[zfs-discuss] Understanding ZFS performance.
I am new to OSOL/ZFS but have just finished building my first system. I detailed the system setup here: http://opensolaris.org/jive/thread.jspa?threadID=128986tstart=15 I ended up having to add an additional controller card as two ports on the motherboard did not work as standard Sata port. Luckily I was able to salvage an LSI SAS card from an old system. Things seem to be working OK for the most part.. But I am trying to dig a bit deeper into the performance. I have done some searching and it seems that the iostat -x can help you better understand your performance. I have 8 drives in the system. 2 are in a mirrored boot pool and the other 6 are in a single raidz2 pool. All 6 are the same. Samsung 1TB Spinpoints. Here is what my output looks like from iostat -x 30 during a scrub of the raidz2 pool: devicer/sw/s kr/s kw/s wait actv svc_t %w %b cmdk0 299.71.5 37080.91.6 7.7 2.0 32.3 98 99 cmdk1 300.21.3 37083.01.5 7.7 2.0 32.2 98 99 cmdk2 1018.61.6 37141.31.7 0.5 0.71.2 22 43 cmdk3 0.01.80.05.2 0.0 0.0 33.7 1 2 cmdk4 1045.62.1 37124.31.4 0.7 0.71.3 21 41 sd6 0.01.80.05.2 0.0 0.0 25.1 0 1 sd71033.42.5 37128.51.8 0.0 1.01.0 3 38 sd81044.52.5 37129.41.8 0.0 0.90.9 3 36 extended device statistics devicer/sw/s kr/s kw/s wait actv svc_t %w %b cmdk0 301.91.3 37339.01.7 7.8 2.0 32.1 99 99 cmdk1 302.11.4 37341.01.8 7.7 2.0 32.0 99 99 cmdk2 1048.11.5 37400.41.6 0.5 0.71.1 20 42 cmdk3 0.01.50.05.1 0.0 0.0 36.5 1 2 cmdk4 1054.41.6 37363.11.5 0.7 0.61.2 20 40 sd6 0.01.50.05.1 0.0 0.0 30.4 0 1 sd71044.42.1 37404.21.7 0.0 0.90.9 3 38 sd81050.52.1 37382.81.9 0.0 0.90.9 3 36 extended device statistics devicer/sw/s kr/s kw/s wait actv svc_t %w %b cmdk0 296.31.5 36195.41.7 7.8 2.0 32.7 99 99 cmdk1 295.21.5 36230.11.8 7.7 2.0 32.5 98 98 cmdk2 987.52.0 36171.51.7 0.6 0.71.3 22 43 cmdk3 0.01.50.05.1 0.0 0.0 37.7 1 2 cmdk4 1018.32.0 36160.81.6 0.7 0.61.4 21 41 sd6 0.01.50.05.1 0.0 0.1 40.3 0 2 sd71005.32.6 36300.61.8 0.0 1.11.1 3 39 sd81016.02.5 36260.12.0 0.0 1.01.0 3 36 I think cmdk3 and sd6 are in my rpool. I tried to split the pools across the controllers for better performance. It seems to me that cmdk0 and cmdk1 are much slower than the others.. But I am not sure why or what to check next... In fact I am not even sure how I can trace back that device name to figure out which controller it is connected to. Any ideas or next steps would be appreciated. Thanks. -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
iostat -xen 1 will provide the same device names as the rest of the system (as well as show error columns). zpool status will show you which drive is in which pool. As for the controllers, cfgadm -al groups them nicely. t On 23 May 2010 03:50, Brian broco...