Well that is what I initially thought, and many a thousand less likelihood of
errors since it is either all or nothing, only potentially gaps in the
transmission for distances or fluttering from aircraft, etc. :)
Curtis Delzer
W B 6 H E F
Fessenden, North Dakota; 58438-7300
- Original Messa
They are fine. Are you talking of the sort which is a wooden sort of box with
slots in it to guide your saw?
They work best with a stiff backed saw. They do become increasingly inaccurate
because the saw tends to erode the edges of the cuts.
Put a filler board in the bottom to keep the board yo
About half the population of Michigan depends on
ground water as the primary source of drinking water.
Many of these individuals, especially those residing in
rural areas, have their own wells. In light of recent
reports of groundwater contamination in many areas of the
state, much concern exists a
A septic system should effectively accept liquid
wastes from your house and prevent biological and
nutrient contaminants from getting into your well or
nearby lakes and streams. Any, time these things do not
happen, the system is failing.
For example, when waste backs up into your home or
liquid i
What do you think of the miter boxes? Has anyone used them? Just wondering
as my mother's husband got me one.
Shane
Control of household insect pests is dependent upon
two factors; a knowledge of the pest and its habits AND
the selection of the proper management strategy, an
insecticide is not your only choice. If you choose to use
an insecticide it is important that you thoroughly
understand their different use
a rough structural engineering guide for calculating the vertical dimension
of joinsts is:
span ( in feet) / 2
+ 1
equals vertical height in inches.
so a span of 18 feet would be:
18/2 = 9, + 1 = 10 einches!
as Dale mentions, the whip of the joists is an issue. often with longer
ones, 3 inch
If you do them one sheet at a time it would just be a matter of putting the
front to the back unless you are using tongue in groove plywood. Just think
there is your shoulder workout for the day.
- Original Message -
From: Larry Stansifer
To: blindhandyman@yahoogroups.com
Sent
Hey I like that idea!
- Original Message -
From: Dan Rossi
To: blindhandyman@yahoogroups.com
Sent: Friday, January 11, 2008 11:16 AM
Subject: Re: [BlindHandyMan] Finding the centers
You've gotten good advice so far. One thing you could try for locating
the joists when yo
If your layout matches your math that is what will happen. 3/4 of an inch is
plenty enough. If you get a little hesitant you can always "scab" a 2 by 4
along side the joist. Scab is a term used to join a board along side another
when it wasn't called for in the beginning.
To make sure ther
Some nice 4 by 4s would look good and you can always put an outlet on one to
fire up the fridge.
My impact gun is a Dewalt only because I have the 18 volt batteries already.
But everyone seems to have one now. Makita makes a real nice one too with a
bit more torque than mine. You can buy t
Are you planning on using 3 inch screws to hold plywood down onto joists?
Go for something much smaller. a Twice the thickness of the plywood and maybe a
little more is plenty. Drywall screws go in just fine. any drill will run them
in.
Dale Leavens, Cochrane Ontario Canada
[EMAIL PROTECTED]
Sk
You will be lucky if there is only half an inch of deflection.
I don't know how wide a span you are forming but it is common practice to
instal cross bracing. Traditionally this is an 'X' of 2 by 2 but these usually
split when nailing and cutting the angles is a pain in the a**. it is however
c
Good point Ron...
I have heard horror story's about purchasing the best material and still
having the damn board out 1/2" or more over an 8 foot run. Would you do
something like check along the length of each joist and drive in some kind
of a stretcher board to even them out? I am used to working i
Drive a nail partially in at each end and stretch a string between. Then each
place you drive a screw hold the string away while inserting the screw. When
released the string will go back to center providing you stretch it about a
quarter or half an inch above the wood..
Ron
Not real fast but
EHT: Nobody wants a bouncy deck. When framing the deck's support system, do
you have any suggestions for a homeowner to ensure the deck remains sturdy?
DB: Always OVER-build. I use 2-by-6 for my decking but never for my framing.
The smallest joist size used by PENMARC is 2-by-8, and most of the
HI GUYS, Does any one know where a guy or woman, can get the POPULAR MECHANICS
Magazine on line or so that you can down load it like a e-book or book for the
stream??? Hope this makes sense to you... There web site is not the best as far
as I can till...
ROB FROM MINNESOTA
- Original
Dan,
for a deck or a ground level flooring project that sounds really good
however at 8 feet in the air it might be a bit of a party.
-Original Message-
From: blindhandyman@yahoogroups.com [mailto:[EMAIL PROTECTED]
On Behalf Of Dan Rossi
Sent: Friday, January 11, 2008 9:17 AM
To: blindhan
You've gotten good advice so far. One thing you could try for locating
the joists when you go to screw down the plywood. First, lay out the
plywood. Then, from underneath, stick some lines of tape on the plywood
on either side of the joists. Then flip the plywood over end over end,
making s
Make your first joist 15 3/4, then your edges of plywood at 4 foot, or 8
foot should fall in the middle of a joist. I would use 4/8 or 3/4 T&G
plywood run perpendicular to the joists.
that big I would sister 2 2x12 for the beam, and put a 6x6 in the middle.
then you only have one support pull in t
Hi Lary;
Here is my 2 cents.
> What is the best way to locate the 16" joist centers once you have the
> plywood laid out. I have a number of ideas however none of them have been
> tried and I'm not looking to reinvent any wheels.
<<< I always drive a screw half way in an each enc and run a
My vote is for joist hangers, especially if your doing it by yourself.
Michael
_
From: blindhandyman@yahoogroups.com [mailto:[EMAIL PROTECTED]
On Behalf Of Larry Stansifer
Sent: Friday, January 11, 2008 08:12
To: blindhandyman@yahoogroups.com
Subject: RE: [BlindHandyMan] Installing lo
What is the best way to locate the 16" joist centers once you have the
plywood laid out. I have a number of ideas however none of them have been
tried and I'm not looking to reinvent any wheels.
If my math is correct it will be necessary to split the third joist
thickness in order to accommodate th
Well I would suggest drilling the top board so it will be pulled tight to the
joist, or at least some of them that is a lot of drilling. Predrilling will
help to start the screws straight. The hangers are good but if they are not
spaced at the 16 on center then the joist will not be. I guess
I fired the vette last night about 11:30PM and I have a vibration in the
clutch. I think the heroes at hayse got me on the relational balancing of
the new clutch set. To-day is a work day so probably won't get back to it
until after Miller time this evening.*/%^ I hope I don't have to pull the
moto
Larry,
I have fallen in love with the best toy ... tool for sinking those long decking
screws. I have the Dewalt impact driver. You can put a drill with a quarter
inch hex shank on it and drill the hole, then switch it to a driver bit and run
anything home. It has plenty of torque and when t
Well, all the pex tubing is in place from the basement up. The floor has
been re-done and leveled for the new items. The dresser and vanity have been
exactly marked as to where they will be placed so a cloth hamper and closet can
be designed for proper placement.
The old plaster (hor
I have no idea, but...
Good start eh?
Anyway, I am thinking though, if you just use your drillpress and drill a small
piolot hole in the wood which is going to go against the wall and be screwed
into existing, studs in the wall, then, that gives you your strait hole to
start.
Then you go back wi
Hi guys,
Remember the shop loft we discussed last year that never got done for a hole
bunch of reasons none of which are good?
Well it and a couple of wood projects are about to bubble to the top in 08.
My question for all of you wood guys is, how do I sink those 3+ inch decking
screws making cer
29 matches
Mail list logo