I live on the edge - it was a tabloid website. My phone probably has
herpasyphagonaclaids now.
On Wed, Nov 8, 2017, 1:03 PM Ronald B. Frerker via CnC-List <
cnc-list@cnc-list.com> wrote:
> Was that a legitimate email?
> It had no narrative so I was afraid to open it.
> Ron
> Wild Cheri
> C 30-1
I don’t think so
Marek
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Ronald B.
Frerker via CnC-List
Sent: Wednesday, November 8, 2017 16:02
To: cnc-list@cnc-list.com
Cc: Ronald B. Frerker
Subject: Re: Stus-List Paul Parsons email???
Was that a
Scott,
I might have a new, spare one aboard my boat. Contact me off list and I
will let you know.
Jake
Jake Brodersen
C 35 Mk-III "Midnight Mistress"
Hampton VA
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Scott
Baker via CnC-List
Sent:
Was that a legitimate email?It had no narrative so I was afraid to open
it.RonWild CheriC 30-1STL
___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to support the list - use
Also, ask a B tech if a different transducer will work. You might have
to install a thru hull next haul out. Most log transducers (non-Doppler)
simply send a pulsed signal as a magnet passes a pickup sensor.
Dennis C.
On Wed, Nov 8, 2017 at 1:12 PM, Scott Baker via CnC-List <
Hello Scott,
You might try Chicago Marine Electronics also listed as Hellas Marine. (630)
501-1938. I have B Network and have been satisfied. It's a one man
operation. Owner is Achilles. There is also a B service facility in Florida
(877) 310-5443.
Greg Alimenti
C 29 MkI
From: CnC-List
Did you try either of these guys?
http://www.myleselectronics.com/
http://www.bandg-service.com/
Dennis C.
On Wed, Nov 8, 2017 at 1:12 PM, Scott Baker via CnC-List <
cnc-list@cnc-list.com> wrote:
> Thanks for the tip Dennis, but no joy. L
>
> I’m still seeking the replacement part B number
Do you drag that whole thing under your boat? Seems very large
Mike
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Scott Baker
via CnC-List
Sent: Wednesday, November 08, 2017 3:13 PM
To: cnc-list@cnc-list.com
Cc: Scott Baker
Subject: Stus-List B Impeller
Thanks for the tip
Thanks for the tip Dennis, but no joy. :(
I'm still seeking the replacement part B number 110-10-B21
Which looks like this:
[cid:image001.jpg@01D3589B.A3E22B80]
It seems that they come up for sale on Ebay from time to time for the nice
price of $150
But, I'll pay it at this point. But there
Yes sorry joe is correct. Baudrate for ais is 38.4k. This can be set in open
cpn as I indicated. Jerry
Sent from my iPhone
> On Nov 8, 2017, at 11:20 AM, Della Barba, Joe via CnC-List
> wrote:
>
> AIS is at 38.4 K, not 4800.
> Joe
> Coquina
>
>
> From: CnC-List
AIS is at 38.4 K, not 4800.
Joe
Coquina
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Jerome
Tauber via CnC-List
Sent: Wednesday, November 08, 2017 11:05 AM
To: cnc-list@cnc-list.com
Cc: Jerome Tauber
Subject: Re: Stus-List AIS improvement + general
The unit sends at 38400 baud, so the serial port needs to be configured for
that. If you were using that port for a GPS, it is likely still at 4800. I
haven't used SeaClear in ages, but I think it has a NMEA window to see incoming
data and I know OpenCPN does. You can get this cable to feed the
If you are using a USB port you have to set up a virtual serial port. Make
sure the serial port is set to the proper baud rate for AIS. This can be done
via Open CPN. Go to options- connections. Click add connection serial port and
baudrate 4800, protocol NMEA 0183. If no ports are listed
Joe,
Got the unit and hooked it up to laptop running OpenCPN and SeaClear III.
Went to beach with whip VHF antennae to test. Nuthin'.
That might be because there was nuthin' sending AIS signals or the laptop was
not communicating via the port.
Any tricks you may pass along before I
No opinion on the hoses.simply don't know.
However, a few weeks ago, I also removed my 33 years old aluminum fuel
tank.there was a pin hole in the bottom where the tank sits on the
wooden platform. Took it to a local machine shop for their inspection
and input. They are in the
I am in the process of replacing my Yanmar mixing elbow on our 3HM motor.
Does anyone have any experience with the stainless replacements being
offered by HDI marine out of Vancouver Wa.? The price looks to be a little
less and they look good on the website.
Thanks,
Brad Crawford
Dora
If you know anyone with a 3d printer and basic working knowledge of 3d
design software, such a cover can be 3d printed easily. UV durability for
some plastic types might be an issue, so probably the end result should be
painted in the end. Materials costs would be negligible, but if you would
have
http://murtalhuette.at/nfuwhgi.php?cal51env
__
Regards,___
Thanks everyone for supporting this list with your contributions. Each and
every one is greatly appreciated. If you want to
18 matches
Mail list logo