Hi Francis,
Basically, you are trying to rotate image by 90. Can you check you LCD to see
if it supports these kind of rotated timing parameters? If it does not, you
will have to take care of rotating input image in the application.
Thanks,
Brijesh Jadav
the display of all consoles
Console rotation will only become available if Console Rotation
Support is compiled in your kernel.
Thanks,
Brijesh Jadav
From: francis kumar [franciskumar2...@gmail.com]
Sent: Friday, July 29, 2011 3:13 AM
To: Jadav, Brijesh R
Subject: Re
Hi,
As far as I remember, TVP7002 does not support any other controls, so driver
returns error for contrast/saturation.
Thx,
Brijesh
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com]
Hi,
VPFE supports YUV422 format. What do you mean by generic YUV format?
Thx,
Brijesh
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
shaofeng zhang
Sent: Friday, May 21,
Are you changing scalar coefficients for downscaling?
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
Yuvraj Pasi
Sent: Friday, February 05, 2010
Hi,
Are you saying Dumped decoded streams works correctly on software players? If
it works, I think there is some timing parameters mismatch.
Which mode are you using for the display? Does your TV support the mode you are
trying to display?
Thanks,
Brijesh Jadav
-Original Message-
Hi Sameer,
You can have lineLength mode than width*2 to make it 32 byte aligned.
Thanks,
Brijesh Jadav
-Original Message-
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
Sameer Naik
Sent:
Hi,
Sometimes, display overscans image and crops image. I had seen this in some of
the TVs. It can be disabled in some TVs. Can you try disabling overscaning on
TV and see if it is still there?
Thanks,
Brijesh Jadav
From:
Hi,
It is not possible to do deinterlacing in VDCE as it can only do down scaling.
Thanks,
Brijesh
-Original Message-
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
yang shaobo
Sent: Friday,
-Original Message-
From: Nitin Mahajan [mailto:nitin...@yahoo.com]
Sent: Monday, August 03, 2009 10:08 AM
To: Jadav, Brijesh R; Vladimir Pantelic;
davinci-linux-open-source@linux.davincidsp.com
Cc: davinci-linux-open-source@linux.davincidsp.com
Subject: Re: 8-bit planar support for Resizer
HI!
Does
for Resizer
Jadav, Brijesh R wrote:
Hi,
As I said, driver does support planar YUV422 resize. This is correct
parameters. Error is because of some other wrong parameter.
It will resize RGB planar data as well but I am not sure about quality of the
output since Resizer is for the YUV422
Hi,
As far as I remember, this application does not work the sample image.
Application actually generates color bar and displays it.
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-boun...@linux.davincidsp.com
Hi,
Driver supports planar Resizer but no in the RGB format. Resizer supports
planar YUV422 scaling.
Thanks,
Brijesh Jadav
-Original Message-
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
Hi,
What is the format of your YUV422 file? DM6467 supports only YUV422 Semi-Planar
format.
Thanks,
Brijesh Jadav
From: Vinayagam Mariappan [mailto:vinayagamenm...@gmail.com]
Sent: Friday, July 31, 2009 5:57 PM
To: Jadav, Brijesh R
Cc: Davinci-linux-open-source
[mailto:vinayagamenm...@gmail.com]
Sent: Friday, July 31, 2009 6:08 PM
To: Jadav, Brijesh R
Cc: Davinci-linux-open-source@linux.davincidsp.com
Subject: Re: saDisplay + DM6467 showing black an white image in SD Display
Hi,
YUV422 = [][U][V].
How about YUV420I have my
Hi,
Can you check whether H3A is enabled in the Kernel and CCDC output for H3A is
enabled? As far as I remember, there was some issue with the H3A and previewer.
When H3A is enabled, previewer stops giving interrupts. Can you check whether
previewer interrupts are coming properly? You can
/proc/interupts is impossible, because when it hungs, it hungs totaly. I
have no way to do anything. Only to restart whole system.
Ondrej Pindroch
SoftHard Technology ltd.
Tel: +421(2)65459327
Fax: +421(2)65459329
Mobile:+421(904)906011
-Original Message-
From: Jadav, Brijesh R brijes
Hi,
As DM6467 does not have any graphics pipeline, frame buffer driver is not
supported.
