Hello everybody.
I have a problem with my Billion ISDN card.
When I run Asterisk (asterisk -vvvc) on five minutes (aprox.) it puts in the
screen this:
zaphfc: empty HDLC frame or bad CRC received (framelen = 3, stat = 0xff,
card = 0).
in the framelen it change 3 and 2.
Anyone knows something
Kai Fürstenberg napisał(a):
> If you want to connect a telephone to the HFC card you need a crossed
> cable to connect to an NTBA to which you connect the phones.
i'm connecting to ISDN-NTBA from T-Com.
> As far as I know you don't need a crossed cable when you connect the
> phone directly.
>
>
Hi Marcin,
Marcin J. Kowalczyk wrote:
hI,
I've got problem with zaphfc kernel module. After I load into kernel i
receive something like that into syslog:
0 16:56:42 viperprint-de kernel: zaphfc: empty HDLC frame or bad CRC
received (framelen = 5, stat = 0xff, card = 0).
Jul 10 16:56:42 viperp
hI,
I've got problem with zaphfc kernel module. After I load into kernel i
receive something like that into syslog:
0 16:56:42 viperprint-de kernel: zaphfc: empty HDLC frame or bad CRC
received (framelen = 5, stat = 0xff, card = 0).
Jul 10 16:56:42 viperprint-de kernel: zaphfc: empty HDLC frame
hello,
I patched it and now it works fine - thank you
Best regards
Andreas
On Fri, 23 Sep 2005, Johann Steinwendtner wrote:
I had the same problem. It seems that a fix into bristuff for .at
does not work very well.
I 've patched chan_zap.c
Best regards
Hans
old:
I had the same problem. It seems that a fix into bristuff for .at
does not work very well.
I 've patched chan_zap.c
Best regards
Hans
old:
} else {
if (pri->nodetype == BRI_CPE) {
/* fix for .at p2p bri lines */
p
hello,
I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a
Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and
zaphfc driver - point2point mode -.
-
| TELCO |
| BRI |
-
|
| PBX external S0
| PBX |
---
I upgraded my FC3 to kernel 2.6.11. I installed bristuff 0.2.0-RC8 and I
cannot call out using zaphfc. I can receive calls, but can't get out. Here
is what I got:
-- Starting simple switch on 'Zap/4-1'
-- Executing Dial("Zap/4-1", "Zap/1/**348|60|rTt") in new stack
> [ 00 e7 0e 12 08
Hi all,
I have a cheap ISDN card with zaphfc module in TE mode (ptmp). Everything is
going fine, I can make call from SIP phones to ISDN but sometimes while I'm
speaking (SIP -> ISDN or ISDN <-SIP) the line just break. After that I can't
dial or receive calls. Only after reloading zaphfc module
hi
> i have HFC supported ( Planet TA ) card installed on Redhat 9 and i have
> installed bristuff
> and i can load zaptel and load zaphfc module in TE mode . and unable to load
> ztdummy module properly
you don't need ztdummy if you have a zaptel card installed
> here is my zaptel.conf
>
> loa
Dear all
i have HFC supported ( Planet TA ) card installed on Redhat 9 and i have
installed bristuff
and i can load zaptel and load zaphfc module in TE mode . and unable to load
ztdummy module properly
i get this error in /var/log/asterisk/messages
Dec 17 19:00:29 ERROR[604]: Unable to load
s running?
Best regards,
Pascal.
-Ursprüngliche Nachricht-
Von: Sebastian Böhm [mailto:[EMAIL PROTECTED]
Gesendet: Dienstag, 30. November 2004 17:04
An: [EMAIL PROTECTED]
Betreff: [Asterisk-Users] zaphfc problem
Hi,
I have a problem with zaphfc in NT mode.
I installed the card, the software
Hi,
I have a problem with zaphfc in NT mode.
I installed the card, the software and made a isdn crossover cable (with
two 100Ohm resistors).
But if I pickup the phone, there is no dialtone. Also I can't ring the
phone from xlite.
if I load the zaphfc module with debug=1 I see a message when I p
Hi,
I have a partial working installation with zaphfc.
Incoming call :
For incoming call, seems work fine. But the sound is very bad with bounce
short crashing sound. Same sound with echo cancel off or on.
SDA work fine.
Another problem, it's seems that's zaphfc don't reset correctly the line.
14 matches
Mail list logo