@vt.edu wrote: I am new to OSOL/ZFS but have just finished building my first system. I detailed the system setup here: http://opensolaris.org/jive/thread.jspa?threadID=128986tstart=15 I ended up having to add an additional controller card as two ports on the motherboard did not work as standard Sata port. Luckily I was able to salvage an LSI SAS card from an old system. Things seem to be working OK for the most part.. But I am trying to dig a bit deeper into the performance. I have done some searching and it seems that the iostat -x can help you better understand your performance. I have 8 drives in the system. 2 are in a mirrored boot pool and the other 6 are in a single raidz2 pool. All 6 are the same. Samsung 1TB Spinpoints. Here is what my output looks like from iostat -x 30 during a scrub of the raidz2 pool: devicer/sw/s kr/s kw/s wait actv svc_t %w %b cmdk0 299.71.5 37080.91.6 7.7 2.0 32.3 98 99 cmdk1 300.21.3 37083.01.5 7.7 2.0 32.2 98 99 cmdk2 1018.61.6 37141.31.7 0.5 0.71.2 22 43 cmdk3 0.01.80.05.2 0.0 0.0 33.7 1 2 cmdk4 1045.62.1 37124.31.4 0.7 0.71.3 21 41 sd6 0.01.80.05.2 0.0 0.0 25.1 0 1 sd71033.42.5 37128.51.8 0.0 1.01.0 3 38 sd81044.52.5 37129.41.8 0.0 0.90.9 3 36 extended device statistics devicer/sw/s kr/s kw/s wait actv svc_t %w %b cmdk0 301.91.3 37339.01.7 7.8 2.0 32.1 99 99 cmdk1 302.11.4 37341.01.8 7.7 2.0 32.0 99 99 cmdk2 1048.11.5 37400.41.6 0.5 0.71.1 20 42 cmdk3 0.01.50.05.1 0.0 0.0 36.5 1 2 cmdk4 1054.41.6 37363.11.5 0.7 0.61.2 20 40 sd6 0.01.50.05.1 0.0 0.0 30.4 0 1 sd71044.42.1 37404.21.7 0.0 0.90.9 3 38 sd81050.52.1 37382.81.9 0.0 0.90.9 3 36 extended device statistics devicer/sw/s kr/s kw/s wait actv svc_t %w %b cmdk0 296.31.5 36195.41.7 7.8 2.0 32.7 99 99 cmdk1 295.21.5 36230.11.8 7.7 2.0 32.5 98 98 cmdk2 987.52.0 36171.51.7 0.6 0.71.3 22 43 cmdk3 0.01.50.05.1 0.0 0.0 37.7 1 2 cmdk4 1018.32.0 36160.81.6 0.7 0.61.4 21 41 sd6 0.01.50.05.1 0.0 0.1 40.3 0 2 sd71005.32.6 36300.61.8 0.0 1.11.1 3 39 sd81016.02.5 36260.12.0 0.0 1.01.0 3 36 I think cmdk3 and sd6 are in my rpool. I tried to split the pools across the controllers for better performance. It seems to me that cmdk0 and cmdk1 are much slower than the others.. But I am not sure why or what to check next... In fact I am not even sure how I can trace back that device name to figure out which controller it is connected to. Any ideas or next steps would be appreciated. Thanks. -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
Following up with some more information here: This is the output of iostat -xen 30 extended device statistics errors --- r/sw/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device 296.82.9 36640.27.5 7.8 2.0 26.16.6 99 99 0 0 0 0 c7d0 296.72.5 36618.17.5 7.8 2.0 26.16.6 99 99 0 0 0 0 c7d1 952.02.6 36689.67.1 0.5 0.80.60.8 26 46 0 0 0 0 c8d1 0.01.70.05.8 0.0 0.0 10.7 13.3 1 1 0 0 0 0 c9d0 963.72.8 36712.46.4 0.5 0.70.60.7 24 43 0 84 0 84 c9d1 0.01.70.05.8 0.0 0.00.0 22.9 0 1 0 0 0 0 c4t15d0 1000.93.7 36605.06.9 0.0 0.90.00.9 3 39 0 0 0 0 c4t16d0 1000.74.1 36579.67.5 0.0 0.90.00.9 4 37 0 0 0 0 c4t17d0 extended device statistics errors --- r/sw/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device 