 2013 4:26 PM, "Dave Hulsebus" <cont...@portative.net> wrote: >> >> We found the last 3 boxes of Tough connectors we've purchased have had >> issues staying snapped into NanoBridges. They just won't snap in and work >> their way out just enough to cause failure over time. No issues with any >> other radio's - just NB's. Has anyone else experienced this issue ? >> >> Dave >> >> ________________________________ >> From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On >> Behalf Of Marlon Schafer (509.982.2181) >> Sent: Tuesday, July 23, 2013 2:30 PM >> To: WISPA General List >> Subject: Re: [WISPA] shielded rj45 ends >> >> Yes. >> >> There are two styles. One has no metal shielding, the other does. Both >> are expensive (relatively) but I’m addicted to them. I love not having to >> worry about how far back I strip things. Not having to worry about wires >> crossing when pushed into the connector (I can check them before crimping) >> etc. >> >> http://ezrj45.com/ezrj45plugs.php?gclid=CLSDvLWfxrgCFWXZQgodwlQANg >> >> Marsh cable stocks them. >> >> marlon >> >> >> From: Kevin Owen >> Sent: Tuesday, July 23, 2013 11:21 AM >> To: WISPA General List >> Subject: Re: [WISPA] shielded rj45 ends >> >> >> Do they support shielded cabling? >> >> >> >> Kevin >> >> >> >> >> >> From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On >> Behalf Of Marlon Schafer (509.982.2181) >> Sent: Tuesday, July 23, 2013 11:14 AM >> To: WISPA General List >> Subject: Re: [WISPA] shielded rj45 ends >> >> >> >> We love the EZ-RJ45 units. Get them from Marsh Cable. >> >> >> >> It’s the style where the wires go right through the ends of the connectors >> and the crimper crimps and cuts at the same time. HUGE time saver. >> >> >> >> marlon >> >> >> >> >> >> From: heith petersen >> >> Sent: Tuesday, July 23, 2013 6:50 AM >> >> To: wireless@wispa.org >> >> Subject: [WISPA] shielded rj45 ends >> >> >> >> I was curious what shielded ends members are using. I typically use the >> cable that Cayman wireless sells, definitely not tough cable. I prefer the >> UBNT tough ends as I have no issues with them, however some of my techs >> dread them. I have purchased some other ends in the past but at a high >> premium. Anyways just looking for some ideas as I am getting out voted on >> the tough ends. >> >> >> >> thanks >> >> heith >> >> ________________________________ >> >> _______________________________________________ >> Wireless mailing list >> Wireless@wispa.org >> http://lists.wispa.org/mailman/listinfo/wireless >> >> ________________________________ >> _______________________________________________ >> Wireless mailing list >> Wireless@wispa.org >> http://lists.wispa.org/mailman/listinfo/wireless >> >> >> _______________________________________________ >> Wireless mailing list >> Wireless@wispa.org >> http://lists.wispa.org/mailman/listinfo/wireless >> > > _______________________________________________ > Wireless mailing list > Wireless@wispa.org > http://lists.wispa.org/mailman/listinfo/wireless > _______________________________________________ Wireless mailing list Wireless@wispa.org http://lists.wispa.org/mailman/listinfo/wireless