I think no. I have only found that SFP to do 1Gbps on any platform.
On Sep 13, 2015, at 1:27 PM, Robert Hass
mailto:robh...@gmail.com>> wrote:
EXTERNAL
Hi
I have question are speeds 10M and 100M supported on GLC-T SFP (RJ45
10/100/1000) on Catalyst 6880 ?
Rob
_
Erm, nevermind. My lack of connectivity was due to a routing protocol issue.
The scenario below seems to work (at least in GNS3)
On May 14, 2014, at 9:16 PM, Hughes, Scott GRE-MG wrote:
> Hello,
>
> I have a router terminating two tunnels, one is a regular IPsec tunnel, and
>
Hello,
I have a router terminating two tunnels, one is a regular IPsec tunnel, and one
is a GRE tunnel with IPsec protection. Both tunnels work by themselves, but
they cannot communicate with each other.
I remember reading somewhere that you cannot hairpin an IPsec tunnel to a DMVPN
tunnel, an
In ACS 5.2, you can configure an "Identity Store Sequence" which will
authentication via RSA, and then pull additional attributes from AD (like group
membership). Your usernames need to match between systems.
You can then send back RADIUS attributes to your ASA based on AD group
membership.
Ho
Have you seen the 819 routers?
http://www.cisco.com/en/US/products/ps11615/index.html
On Jul 19, 2012, at 7:23 PM, "Rusty Dekema" wrote:
> Good evening,
>
> This question is a bit far afield for this list, but I need a reliable,
> quiet-or-silent, low-power-consumption Cisco router with tw
I'm trying to get a Cisco IOS router to enroll with a Windows 2008 R2-based CA.
I'm partially successful.
What I'd like to do:
1. Router enrolls via SCEP, no challenge password required.
2. Certificate goes into "pending" status and approved by a certificate manager
3. Router can automatically re
OSPF doesn't run on the failover.. Is that causing you issues?
On Oct 14, 2011, at 6:49 PM, "Jeff Kell" wrote:
> Just finished configuration/installation of a secondary FWSM for
> failover (active/standby), but it is not behaving as expected (I have
> ASAs in similar configurations). There ar
Did you setup any zone-pairs involving the 'self' zone? If you don't use self
zones, no additional configuration should be necessary for DHCP packets.
On Sep 12, 2011, at 9:43 AM, "Scott Voll" wrote:
> So I'm setting up a GRE IPSEC tunnel as my backup link with a 2821. I have
> also setup Z
I think RANCID is available in EPEL for RHEL, which is a product of the Fedora
project.
http://fedoraproject.org/wiki/EPEL
There's also a few other useful things in there for network/Cisco types
(netdisco comes to mind).
On May 29, 2011, at 3:46 PM, "Keegan Holley" wrote:
> Yea, that's w
Try using tcp port 400x instead of port 200x.
On Mar 24, 2011, at 9:17 PM, "Chubby" wrote:
> Hi Andrew,
>
> This is a reverse telnet session that communicate using Serial <> TCP
>
> 0xFF is part of data payload, and I can not find a way to double the content
> of payload ie: "0xFF 0xFF"
>
We use the CEM modules. They are quite cool. We use them to provide DR
for analog T1's. I wrote a small tutorial.
http://www.scotthughes.org/cem-failover
2 things to consider:
-The cards don't work in the G2 (3945, etc) ISR routers. Haven't tried
it, but that's what I've been told.
-Ask you
You need to setup a "superscope" on the windows box that includes both
the primary and secondary subnets. Even if you don't hand out any
addresses in the primary subnet, it needs to exist and bound to the
same superscope as your secondary subnet.
Sent from my iPhone.
On Nov 3, 2009, at 11:1
Netdisco does a tremendous job of hardware inventory. It discovers new
devices via CDP and stores it's data in a database. It knows about
blades, wics, and NM modules (with serial numbers for all)
http://www.netdisco.org
Sent from my iPhone.
On Sep 29, 2009, at 5:39 PM, "omar parihuana"
w
trying to avoid)
-Original Message-
From: Lars Lystrup Christensen [mailto:l...@dansketelecom.com]
Sent: Friday, July 24, 2009 3:36 PM
To: Hughes, Scott GRE/MG; cisco-nsp@puck.nether.net
Subject: RE: [c-nsp] VRF-aware Circuit emulation?
Hi Scott,
To some degree, this would be rather odd to do as CE
Does anyone know if Circuit emulation using NM-CEM-4TE1 cards supports the
xconnects inside a VRF?
Scott
NOTICE TO RECIPIENT: The information contained in this message from
Great River Energy and any attachments are confidential and intended
only for the named recipient(s). If you have received t
Yes, you need to install to a different (non-existing) directory for the new
image.
The 'install bind' *should* do the work of adding the proper boot commands.
If you have dual-supervisors, you can simply force a switchover instead of a
full reload for decreased downtime. If you have dual-super
Websvn is very slick. RSS feeds, colorized diffs.
On Jun 26, 2009, at 8:04 AM, "Ryan West" wrote:
> If you're ever run a ./configure script on a *nix system, you'll be
> more than qualified to install RANCID. It's pretty straightforward.
>
> I'm curious to see what others are using for a fro
I had this problem as well, and was able to solve it with the following config:
mls flow ip interface-full
From: cisco-nsp-boun...@puck.nether.net [cisco-nsp-boun...@puck.nether.net] On
Behalf Of ML [...@kenweb.org]
Sent: Thursday, June 18, 2009 7:36 PM
We have recently noticed a few of our 3200 routers spouting weird things to the
log. No debugs are turned on, and no changes have been made lately..
Oddly, the times between the messages are 2 hours almost to the second.
Anyone ever seen this before?
Mar 20 03:01:51: PTABLE.0[0x1F]:
Mar 20 0
19 matches
Mail list logo