I want to use SUB as primary and PUB as secondary TFTP.
option 150 ip subip pubip
option 66 ip subip pubip
Which is appropriate.
On Cisco router 12.4T(22) both are supported.
What is the difference ?
TIA
Shrini
___
For more information regarding
Hi Shingei
This morning I tried this and it works after the change.
Thanks a lot for your help.
Regards
Amit
Sent from my iPhone
On 22/03/2011, at 5:43 PM, ShinGei Yong shingei.y...@gmail.com wrote:
Can you change your authentication URL to the below:
url authentication
Hi All,
earlier BLF call list in CME was working but not sure why its not working
now.
here is my config
sip-ua
presence enable
presence
presence call-list
max-subscription 120
watcher all
allow subscribe
presence enable
ephone-dn 1 dual-line
number 4000 no-reg primary
description
On CCM it is registered to right interface and right CCM.
On router sh ccm-manager returns Primary call manager registered and
backup ready.
But still I see sh isdn status as TEI_ASSIGNED
what else could be the problem ?
T I A
Shrini
___
For more
Please ignore - it was due to bad cable
On 3/21/2011 11:31 PM, Shrini wrote:
On CCM it is registered to right interface and right CCM.
On router sh ccm-manager returns Primary call manager registered and
backup ready.
But still I see sh isdn status as TEI_ASSIGNED
what else could be the
remove mgcp bindings if any and after it registers put them back, you can
also try shut, no shut the controller
On 22 March 2011 09:31, Shrini linuxbos...@gmail.com wrote:
On CCM it is registered to right interface and right CCM.
On router sh ccm-manager returns Primary call manager
Rahul,
Add directory list and reload router , its tricky.
Thanks
Shrini
On 3/21/2011 11:07 PM, Rahul Kapor wrote:
Hi All,
earlier BLF call list in CME was working but not sure why its not
working now.
here is my config
sip-ua
presence enable
presence
presence call-list
Hello Shingei,
Unfortunately there is no info concerning a BRJ in the ras messages.
In my debug, a mix of debug h225 asn1 and ras. nothing about not enough bw
just a simple DCF
Regards
Claude
-Original Message-
From: ShinGei Yong [mailto:shingei.y...@gmail.com]
Sent: Mon 3/21/2011
Hi Randoll, All,
Thanks for sharing your info.
\May I ask you to paste your sample DNS config part on your HQ RTR.
Regards,
Wael Agina
On Tue, Mar 22, 2011 at 4:31 AM, Randall Saborío Cubero
ill2...@gmail.comwrote:
I usually do all the DNS on the HQ router. The configuration is all on
is it possible you have debug condition set??? filtering the debugs in some
direction? I think you can do that with filter-list...
On Sun, Mar 20, 2011 at 10:54 AM, ShinGei Yong shingei.y...@gmail.comwrote:
Hi
I'm facing an issue, which i've BR2 GW registered with HQ UCM as H323 GW.
When i
Dear All,
What is the simplest / best way to change parameters / setting of any
image [.jpg file] photo to match the required setting needed for ip phone
background ?
I.E: i have some photos / jpg format and need to upload to cucm / cme to use
as a background, is there a specific way to use it
hi, did you configure l3 backhaul on the serial interface?
On Mar 22, 2011 8:54 AM, Shrini linuxbos...@gmail.com wrote:
On CCM it is registered to right interface and right CCM.
On router sh ccm-manager returns Primary call manager registered and
backup ready.
But still I see sh isdn status
If you need to do it quickly for testing purposesuse the phone designer
widget available on cisco website. Otherwise look at the ip phone admin guide
and use an editing program. You can't use phone designer in the lab and I
highly doubt we would ever be askes to edit a background image
Guys,Lab 5 released guys i have no words to say!!It was my 9 attempt and
again i got fucXJust to inform there was lot of things
which i got it never seen in life :)SIP Trunk , AAR , MVA , CAC all changedIPCC
page was one full page, SIP trunk troubleshooting was full
lab 5 released and i failed my 9th attempt in brusels): ): ): ): ): ):) :)___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
You might need to type the ephones too.
--
On Mar 22, 2011, at 0:07, Rahul Kapor rahul.kapo...@gmail.com wrote:
Hi All,
earlier BLF call list in CME was working but not sure why its not working
now.
here is my config
sip-ua
presence enable
presence
presence call-list
Are you serious?
