I'm Building my Servers and will be loading an IOS and VMWARE. I'm hoping to
get recommendations from the group on type of IOS (I've been looking at
(ubuntu-11.04-desktop-i386.iso) to load for IOS and what VMWARE product
(VMware-server-2.0.2-203138.i386.tar.gz) is easiest to use and install. I
I've got my network devices for my home lab. Now, I'm just curious as to
what kind of servers you all are using to run the CUCM, CUPS, UCCX, AND
Connection apps on VMWare. I was thinking of getting a Dell PE 1850 with
12GB ram but not sure if that will be enough. Is there major difference in
perfor
I am running my VMware ESXi on a regular PC based system with i7 CPU,
16 GB of RAM and 4 NIC's, I split up the VM on several HDD and it runs
very well, no need to spend all the money on a full server.
Heck before this setup I had them running on a KPC from Shuttle with 4
gb ram shared and a single
Use VMWare ESXi, it is free and works very well for this. I am using
it on my system and it is a quad core desktop based system. Hardest
part is the NIC's need to be specific brand, but I just added ones in
that are supported.
On Fri, Jul 15, 2011 at 9:28 AM, wrote:
> I’m Building my Servers a
Hi Tony,
I am currently running a single server with 2 quad core CPUs (and therefore
64bit - a must for ESX) and 8gb of ram. I'm running ESX and I have 1 TB of
drive space. I can run CUCM-PUB w/2-CPUs and 2GB of ram assigned. My
CUCM-SUB is set up the same way. CUPS, and CUX set up the same way. I
I run ESXi on a Dell PC that I put a $100 used quad core CPU, 8gig of memory
for next to nothing and a pair of 1TB HDDs. I can run all the servers
required for the lab without issue. I wouldn't recommend spending more than
a couple hundred on it. Save that money for the Cisco gear.
On Fri, Jul 15
tks,
pls advice, where to config codec in MGCP ?
"Since this is MGCP it is controlled in Call manager so you can
check there for your codec."
all call to PSTN is g711
On Thu, Jul 14, 2011 at 6:14 PM, Bill Lake wrote:
> I meant for the hairpin on your MVA
>
> It looks like your sending G711ulaw
Yes 7960 very well supports SIP. Its a type A SIP phone which does not
support KPML. Check out the following blog by Vik.
http://blog.ipexpert.com/tags/type-a-sip/
HTH
Regards
Nitesh
On Thu, Jul 14, 2011 at 10:51 AM, Suresh Bhandari wrote:
> SIP is supported on 7960, as I have it on my table ri
Look at the intel i7 cpu processors. They run native quads with hyperthread
and is enhanced for virtualization. I bought a dell 435mt for $550 after
cash back and coupons from the dell outlet store.
Specs:
Intel i7 cpu @2.67
9GB ram ddr3
1.5TB
Running ESXi 4.0
I bought this 2 years ago so price
One little side note, u can't run more than 1 physical CPU on the free license
of ESXi. It can have up to 8 cores if I remember right, but 1 socket
I am upgrading to a second box because I plan on messing with things like
vmotion in the future.
The new one is more than enough on it's own. Qua
This is configured in your regions for MGCP and you can verifiy it
with the debug commands
On Fri, Jul 15, 2011 at 3:02 PM, donny f wrote:
> tks,
>
> pls advice, where to config codec in MGCP ?
> "Since this is MGCP it is controlled in Call manager so you can
> check there for your codec."
>
> al
VMWare ESXi is a bare bones Hyperviser, think very thin OS install and it is
the host, your servers are Guest systems. They run as if they are on the
hardware but share resources. This is much faster and effecient than
something like VMWare workstation or VMware server but you do not have a
useab
Agreed, I built my system from scratch with a MB and CPU I got at an Intel
event (normal cost about $300), some used HDD from system upgrades I did so
no cost at all, Memory I did buy at Newegg on sale it was about $120, a DVD
drive is about $20, video again from upgrade and the two nics. I did bu
Agreed with Mark. Don't spend too much on server.
I have a single CPU HP desktop with 8G RAM, 500GB HD, and single NIC.
Vmware ESXi 4.0 with all CM, UC, PRESENCE, and UCCX on it.
On Fri, Jul 15, 2011 at 12:58 PM, Eliot Ngwa wrote:
> I've got my network devices for my home lab. Now, I'm just cur
Anyone can help me with this?
Thanks
On Thu, Jul 14, 2011 at 8:41 PM, Abel ... wrote:
> Hello everyone, I'm have this strange issue with PhoneView, for some reason
> registered phones can be remotely access from the App, a screenshot of the
> app is attached on the mail. Also this is using CME
hi ,
i configure Voiceview from CUE , it show message, but when I play gave me
error :"Playback failed" and IOexception
anyone know what i miss ?
tks
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.co
hi exp,
is IPPM can actually sending message from Phone ? (or only from CUPS web
menu)
As I only get prompt for PIN , and can't send message thtu phone.
Any guide to use and config properly ,appreaciated
tks
___
For more information regarding indust
hi,
anyone know how to do LOCALIZATIN for CUPS. (call from PSTN to CUPS
deskphone mode still show +6172x) . I expect see 2xx )
I have tried from Phone, RDP, and DP to do localization, but no luck
advice pls
tks
___
For more informatio
anyone know command for import users from UCM to CUE using CLI ?
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking for a job? Check out
www.PlatinumPlacement.com
Hi,
Can anyone tell the username & password of the CUCM in ipexpert. I m having a
seesion now..but i m stuck outside of the CUCM because of not having the
username & pass..
Thanks & Regards
Narayan Dev Sarma
___
Regarding the config- looks ok to me.
I have had problems with the phones running older firmware. I can control my
7965 registered to CME with the following firmware (which is got by
registering to UCM 7.0)
Version :
SCCP45.8-4-1S
Try this and let me know if you need further assistance.
--
Vi
21 matches
Mail list logo
