Hello, everybody
Now i am confusing about the burst in CAR and GTS.
In CAR, it say that
rate-limit output bps burst-normal burst-max ...
In GTS
traffic-shape group access-list bit-rate [burst-size [excess-burst-size]]
I think that bps in CAR is the same thing as the bit-rate in GTS, and
burs
No i have primary ISDN on center. I want to use it just for dial-in. And the
dial-in user use his ip address, that not using ip pool; and don't
authentication.
Even it can dial up, but cannot ping each other. I open the debug of dialer
Can you give me a sample?
Must it have 'dialer-gourp' command
Hi, i just passed the 350-001 written exam by 84% last friday. Now i want to
prepair the lab exam now,any suggestion are welcome.
Thanks.
Message Posted at:
http://www.groupstudy.com/form/read.php?f=7&i=4342&t=4342
--
FAQ, list archives, and subs
Hello.
I have a NM-2CE1B. But what i rent is unbalance E1.
I saw in the CISCO Document CD that
"Jumpers on CE1/PRI modules can be used to connect or disconnect receive
shield to ground. (See Table 8-1.) The default setting for balanced, 120-ohm
CE1/PRI-B modules disconnects receive shield to groun
Now i have a pri in my network,but it doesnot work. Please help me. Thanks.
The following message is:
show isdn status
Global ISDN Switchtype = primary-net5
ISDN Serial0/0:15 interface
dsl 0, interface ISDN Switchtype = primary-net5
Layer 1 Status:
ACTIVE
Layer 2 Status:
The following is a sample from CISCO Document CD about Token ISL, i have one
question about it that can the VLAN 40 and 50 communication each other? The
answer i think is Yes, because they are source route bridge by the ring 101
in router. Am i right? Thanks.
This is the configuration about the r
hould i config?
"Brian" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
> On Tue, 5 Dec 2000, vtam wrote:
>
> > But the route table is learn through dynamic routing, so i cannot
specify
> > the next_hop. So are there any
But the route table is learn through dynamic routing, so i cannot specify
the next_hop. So are there any solution? Thanks.
"Brian" <[EMAIL PROTECTED]> wrote in message
[EMAIL PROTECTED]">news:[EMAIL PROTECTED]...
>
> vtam,
>
> You must specify multipl
I don't really know how the policy routing run.
This is my quetion: i want to apply policy routing according to the source,
but when the set next-hop is not accessible, it should be route as normal
routing process( route according to dest. ip address).
This is the config i do.
int ser 1/0
ip pol
The space is the books. Because it said it match all the AS_paths that start
with 1 and of length 2, such as AS_path=1, =1 10, =1 200, etc. As you said,
? # 0 or 1 of the preceding characters (in this case a space). So if ?=0, it
is ^1[0-9]*$; if ?=1, it is ^1 [0-9]*$.
Do i misread your meaning?
In the book "Internet Architectures" by Hassam, it said that ^1 ?[0-9]*$
identify all the AS_paths that start with 1 and of length 2-that is, AS1 and
its direct customs. But i think that ? means 0 or 1 occurrences, when it is
0, the expression can be equal ^1[0-9]*$,means any single AS number star
Now i have two route sent to a eigrp neigbor, there are 23.125.0.0/19 and
23.125.0.0/16, i want the receiver just selete the 23.125.0.0/16 route. I
cannot do summary in the output way, how can i do filter in the receiver?
Thanks.
_
FAQ, list archives, and subscrip
I have one 7507 as CIP, one 7505 and one IBM 2216 as DLSw+ peer, all of them
are connect to two tokenring. There are some traffic between the 2216 and
7505. I don't want the traffic bridged by the CIPs as it connect to the two
ring? What i can do in the cisco router? Thanks.
Now i want to buy a 1720 that can support sdlc, dlsw+, eigrp. When i try to
find the proper IOS, i was confused by the mean. In cisco web page, it is no
clear that can it support dlsw+, it just say support dlsw+ enhancement.
So i choose the IOS IP/IPX/AT/IBM, is it right?
How about IP PLUS? How ca
It is possible to set serveral source-bridge ring-group in one router. So if
i enable DLSw+, which ring-group is concern in dlsw+?
Thanks.
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/guide.html
FAQ, list archives, and subscription info: http://w
ontroller E1 3/1
> channel-group 1 timeslots 1-15
> channel-group 17 timeslots 17
> channel-group 18 timeslots 18
>
> and we have 3 subinterfaces of 960Kbps, 64Kbps, 64Kbps respectively.
>
> Hope this helps and not long enough to make it more confusing :-)
>
>
There are several E1 standard like Channelized E1, Fractional E1, Full rate
E1. What is the different between them? And can i use channelized E1 card
to connect Fractional E1, Full rate E1? Thanks.
___
UPDATED Posting Guidelines: http://www.groupstudy.com/list/gu
gure 'async default routing'
>
>
> --- vtam <[EMAIL PROTECTED]> wrote:
> > The following is the 3620 config:
> >
> > interface Loopback0
> > ip address 40.126.249.1 255.255.255.255
> > no ip directed-broadcast
> >
> > interface
The following is the 3620 config:
interface Loopback0
ip address 40.126.249.1 255.255.255.255
no ip directed-broadcast
interface Serial0/0
physical-layer async
ip unnumbered Loopback0
no ip directed-broadcast
encapsulation ppp
dialer in-band
dialer string 3398102
dialer-group 1
async m
I have a 3640 as dial access server as backup,using unnumber ip. Usually the
branch 3620 connect to the 7500 through DDN, when the DDN down, 3620 dial to
3640.The routing protocol is eigrp.When use DDN, 7500 can learn the 3620
route.But when use dial,the problem occur. 3640 cannot learn the ip ro
I have a channelized E1 connect to 7507, and timeslot 1 connect to 2611.
When i shutdown the e1 timeslot 1, does the 2611 ddn port cd signal would go
down?
If it is a leased line(no e1) between them, what happen? Thanks
___
FAQ, list archives, and subscription inf
21 matches
Mail list logo