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-bounces+brijesh.j=ti@linux.davincidsp.com
Hi,
I think the problem is no encoder is registered for this node. We have to
register an encoder driver for the node, which we are going to use. If it is
not available it returns error.
Thanks,
Brijesh Jadav
From:
R
Cc: davinci-linux-open-source
Subject: RE: How to improve image latency
Display frame rate is 25fps it is PAL output.
Ondrej Pindroch
SoftHard Technology ltd.
-Original Message-
From: Jadav, Brijesh R brijes...@ti.com
To: Ondrej Pindroch opindr...@softhard.sk, davinci-linux-open-source
Hi,
What is the display frame rate?
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
Ondrej Pindroch
Sent: Thursday, May 21, 2009 5:48 PM
To:
Hi Gopal,
I think user pointer buffer exchange mechanism is supported in both the
drivers, so you can allocate buffers in one driver and use it in the other
driver without doing memcpy.
Thanks,
Brijesh Jadav
From:
Hi,
This is not possible in frame buffer driver but you can do other way, take the
buffer from frame buffer driver and use it in resizer.
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-boun...@linux.davincidsp.com
Hi.
Both of these things are possible but as far as I know driver currently does
not support these features.
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-bounces+brijesh.j=ti@linux.davincidsp.com
...@yahoo.com; davinci-linux-open-source@linux.davincidsp.com;
Jadav, Brijesh R
Subject: Re: DM6467 EVM Video issue
Hi ,
Thanks for the solution. I also have the same problem and have tried
the
solution that you provide. I just stop and start video streaming again
when
the video
Hi,
This is because DMA and VPIF go out of sync and the way to solve this issue is
to reset the VPIF by streaming off and then streaming it on again.
Thanks,
Brijesh Jadav
-Original Message-
From: davinci-linux-open-source-boun...@linux.davincidsp.com
Hi Ryan,
For the device to be created in /dev, you will need a dummy slave device.
vpfe_probe must be called whether slave is available or not. If this is not
getting called, it means there is some vpfe's name mismatch between name with
which driver is registered as a platform device and name
starting place would be.
My V4L2 and kernel driver kung fu is a little weak :).
Thanks again for the advice.
Ryan
From: Jadav, Brijesh R [mailto:brijes...@ti.com]
Sent: Thursday, March 05, 2009 6:05 AM
To: Ryan Talbot; davinci-linux-open-source@linux.davincidsp.com
to resolve
On 2/19/09, Jadav, Brijesh R brijes...@ti.commailto:brijes...@ti.com
wrote:
Hi,
You can check whether resizer is included in the kernel by
printing /proc/devices. There should be one entry for resizer.
If it is available, you just have to create /dev
Hi,
You can use the utility given at the following location to read/write to any
register from application space.
www.sleepie.demon.co.uk/linuxvme/io.chttp://www.sleepie.demon.co.uk/linuxvme/io.c
Thanks,
Brijesh Jadav
From:
Hi,
You can check whether resizer is included in the kernel by printing
/proc/devices. There should be one entry for resizer. If it is available, you
just have to create /dev entry for resizer. If it is not, kernel does not have
resizer driver. Re-build the kernel with the resizer support.
Hi,
Instead of changing resizer driver, I would suggest to get the major number
from proc and create the node.
Thanks,
Brijesh Jadav
-Original Message-
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf
One more thing is you will need to add driver for your TFT.
Thanks,
Brijesh Jadav
From: davinci-linux-open-source-boun...@linux.davincidsp.com
[mailto:davinci-linux-open-source-boun...@linux.davincidsp.com] On Behalf Of
sunder ramani
Sent: Friday, January 16,
Can you check what is the format of that fb window?
From: davinci-linux-open-source-bounces+brijesh.j=ti@linux.davincidsp.com
[mailto:davinci-linux-open-source-bounces+brijesh.j=ti@linux.davincidsp.com]
On Behalf Of Ragas sag
Sent: Friday, January 16,
Hi,
That's correct. Dm6467 does not support frame buffer driver. It supports only
V4L2 drivers. I have not seen X11 running on V4L2. I am not sure but it might
not be possible.