Why you mail is ccievoicelab5?
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of ccievoice
Sent: Tuesday, March 22, 2011 4:38 PM
To: ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] Lab 5 released
Guys,
Lab 5
You need to go under you serial interface and do a no isdn bind-l3
ccm-manager.
Do a show isdn status again.
The do isdn bind-l3 ccm-manager
HTH
Randall
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Shrini
Sent: Monday, March
what do you mean by AAR, MVA, CAC changed
did they suddenly create new product, CALL MANAGER FROM FUTURE VERSION
2011?
if you know how to configure AAR, MVA, CAC they do not change!!
from what I understand, you've done 9 labs, and you mean that the tasks have
changed.
but if you know how to
thanks for replying
i added phone type and reloaded the router but did not help.
hi Shirini,
Please let me know exact cli reg directory
thx,
Rahul
On Tue, Mar 22, 2011 at 6:48 PM, CCIE Voice cc...@corb.net wrote:
You might need to type the ephones too.
--
On Mar 22, 2011, at 0:07, Rahul
If all else fails try a reboot
-Original Message-
From: Randall Crumm randall.cr...@flextronics.com
Sender: ccie_voice-boun...@onlinestudylist.com
Date: Tue, 22 Mar 2011 08:25:46
To: Shrinilinuxbos...@gmail.com; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP GW - sh
Hi guys,
I’m pretty new to this distribution list. Passed CCNP Voice (formerly CCVP)
recently. And planning to study on CCIE Voice.
Where can you find those blueprints you are talking about?
Cheers
De : ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] De
Thanks :)
On Tue, Mar 22, 2011 at 2:09 PM, cciefo...@hotmail.com wrote:
If you need to do it quickly for testing purposesuse the phone
designer widget available on cisco website. Otherwise look at the ip phone
admin guide and use an editing program. You can't use phone designer in the
What type of phone is it?
Thanks,
Chevy
On Mar 22, 2011 11:17 AM, Rahul Kapor rahul.kapo...@gmail.com wrote:
thanks for replying
i added phone type and reloaded the router but did not help.
hi Shirini,
Please let me know exact cli reg directory
thx,
Rahul
On Tue, Mar 22, 2011 at 6:48
I believe that the discussion of the contents of a specific CCIE lab is a
violation of NDA.
My apologies if this is inaccurate.
On Mar 22, 2011 12:17 PM, George Goglidze gogli...@gmail.com wrote:
what do you mean by AAR, MVA, CAC changed
did they suddenly create new product, CALL MANAGER
I'm sure a lot of you have seen this document, but I thought I would share
it to anyone who hasn't seen it:
http://www.cisco.com/en/US/products/hw/switches/ps5023/products_tech_note09186a0080883f9e.shtml
This document has the best descriptions of all of the 3750 QOS features I
have seen.
You can see the blueprint here:
http://www.cisco.com/web/learning/le3/ccie/voice/index.html
Regards,
On Tue, Mar 22, 2011 at 4:24 PM, MALYGA Matthieu m.mal...@spie.com wrote:
Hi guys,
I’m pretty new to this distribution list. Passed CCNP Voice (formerly CCVP)
recently. And planning to
I remember labbing in the past and my CSSs disappear off of my phones. It's
happened once or twice, and I assumed that i must have checked the wrong
thing in the BAT tool. Then I just watched Vik's video volume 10 task 2.2
and the same thing happened to him! Has anybody seen any errors like
Hi,
I'm sure you're not telling the truth.
And if after 9 attempts you dont know how to configure a SIP trunk, AAR or
CAC, you have to choose a path other than CCIE VOICE.
Please, let us work quietly.
Thanks
nizar
On Tue, Mar 22, 2011 at 12:38 PM, ccievoice
well said Nizar...i see many idiots in this mailing list now !!!
On Wed, Mar 23, 2011 at 5:23 AM, Nizar Jafri n.ja...@cbi.ma wrote:
Hi,
I'm sure you're not telling the truth.
And if after 9 attempts you don’t know how to configure a SIP trunk, AAR or
CAC, you have to choose a path other
Adam,
Yes I have seen something similar on both 7.x and 8.x when using BAT. I would
have the phones with DNs in a temporary partition, then when I wanted to move
them into pt-internal (for example), I used BAT to change the route partition.
Everything looked good, but the CallForwardAll
31 matches
Mail list logo