It will also depend on how test was carried out.
To determine the real transfer rate you must run multiple sessions with
different destinations. Many FTP site may limit per session traffic.
-Makarand
At 09:31 PM 11/20/01 -0500, you wrote:
I agree with Scott, however, you have to examine the
Cisco 2600 series does not support NM-4T, incidentally Cisco 3600 series
can not accept WIC-2
At 11:17 AM 9/4/01 -0400, Daniel Cotts wrote:
I don't believe that the NM-4T= four port serial module will work in any
2600 series router. Folks here on the list have mentioned using two WIC-2T=
Hi,
You may want to take a look at this..
http://www.maximized.com/freeware/tcpspeed/
At 07:38 AM 8/22/01 -0400, Milan Saxena wrote:
Sanjeev,
Thanks I was having a similar problema nd was wondering where to look in
for. If you get any clues, do let me know.
Thanks.
Message Posted at:
How about Inverse Mux?
Santosh Koshy wrote:
Hi All,
I have a slight dilemma to which I cannot seem to find a definitive
answer.. We have 4 circuits going from Canada to the US...
Is it necessary to terminate all the circuits into one router to do
per-packet load balancing.
--
Does your ISP support Multilink? As it seems it does not allow you to form
a Multilink
bundle.
Winway wrote:
Hi,all
cisco 2610, 3 BRIs, I use it to connect to Internet.
I configure the interfaces like this,
Interface BRI1/0
no ip address
ip nat outside
encapsulation ppp
dialer
Hi,
You may want to take a look at --
http://www.cisco.com/warp/public/793/access_dial/mpp_serial.html
Please watch the line wrap.
Matt Goodhue wrote:
Hello,
We have a Cisco2621 with two T1 going to the same place. Does anyone have
a
link to some IOS examples that would allow them to
Hi,
Which IOS you are using??
I read that from IOS 12.2 onwards it supports FR switching on ISDN.
adarsh singh wrote:
Hi
Needs some insight if you can provide .
My set up is like
router(1)
BRI--isdn-(BRI)router(2)Serail---FR
It would depend upon the routing policies -- dynamic or static at each stage.
At 01:29 AM 3/30/01 -0800, pratik shah wrote:
I have some trace of the route in a network.
Here every stage it is giving multiple paths. How
would I know that which hope is actually taken at each
stage ?
thanks
Hi,
3640 and above can support 4 FE ports, that to 3640 can support only 4 FE
ports. for that you can use -- NM2FE2W
-Mak
At 09:20 AM 2/4/00 +0800, Johnny Sun wrote:
Hi,
Use "Cisco 3620" plus two "NM-2FE2W" module,so you get 4 fastethernet ports
and 4 wan interface card slots.
But in fact
Hi,
You may use 3600 and 2500. Let voice backhaul throu FE of 3600s for both end.
On 2500 you may want to config for QoS.
On 2500 you would use standard cables, if connecting back to back then DTE and DCE
cables. For VIC-2FXS it is usual RJ-11.
Bye
-Mak
Gene Park wrote:
Hi, members,
I
Hey Gang,
Please check the URL,
http://www.cisco.com/pcgi-bin/lm/buffer/offer/dwdm/a/1406_dwdm_jump/L520-166X1
watch the line wrap.
Enjoy!!
-Mak
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and
Gang,
Please chk the url--
http://www.cisco.com/pcgi-bin/lm/buffer/offer/layer3/b/1427_jump/L542-166XX
Please watch the line wrap.
___
GO.com Mail
Get Your Free, Private E-mail at http://mail.go.com
Hi,
Please take a look at itprc.com
"ANIL.YADAV" wrote:
hi
can u please send me any article on snmp, which gives complete
detail about it.
if u know url please forward it to me.
thanks in advance!
thanks
anil
**NOTE: New CCNA/CCDA List has been formed. For more information go to
Darren House wrote:
I thought you could only get per packet load sharing by using CEF. All
other switching methods allowed for per destination/session load sharing.
I also think (I could be wrong) that if you have E0 process switched and
E1 Fast Switched, the first packet would be process
You have full duplex 64kbps channel to internet through your ISP.
So you have on Tx side a pipe of 64kbps and on Rx side a pipe of 64 kbps.
HTH
NRS Hariharan wrote:
Hi all,
I have a doubt.Iam having a 64 kbps RF leased link to my ISP .When
using the " show interface serial 0"
It is the economy to be blamed rather than thing else.
Raymond Thomas wrote:
You are absolutely right, but I never placed anyone out on contract =) I
know, I know, that's besides the point, but here is my point: You can't look
at these guys bad personally. If you needed to survive and
Want to share this with you.
Could be usefull.
-Mak
Original Message
Subject: ICMP Usage In Scanning - Research Paper
Date: Sun, 2 Jul 2000 00:42:09 +0200
From: Ofir Arkin [EMAIL PROTECTED]
Reply-To: Ofir Arkin [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
I have finished a
"cisco.groupstudy.com" wrote:
How can I get a Cisco router to chop up large packets of one protocol type
(say FTP) coming in on a LAN interface so that smaller packets of some
other, higher-priority protocol can be interleaved on an outgoing WAN
interface that they share?
You can use
Check the URL
http://www.lucent-networkcare.com/scripts/registration/registeruser.asp?regtypeid=29
Please watch the wrap.
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info:
Chandrakant chowgule wrote:
Hi all ,
I have some fundamental doubts about the E1/PRI and E1/R2 services
terminating on Access Server ( e.g AS5300 ) . To receive analog modem calls
on e1/PRi or R2 , do the access server neccesarily have modem cards with (
e.g MICA modems cards in other
Take a look at TTCP --
http://www.ccci.com/tools/ttcp/index.html
useful for IP based networks though.
From Ganymede --
http://www.qcheck.net/
Michael Fountain wrote:
This is slightly off topic, but does anyone know of a good, and preferably
free :), utility that can measure the
tour twice, HTML Flash, and never was asked to
register, nor was a book mentioned. =(
-Original Message-
From: Makarand Yerawadekar [mailto:[EMAIL PROTECTED]]
Sent: Friday, May 19, 2000 6:45 AM
To: JoeFerg
Cc: [EMAIL PROTECTED]
Subject: Re: Free Book: CCN
Go thru the e-t
Dear Gang,
Please check the URL --
http://www.cisco.com/offer/content/etour/1269_core_html/1269_portal_home.html
Please watch the line wrap.
___
GO Network Mail
Get Your Free, Private E-mail at
Dear Gang,
Please check the following URL --
http://www.cisco.com/pcgi-bin/lm/buffer/offer/networkagility/1276_landing/L319-166XD
please watch the wrap.
Bye
-Mak
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives,
24 matches
Mail list logo