Hello,
I have been recently placed in the awkward position of making some changes
to our BGP configuration. The problem is that I understand how bgp
works for the main part, but I don't have any information on the meaning
of the symbols used in the following as-path access-lists (^, $, _,
., +,
Hello,
I was wondering if anyone knows a site that would have a graphical map
of the ISP's showing how they are connected? Of course I don't expect
the map to have every connection, but I was hoping for a basic map
showing how the ISP's are interconnected.
I was also wondering if someone knew a
Hello,
Does anyone have any suggestions for a good CBT or Book or something to
learn more about BGP? I read a book on BGP, but it talked about
confederations, communities and bgp in general. The ACRC book I have
only grazes the subject I was hoping for a book or something that would
go more in
Hello,
Have you tried clear the ARP cache. I had a similar problem and
I solved it by clearing the ARP cache. My problem wasn't with NAT,
but your problem might be solved in the same way. Good luck, I hope
this helps!
Andre
hao vu wrote:
You
might try to back out to 11.4I
had the some NAT is
Hello,
I was told that when you're working with NI1 & DMS100 you need your LDN.
ex: isdn spid1 80856532230101 5653223 <--This is working config for one of
our routers spids.
In your case the Spid's show valid, so I don't think this is the problem,
but it couldn't hurt to try it. After making th
Hello,
Is HSRP supported on 2600 series routers? In particular, I'm wondering
about the 2611. I don't see anything in my router for configuring
HSRP! Am I looking in the wrong place? Can I download an IOS image
that supports it on the 2600 series router?
Thank You,
Andre Fecteau
Hello,
Which of these do I have to have configured for my DSL to work? I need
to know what information (parameters) to ask my DSL provider for. This
is a Cisco 675 ADSL router.
SET INTERFACE WANx requires one of the following arguments
baseSet the combined VPI/VCI base value
baud
Hello,
I need:
Min: 1Fast Ethernet port
Min: 1DS3(T3) port 45Mbps
unchannelized
A CAM big enough to accomodate these high speeds.
I heard the 7020 & 7040 have the ability to use a T3(Route Switch
Processor) and FE (no scalability from there, but that's OK). How will
the performance compare to u
Hello,
I have an ADSL 675 router and the settings show 1, ?, ?, 8. But the ISP
show 0 for the VPI. How do I get around this, cause I don't see 0 as an
option?
Thanks,
Andre
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
R
Hello,
I'm trying to get my Cisco 675 to run and I can't get it to synch
up. The light on the WAN side keeps blinking. Does anyone have
any idea what I can do to get this to work? The eth0 works, but WAN0
just keeps blinking.
If I have the upload and download speed set faster than what I'm sup
Hello,
Can I put a 677 Firmware on a 675 router? The 675 uses CAP and the 677
uses DMT! I want my DSL router to use DMT!
Thanks,
Andre
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure vio
Hello Everyone,
I have a question regarding the use of FTP over IPSec. I have IPSec running
from a 3640 router to a 7206. I can do just about every IP service with no
problem except FTP. I say just about because I haven't tested SSH & a
couple others yet. Here's the problem when I run FTP cli
data will be crossing, and there are already enough hops.
Also does anyone know if NAT uses Process switching, Fast switching or
what by default? I'm inclined to say Process, but I'm not sure?
Thank You,
Andre
--
Andre Fecteau
Unix Software Engineer
[EMAIL PROTEC
Hello,
I have two locations connected by a T1 and ISDN(BRI). The T1 is
the main and the BRI is
meant as backup for just in case the T1 fails for some reason.
I have EIGRP running
between the T1 with a private addressing scheme. I have a default
route leading out through
the BRI interface with
= 0, usid = 40, tid = 1
TEI 74, ces = 2, state
= 4(await init)
spid2 configured, spid2 sent, spid2 NOT valid
Layer 3 Status:
0 Active Layer 3 Call(s)
Activated dsl 8 CCBs = 0
The Free Channel Mask: 0x8003
Help!
Andre
--
Andre Fecteau
Unix Software Engin
Hello,
Does anyone know what software you use with Windows media server to
stream audio, video live? Netshow? I tried on
demand producer, but it doesn't seem to do live content! Any push
in the right direction would be appreciated!!
Source
Remote
16 matches
Mail list logo