302.65.4 36937.5 156.3 7.7 2.0 24.96.4 98 99 0 0 0 0 c7d0 303.15.4 36879.0 156.2 7.7 2.0 24.86.4 98 99 0 0 0 0 c7d1 961.45.8 36974.3 155.6 0.5 0.80.50.8 26 47 0 0 0 0 c8d1 0.03.50.0 22.7 0.0 0.0 11.19.5 1 2 0 0 0 0 c9d0 961.15.5 37044.0 154.5 0.6 0.70.60.8 26 45 0 84 0 84 c9d1 0.03.40.0 22.7 0.0 0.00.0 13.8 0 1 0 0 0 0 c4t15d0 998.17.1 36995.6 155.4 0.0 1.00.01.0 3 40 0 0 0 0 c4t16d0 996.87.2 36954.1 156.5 0.0 0.90.00.9 4 37 0 0 0 0 c4t17d0 extended device statistics errors --- r/sw/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device 296.03.4 36583.8 155.5 7.8 2.0 26.06.6 99 99 0 0 0 0 c7d0 296.33.3 36538.6 155.5 7.8 2.0 25.96.6 99 99 0 0 0 0 c7d1 920.53.4 36649.7 155.0 0.7 0.80.70.9 29 49 0 0 0 0 c8d1 0.01.80.05.9 0.0 0.0 10.6 11.4 1 1 0 0 0 0 c9d0 948.93.3 36689.5 154.3 0.6 0.70.60.7 25 44 0 84 0 84 c9d1 0.01.80.05.9 0.0 0.00.0 26.2 0 1 0 0 0 0 c4t15d0 974.03.8 36643.4 154.7 0.0 1.00.01.0 4 41 0 0 0 0 c4t16d0 976.83.8 36634.6 155.6 0.0 1.00.01.0 4 38 0 0 0 0 c4t17d0 extended device statistics errors --- r/sw/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device 301.33.6 37353.6 151.9 7.8 2.0 25.56.5 99 99 0 0 0 0 c7d0 301.53.5 37340.0 151.8 7.8 2.0 25.46.5 99 99 0 0 0 0 c7d1 979.53.4 37466.4 151.5 0.5 0.70.50.7 24 45 0 0 0 0 c8d1 0.01.70.05.9 0.0 0.0 12.4 13.7 1 1 0 0 0 0 c9d0 995.83.4 37456.7 151.0 0.5 0.70.50.7 23 43 0 84 0 84 c9d1 0.01.80.05.9 0.0 0.00.0 23.5 0 1 0 0 0 0 c4t15d0 1022.74.0 37410.8 151.4 0.0 0.90.00.9 3 38 0 0 0 0 c4t16d0 1020.14.4 37473.8 152.0 0.0 0.90.00.9 4 38 0 0 0 0 c4t17d0 I looked at it for a while and the number of errors is not increasing.. I think that may have stemmed from when I was testing hot-plugging of the drive and disconnected it at one point. The -xen helped me determine that it was disks c7d0 and c7d1 that were slower. I then tried to look at the cache settings in format: pfexec format -e Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c4t15d0 DEFAULT cyl 19454 alt 2 hd 255 sec 63 /p...@0,0/pci1002,5...@3/pci1014,3...@0/s...@f,0 1. c4t16d0 ATA-SAMSUNG HD103SJ-0001-931.51GB /p...@0,0/pci1002,5...@3/pci1014,3...@0/s...@10,0 2. c4t17d0 ATA-SAMSUNG HD103SJ-0001-931.51GB /p...@0,0/pci1002,5...@3/pci1014,3...@0/s...@11,0 3. c7d0 SAMSUNG-S246JDWZ40807-0001-931.51GB /p...@0,0/pci-...@11/i...@0/c...@0,0 4. c7d1 SAMSUNG-S246JDWZ40807-0001-931.51GB /p...@0,0/pci-...@11/i...@0/c...@1,0 5. c8d1 SAMSUNG-S246JDWZ40807-0001-931.51GB /p...@0,0/pci-...@11/i...@1/c...@1,0 6. c9d0 DEFAULT cyl 19454 alt 2 hd 255 sec 63 /p...@0,0/pci-...@14,1/i...@1/c...@0,0 7. c9d1 SAMSUNG-S246JDWZ40806-0001-931.51GB /p...@0,0/pci-...@14,1/i...@1/c...@1,0 If I look at c4t1d0, everything is how I expect it to be: Specify disk (enter its number): 2 selecting c4t17d0 [disk formatted] /dev/dsk/c4t17d0s0 is part of active ZFS pool tank. Please see zpool(1M). FORMAT MENU: disk - select a disk type - select (define) a disk type
Re: [zfs-discuss] Understanding ZFS performance.