Thanks,
Brijesh Jadav
-Original Message-
From: davinci-linux-open-source-boun...@linux.davincidsp.com
Hi,
FBIOPUT_VSCREENINFO ioctl is handled in the davincifb.c file in the
Kernel/drivers/video/davinci folder. There are two functions for this ioctl,
checkvar for checking the parameters and setpar for setting the parameters.
Thanks,
Brijesh Jadav
From:
Hi,
As far as I remember, earlier dm644x capture code was not supporting user
pointer buffer exchange mechanism. Can you tell me which error you are getting?
Does it allow to do reqbuf?
Thanks,
Brijesh Jadav
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On
Hi,
Where are you hard-coding buffer size? Can you also check whether user pointer
buffer exchange mechanism is supported in the driver?
Thanks,
Brijesh Jadav
From: Mr. V R [mailto:[EMAIL PROTECTED]
Sent: Friday, November 28, 2008 6:18 PM
To: Jadav, Brijesh R
Hi,
You can get more details about Dm6446 resizer driver and the example from the
following link.
http://focus.ti.com/lit/an/spraai7b/spraai7b.pdf
Thanks,
Brijesh Jadav
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of cai xiaodong
Sent: Wednesday,
Hi,
You can get the previewer information from the following link.
http://focus.ti.com/lit/ug/sprue38c/sprue38c.pdf
Thanks,
Brijesh Jadav
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of huahua5
Sent: Monday, November 10, 2008 2:40 PM
To:
Hi,
This error comes when provided line offset is not correct as per the detected
mode. Please go through the VPIF capture user guide to get to know how to
configure line offset.
Thanks,
Brijesh Jadav
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf
Hi,
I think you can use enable_irq/disable_irq to enable/disable a particular
interrupt or local_irq_save and local_irq_restore to prevent all interrupt to
occur. Can you tell me what you mean by other interrupts of the same type?
Thanks,
Brijesh Jadav
From:
Hi,
As far as i know, driver supports RAW mode of capture. Can you check mt9t001.c
file is available in drivers/media/video folder or in
drivers/media/video/davinci folder?
Thanks,
Brijesh Jadav
From: [EMAIL PROTECTED] [EMAIL PROTECTED] On Behalf Of
as the FBDEV layer, to
display frames.
Thanks,
Brijesh Jadav
From: Naveena M. [EMAIL PROTECTED]
Sent: Monday, September 29, 2008 8:43 AM
To: Jadav, Brijesh R; Phil Quiney;
davinci-linux-open-source@linux.davincidsp.com
Subject: RE: OSD support in DM6467
Hi,
Thank you. So
Hi,
There are many tools to view yuv files. One of them is youtools from
sunrayimage. For RAW images, as far as I know, there are no tools available for
viewing.
Thanks,
Brijesh Jadav
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of ashish pareek
Hi,
The first set of steps is correct. Only thing is you need to export one symbol
in the kernel. Please add below line in the file Kernel/arch/arm/mm/proc-syms.c
and recompile the kernel.
EXPORT_SYMBOL(v4wb_clear_user_page)
Thanks,
Brijesh Jadav
From: [EMAIL
Hi,
Display type mean pixel format? It's because only one pixel format is supported
on dm6467 i.e. YC Planar. So there is no need to change it.
If display type is bt656 or bt1120, it will be selected based on the mode
selected.
dm6467 supports four boot time arguments ch0_output, ch0_mode,
Hi,
Can you try getting the mode set on the Output after running the application?
You can get the current mode by following command.
cat /sys/class/davinci_display/ch0/mode
Thanks,
Brijesh Jadav
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf
: 504-8680
PSP Product
Announcementshttps://sps05.itg.ti.com/sites/sdo/psp/_layouts/listfeed.aspx?List=%7b56D44EE9-AE07-45BB-82BF-47B4CCC9AFEA%7d
From: Deepak Kumar GB [mailto:[EMAIL PROTECTED]
Sent: Thursday, July 03, 2008 12:19 PM
To: Jadav, Brijesh R
Cc: davinci
Hi,
Can you make sure camera is connected to the right port and it is on?
Thanks,
Brijesh Jadav
--
Platform Support Productshttp://dbdwss01.india.ti.com/pspproducts/default.aspx
Texas Instruments Inc
Ph:
50 matches
Mail list logo