Currently reading Dewey Lambdin. Not the easiest to read but his books are
rapidly climbing to the top of favorites list. I also enjoy anything written by
James L. Nelson. And there are always the traditional picks of C. S. Forester,
Alexander Kent, and Patrick O’Brian. For a change of pace, I l
I like the Ultra Safety Systems bilge switches.
http://www.tefgel.com/contain.php?param=pumpswitch_price
Dennis C.
Touche' 35-1 #83
Mandeville, LA
On Sat, Jan 2, 2016 at 10:15 PM, Ted Drossos via CnC-List <
cnc-list@cnc-list.com> wrote:
> When I was looking to replace my automatic bilge pump sw
When I was looking to replace my automatic bilge pump switch, the Water Witch
was high on my list of choices until I read this note on the Water Witch
website.
Chuck
For my two bits, Sterling Hayden wrote some damn fine books. They lit me up!
Rick
Paikea 37+
Poulsbo, WA (damn it’s cold)
> On Dec 31, 2015, at 12:58 PM, Dave via CnC-List wrote:
>
> Whynott - a new one for the list- thanks. wanderer is great, re read many
> times. Sterling Hayden wa
That's what I use for a check valve too. Nobody
ever blamed us for being conventional and no mention of wise either. :)
I have a Whale low profile stuffed way down below
the mast as well. It dries the bilge much better than the old system.
http://www.westmarine.com/buy/whale-pumps--super-sub
I bought a check valve from Grainger plumbing five years ago a d wouldn't look
back. Keep your bilge clean and you won't have a problem. Installed right
next to bilge pump so access easy.
Raise switch a little, put in che Ck valve. Done.
Bill Walker
CnC 36
Sent from AOL Mobile Mail
On Satu
Raising it doesn't help. Just more water in the bilge. The pump is a Whale.
Joel
On Saturday, January 2, 2016, Sailnomad via CnC-List
wrote:
> You can do one of the following:
> - Raise the mounting of the water witch.
> - Use a smaller diameter, or shorter hose
>
> Check valves are designed fo
You can do one of the following:
- Raise the mounting of the water witch.
- Use a smaller diameter, or shorter hose
Check valves are designed for preventing instantaneous backflow.
Pretty much all of them will eventually leak the water back into the bilge,
so you will still cycle, only with a long
Despite the "conventional wisdom" against check valves in bilge discharges,
I've had one in Touche' for a decade and a half with no issues whatsoever.
I think the secret is the type of check valve one installs. Jabsco, Whale
and Bosworth make check valves for bilge discharges. I have this one:
ht
I think that there is general consensus that a check valve in a bilge pump hose
is not a good thing.
But honestly I don’t have a good solution for avoiding the water coming back.
Marek
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of S Thomas via
CnC-List
Sent: Satur
Thank you! Unbelievably scary and beautiful the same time.
Leslie.
On Thu, 12/31/15, Marek Dziedzic via CnC-List wrote:
Subject: Stus-List Interesting photos of waves on L. Erie
To: "C&C List"
Cc: "Marek Dziedzic"
Date: Thursday, December 31,
While it would not be my choice, if you do decide to install a check valve,
install it where you can get at it. They do stick shut sometimes, and for no
obvious reason. Happened on a boat that I was crewing off the west coast of
Vancouver Island. Nearly changed out the electric pump before we th
Don't know how big the hose is, but smaller would leave less to drain. I also
have an electronic switch, - it is pumped through a Whale diaphragm pump,
which doesn't seem to allow much drain back. It is also not high volume, so
an additional centrifugal pump is also helpful.
Bill
Can you raise up the Water Witch switch so it is
several inches above the water that drains back into the bilge?
We recently installed the same switch in a Catalina 400 to
eliminate the problem you have. The advantage of the Water Witch
is that it keeps ru
Yup. Two dinghy's;
Local AIB RIB with a not-to-be removed (I like my back) 8hp 4 cycle for local
semi-controlled conditions. As in, if its that bad out, I am not leaving
anyway.High pressure floor Avon with a very movable 4hp 2 cycle for Gulf of
Maine or heading down to the Chesapeake offshore
I replaced my automatic bilge pump switch with a waterwhich. When the when
the switch activates the bilge pump, the bilge is pumped relatively dry.
However when the pump shuts off water flows back into the bilge and so the
pump is running in an endless loop. I see my alternatives as installing a
ch
I do have some store bought plastic trays in there. The tools are loose, it's
just the ones I use all the time; screwdrivers, adjustable wrench, pliers a
cheap, basic socket set and a hammer.
I'll get some pics next time I'm up at the boat.
Andy
C&C 40
Peregrine
Andrew Burton
61 W Narragansett
On my 29, there are two screw holes in the mast where it attaches. Do you see
screw holes on yours?
Original Message
From: Mike Brannon
Sent: Saturday, January 2, 2016 09:04
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Cabin Folding Table
Tom, the table in my 78 was also attached to the
Andy; great ideadid you put some sort of a box or restrainer in the liner
area to hold to tools? They're in a box, I assume? Any photos? Thanks
Richard
1985 37 CB; Ohio River, Mile 596;
Richard N. Bush 2950 Breckenridge Lane, Suite Nine
Louisville, Kentucky 40220-1462
502-584-7255
--
The section of sole under my nav table, where I put my feet, was just screwed
down to the interior liner. I pulled it up and cut a hole in the liner,
accessing an area big enough for tool storage so I can use the top drawer for
something else. It's far enough aft and high enough that any bilge w
Tom, the table in my 78 was also attached to the mast track. I've had the
table out for a while. When I locate the parts and pieces I'll send pictures.
Mike
Virginia Lee 1978 C&C 36 CB
Virginia Beach, VA
Sent from my iPad Mini
> On Dec 31, 2015, at 22:29, S Thomas via CnC-List
> wrot
21 matches
Mail list logo