On Sat, 22 May 2010, Brian wrote: The -xen helped me determine that it was disks c7d0 and c7d1 that were slower. You may be right, but is not totally clear since you really need to apply a workload which is assured to consistently load the disks. I don't think that 'scrub' is necessarily best for this. Perhaps the load issued to these two disks contains more random access requests. Bob -- Bob Friesenhahn bfrie...@simple.dallas.tx.us, http://www.simplesystems.org/users/bfriesen/ GraphicsMagick Maintainer,http://www.GraphicsMagick.org/ ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
extended device statistics errors --- r/sw/s kr/s kw/s wait actv wsvc_t asvc_t %w %b s/w h/w trn tot device 296.82.9 36640.27.5 7.8 2.0 26.16.6 99 99 0 0 0 0 c7d0 296.72.5 36618.17.5 7.8 2.0 26.16.6 99 99 0 0 0 0 c7d1 952.02.6 36689.67.1 0.5 0.80.60.8 26 46 0 0 0 0 c8d1 0.01.70.05.8 0.0 0.0 10.7 13.3 1 1 0 0 0 0 c9d0 963.72.8 36712.46.4 0.5 0.70.60.7 24 43 0 84 0 84 c9d1 0.01.70.05.8 0.0 0.00.0 22.9 0 1 0 0 0 0 c4t15d0 1000.93.7 36605.06.9 0.0 0.90.00.9 3 39 0 0 0 0 c4t16d0 1000.74.1 36579.67.5 0.0 0.90.00.9 4 37 0 0 0 0 c4t17d0 Seems to me c9d1 is having a hard time. How is your zpool layout? Vennlige hilsener / Best regards roy -- Roy Sigurd Karlsbakk (+47) 97542685 r...@karlsbakk.net http://blogg.karlsbakk.net/ -- I all pedagogikk er det essensielt at pensum presenteres intelligibelt. Det er et elementært imperativ for alle pedagoger å unngå eksessiv anvendelse av idiomer med fremmed opprinnelse. I de fleste tilfeller eksisterer adekvate og relevante synonymer på norsk. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
On Sat, May 22, 2010 at 11:41 AM, Brian broco...@vt.edu wrote: If I look at c7d0, I get a message about no Alt Slice found and I don't have access to the cache settings. Not sure if this is part of my problem or not: That can happen if the controller is not using AHCI. It'll effect your performance pretty drastically too. -B -- Brandon High : bh...@freaks.com ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
Is there a way within opensolaris to detect if AHCI is being used by various controllers? I suspect you may be accurate an AHCI is not turned on. The bios for this particular motherboard is fairly confusing on the AHCI settings. The only setting I have is actually in the raid section, and it seems to let select between IDE/AHCI/RAID as an option. However, I can't tell if it applies only if one is using software RAID. If I set it to AHCI, another screen appears prior to boot that is titled AMD AHCI BIOS. However, opensolaris hangs during booting with this enabled. Is there a way from the grub menu to request opensolaris boot without the splashscreen, but instead boot with debug information printed to the console? -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
If you install Opensolaris with the AHCI settings off, then switch them on, it will fail to boot I had to reinstall with the settings correct. the best way to tell if ahci is working is to use cfgadm if you see your drives there, ahci is on if not, then you may need to reinstall with it on (for the rpool at least) On Sat, May 22, 2010 at 4:43 PM, Brian broco...@vt.edu wrote: Is there a way within opensolaris to detect if AHCI is being used by various controllers? I suspect you may be accurate an AHCI is not turned on. The bios for this particular motherboard is fairly confusing on the AHCI settings. The only setting I have is actually in the raid section, and it seems to let select between IDE/AHCI/RAID as an option. However, I can't tell if it applies only if one is using software RAID. If I set it to AHCI, another screen appears prior to boot that is titled AMD AHCI BIOS. However, opensolaris hangs during booting with this enabled. Is there a way from the grub menu to request opensolaris boot without the splashscreen, but instead boot with debug information printed to the console? -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
I am not sure I fully understand the question... It is setup as raidz2 - is that what you wanted to know? -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
Thanks - I can give reinstalling a shot. Is there anything else I should do first? Should I export my tank pool? -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
just to make sure i understand what is going on here, you have a rpool which is having performance issues, and you discovered ahci was disabled? you enabled it, and now it won't boot. correct? This happened to me and the solution was to export my storage pool and reinstall my rpool with the ahci settings on. Then i imported my storage pool and all was golden On Sat, May 22, 2010 at 5:25 PM, Brian broco...@vt.edu wrote: Thanks - I can give reinstalling a shot. Is there anything else I should do first? Should I export my tank pool? -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
On 05/23/10 08:52 AM, Thomas Burgess wrote: If you install Opensolaris with the AHCI settings off, then switch them on, it will fail to boot I had to reinstall with the settings correct. Well you probably didn't have to. Booting form the live CD and importing the pool would have put things right. -- Ian. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
