Try configure moh multicast under telephony-service.
Powered by Telkomsel BlackBerry®
-Original Message-
From: Angel Perez
Date: Tue, 23 Mar 2010 15:21:14
To: ; osl osl
Subject: Re: [OSL | CCIE_Voice] BACD stupid problem, it's driving me nuts
___
this port is failure. I had same problem with you. I reported this to after
hour support & they move me to new POD which i usually get, POD 21 which is the
perfect one.
yesterday i got POD 23, all T1 ports for PSTN, Conf & Transcoder had problem
and got same error message "Port host processor n
in order to join 2 different call leg (sip & h323) with g729 codec, i think
transcoder (MTP hardware)is a must. MTP software can do this but only for g711
codec.
- Original Message
From: Kapil Atrish <[EMAIL PROTECTED]>
To: Edi Hamlet <[EMAIL PROTECTED]
try to terminate your call from CME to IPIPGW (w/transocder) on HQ router,
don't direct to CCM. so the topology will looks like this
IP Phone -- CME -- SIP/H323 Trunk -- IPIPGW -- SIP/H323 trunk -- CCM -- IP Phone
- Original Message
From: Kapil Atrish <[EMAIL PROTECTED]>
To: ccie_voic
Hi Parker,
i think the cfw in alias will work if the PSTN accept 1212225 and pass it
to HQ gateway. if the PSTN only accept 12122251xxx, then the cfw in alias will
not work. i think the workaround if still want using alias is put cfw
912122251xxx which is not already used in HQ, then use tr
If COR is assign to incoming dial-peer (cor incoming) & outgoing dial-peer (cor
outgoing), the COR will take affect event when the gateway is not in SRST mode.
My suggestions are:
1. Do configure outgoing dial-peer to PSTN with COR
2. Do not configure incoming dial-peer from CCM with COR
3. Let t
I also had same problem with once...
try do disable all the port
!
set port disable 7/2-4
!
then change dhcp enable to static for each port
!
set port voice interface 7/2 dhcp disable 10.10.10.1/24 gateway 10.10.10.10
tftp 10.10.10.10 dns cisco.com
!
then change back static to dhcp enable
!
set
document page-24, the
root cause of problem was I set the param welcome-prompt with
en_bacd_welcome.au. After change to _bacd_welcome.au everything was going fine.
Hope this help.
cheers,
- Original Message
From: "Kumar, Narinder" <[EMAIL PROTECTED]>
To: Edi Hamlet &
: "Kumar, Narinder" <[EMAIL PROTECTED]>
To: Edi Hamlet <[EMAIL PROTECTED]>; "ccie_voice@onlinestudylist.com"
Sent: Friday, October 3, 2008 10:16:48 AM
Subject: RE: [OSL | CCIE_Voice] BACD Issue
Initially I had “_bacd_welcome.au” instead of “en_bacd_welcome
you should strip you welcome prompt name in param welcome-prompt to
_bacd_welcome.au instead of en_bacd_welcome.au
- Original Message
From: "Kumar, Narinder" <[EMAIL PROTECTED]>
To: "ccie_voice@onlinestudylist.com"
Sent: Friday, October 3, 2008 8:51:06 AM
Subject: [OSL | CCIE_Voice]
yesterday i could access vLecture - Campus QoS series @
http://ipexpert.acrobat.com/p16754145/
But now i could not access it anymore. Does anybody know where is it moved?
Hi Mark,
in section 26 (multiprotocol challenge I) point 23, tell us to configure:
"call originating from both HQ & BR1 destined for BR2 should be routed first to
HQ-RTR gatekeeper while terminating RTP steram at IPIPGW, with appropriate
local gateway as backup. User must be able to dial BR2
Hi Mark,
in section 26 (multiprotocol challenge I) point 23, tell us to configure:
"call originating from both HQ & BR1 destined for BR2 should be routed first to
HQ-RTR gatekeeper while terminating RTP steram at IPIPGW, with appropriate
local gateway as backup. User must be able to dial BR2 u
try add this
!
application
service aa flash:app-b-acd-aa-2.0.0.0.tcl
param voicemail ! this is your voicemail number or can be any reachable
ephone-dn number
!
hope it helps
- Original Message
From: Paul and Bobs <[EMAIL PROTECTED]>
To: ccie_voice@onlinestudylist.com
Sent:
14 matches
Mail list logo