Hey guys,
Do you all have good methods for making sure that, when you're using a
power drill or screw driver, you're holding the drill or screw driver
so that the screw or drill bit goes in completely straight and not on
an angle? I've had problems lately (just started using my portable
12V drill
Noel,
What I do when I am drilling, is I take a block that I know is nice and
square, actually, I use a 1 2 3 setup block. I stand that up next to the
spot where I want to drill, then just line up the drill bit with the edge
of the block. Once you get the drill going, you can slide the block
On Tue, 23 Jun 2009 09:39:55 -0400you write:
>
>Hey guys,
>
>Do you all have good methods for making sure that, when you're using a
>power drill or screw driver, you're holding the drill or screw driver
>so that the screw or drill bit goes in completely straight and not on
>an angle? I've had prob
: blindhandyman@yahoogroups.com
Subject: Re: [BlindHandyMan] screw driving and rilling straight
On Tue, 23 Jun 2009 09:39:55 -0400you write:
>
>Hey guys,
>
>Do you all have good methods for making sure that, when you're using a
>power drill or screw driver, you're h
: Re: [BlindHandyMan] screw driving and rilling straight
Noel,
What I do when I am drilling, is I take a block that I know is nice and
square, actually, I use a 1 2 3 setup block. I stand that up next to the
spot where I want to drill, then just line up the drill bit with the edge
of
stated.
-Original Message-
From: blindhandyman@yahoogroups.com [mailto:blindhandy...@yahoogroups.com]
On Behalf Of Noel Romey
Sent: Tuesday, June 23, 2009 2:40 PM
To: blindhandyman@yahoogroups.com
Subject: [BlindHandyMan] screw driving and rilling straight
Hey guys,
Do you all have good
screw or
> Drill bit into the Vee to hold it straight.
>
>
>
> From: blindhandyman@yahoogroups.com [mailto:blindhandy...@yahoogroups.com]
> On Behalf Of Dan Rossi
> Sent: Tuesday, June 23, 2009 11:44 AM
> To: blindhandyman@yahoogroups.com
> Subject: Re: [BlindHandyMan]
no but i hav used a bentch top drill press
- Original Message -
From: Noel Romey
To: blindhandyman@yahoogroups.com
Sent: Tuesday, June 23, 2009 7:13 PM
Subject: Re: [BlindHandyMan] screw driving and rilling straight
The only reason I can think there's a greater si
Thanks, I didn't know what all that was about.
From: blindhandyman@yahoogroups.com [mailto:blindhandy...@yahoogroups.com]
On Behalf Of Noel Romey
Sent: Tuesday, June 23, 2009 2:14 PM
To: blindhandyman@yahoogroups.com
Subject: Re: [BlindHandyMan] screw driving and rilling straight
email to,
funwithtubes-subscr...@yahoogroups.com
- Original Message -
From: "Noel Romey"
To:
Sent: Tuesday, June 23, 2009 1:13 PM
Subject: Re: [BlindHandyMan] screw driving and rilling straight
> The only reason I can think there's a greater sign is because of quot
To: blindhandyman@yahoogroups.com
Sent: Tuesday, June 23, 2009 12:57 PM
Subject: RE: [BlindHandyMan] screw driving and rilling straight
Your message is full of the greater sign. Do you know what causes that? My
screen reader is saying freater greater greater greater greater etc..
From: blindhandy
n only read the answer.
Hopefully this will answer a few questions. A lot more help could be
obtained on the blind computing list.
Moderator
- Original Message -
From: "Bob Kennedy"
To:
Sent: Tuesday, June 23, 2009 6:41 PM
Subject: Re: [BlindHandyMan] screw driving and rilling
To: blindhandyman@yahoogroups.com
Sent: Tuesday, June 23, 2009 2:39 PM
Subject: [BlindHandyMan] screw driving and rilling straight
Hey guys,
Do you all have good methods for making sure that, when you're using a
power drill or screw driver, you're holding the drill or sc
he drill press. I would then place
> the block on the job where it matters and use it as my guide
>
> Cheers.
> Jim..
> - Original Message -
> From: Noel Romey
> To: blindhandyman@yahoogroups.com
> Sent: Tuesday, June 23, 2009 2:39 PM
> Subject: [BlindHan
s.com
Sent: Wednesday, June 24, 2009 1:16 PM
Subject: Re: [BlindHandyMan] screw driving and rilling straight
Jim,
My issue is that I don't have a drill press right now. Perhaps I need
to get one at some point soon?
Noel
On 6/23/09, Jim Tosh wrote:
> Hi Noel,
> wh
x27;s no gud for
> driveing but once you hav your pilot hoale the screw wil folow
> - Original Message -
> From: Noel Romey
> To: blindhandyman@yahoogroups.com
> Sent: Wednesday, June 24, 2009 1:16 PM
> Subject: Re: [BlindHandyMan] screw driving and rilling st
Noel,
The block with a straight hole in it works O.K. but I preferr
a block with a 90 degree inside corner cut in it very accurately. You can
hold it flat on the surface to be drilled with the "V" or inside
corner near your mark. The put the point of the drill on your
mark and bring the inside co
17 matches
Mail list logo