On 05/23/10 08:43 AM, Brian wrote: Is there a way within opensolaris to detect if AHCI is being used by various controllers? I suspect you may be accurate an AHCI is not turned on. The bios for this particular motherboard is fairly confusing on the AHCI settings. The only setting I have is actually in the raid section, and it seems to let select between IDE/AHCI/RAID as an option. However, I can't tell if it applies only if one is using software RAID. [answered in other post] If I set it to AHCI, another screen appears prior to boot that is titled AMD AHCI BIOS. However, opensolaris hangs during booting with this enabled. Is there a way from the grub menu to request opensolaris boot without the splashscreen, but instead boot with debug information printed to the console? Just hit a key once the bar is moving. -- Ian. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
This didn't work for me. I had the exact same issue a few days ago. My motherboard had the following: Native IDE AHCI RAID Legacy IDE so naturally i chose AHCI, but it ALSO had a mode called IDE/SATA combined mode I thought i needed this to use both the ide and ant sata ports, turns out it was basically an ide emulation mode for sata, long story short i ended up with opensolaris installed in IDE mode. I had to reinstall. I tried the livecd/import method and it still failed to boot. On Sat, May 22, 2010 at 5:30 PM, Ian Collins i...@ianshome.com wrote: On 05/23/10 08:52 AM, Thomas Burgess wrote: If you install Opensolaris with the AHCI settings off, then switch them on, it will fail to boot I had to reinstall with the settings correct. Well you probably didn't have to. Booting form the live CD and importing the pool would have put things right. -- Ian. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
this old thread has info on how to switch from ide-sata mode http://opensolaris.org/jive/thread.jspa?messageID=448758#448758 On Sat, May 22, 2010 at 5:32 PM, Ian Collins i...@ianshome.com wrote: On 05/23/10 08:43 AM, Brian wrote: Is there a way within opensolaris to detect if AHCI is being used by various controllers? I suspect you may be accurate an AHCI is not turned on. The bios for this particular motherboard is fairly confusing on the AHCI settings. The only setting I have is actually in the raid section, and it seems to let select between IDE/AHCI/RAID as an option. However, I can't tell if it applies only if one is using software RAID. [answered in other post] If I set it to AHCI, another screen appears prior to boot that is titled AMD AHCI BIOS. However, opensolaris hangs during booting with this enabled. Is there a way from the grub menu to request opensolaris boot without the splashscreen, but instead boot with debug information printed to the console? Just hit a key once the bar is moving. -- Ian. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
Sometimes when it hangs on boot hitting space bar or any key won't bring it back to the command line. That is why I was wondering if there was a way to not show the splashscreen at all, and rather show what it was trying to load when it hangs. -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
Ok. What worked for me was booting with the live CD and doing: pfexec zpool import -f rpool reboot After that I was able to boot with AHCI enabled. The performance issues I was seeing are now also gone. I am getting around 100 to 110 MB/s during a scrub. Scrubs are completing in 20 minutes for 1TB of data rather than 1.2 hours. -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
GREAT, glad it worked for you! On Sat, May 22, 2010 at 7:39 PM, Brian broco...@vt.edu wrote: Ok. What worked for me was booting with the live CD and doing: pfexec zpool import -f rpool reboot After that I was able to boot with AHCI enabled. The performance issues I was seeing are now also gone. I am getting around 100 to 110 MB/s during a scrub. Scrubs are completing in 20 minutes for 1TB of data rather than 1.2 hours. -- This message posted from opensolaris.org ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
On 05/23/10 11:31 AM, Brian wrote: Sometimes when it hangs on boot hitting space bar or any key won't bring it back to the command line. That is why I was wondering if there was a way to not show the splashscreen at all, and rather show what it was trying to load when it hangs. From my /rpool/boot/grub/menu.lst: title OpenSolaris Development snv_133 Debug findroot (pool_rpool,0,a) bootfs rpool/ROOT/opensolaris kernel$ /platform/i86pc/kernel/$ISADIR/unix -kd -B $ZFS-BOOTFS module$ /platform/i86pc/$ISADIR/boot_archive The -kd drops into the kernel debugger. If all you want to do is loose the splash screen, copy your existing entry and use: kernel$ /platform/i86pc/kernel/$ISADIR/unix -B $ZFS-BOOTFS -- Ian. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
Re: [zfs-discuss] Understanding ZFS performance.
Brian wrote: Sometimes when it hangs on boot hitting space bar or any key won't bring it back to the command line. That is why I was wondering if there was a way to not show the splashscreen at all, and rather show what it was trying to load when it hangs. Look at these threads: OpenSolaris b134 Genunix site iso failing boot http://opensolaris.org/jive/thread.jspa?threadID=125445tstart=0 Build 134 Won't boot http://ko.opensolaris.org/jive/thread.jspa?threadID=125486 http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6932552 How to bypass boot splash screen? http://opensolaris.org/jive/thread.jspa?messageID=355648 They talk changing some Grub menu.lst options by either adding 'console=text' or removing 'console=graphics' . See if that works for you too. ___ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
