Hi Group Has anyone found a way to improve the sensitivity on the 160 Meter
Band?? It seems less lively compared to the other bands even after alignment.
Thanks in advance
Bill KB9IV___
Drakelist mailing list
Drakelist@zerobeat.net
My R4C seemed a bit poor in the sensitivity department so I had an idea to
improve it. I aligned the R4C pretty well but it didn't seem very lively.
So with the bottom chassis visible I took my screw driver and loosened/
tightend each screw twice on each side of the 4 rows of trimmer bracket
Hi Group I have written previously about my R4C having signal leakage in the
SSB mode only affecting the PBT control and S-meter levels.
Someone suggested that the 4NB was causing the leakage so I removed the 4NB and
put some wire jumpers as I didn't have a 4NB plug, no change. However I
Hi Group On the R4C speaker output which is 3.2 ohms. Can this audio be
attached to a computer's microphone jack (typically 50K) using a resistor pad
to prevent overload??
73
Bill KB9IV___
Drakelist mailing list
Drakelist@zerobeat.net
I am stil looking to buy a few Stock R4C Xtals. Mine are way off
frequency...they are:
7.0 Mhz (18.1 Mhz)
28.5 Mhz (39.6 Mhz)
These are Stock R4 any Xtals so they aren't scarce.
73
Bill KB9IV___
Drakelist mailing list
Drakelist@zerobeat.net
I have noticed that when using narrow CW Filter's in my R4C that I hear
low-moderate static bursts,like storm static. I have substituted each and all
the 6EJ7's with new tubes.no change. I removed each and all 6EJ7 tubes and
power it on with no change in the static. I remove the 6BA6 RF
A few weeks back I wrote about PBT levels in SSB/AM modes. It would change
S-Meter levels depending on adjustment of the PBT. I ruled out the 4NB board
by removing it..no change.
However when I removed the bottom cover almost 6 S-Units of PB feedthrough were
reduced and performance was
Hi Bob I think you hit it on the head. Also I'm suspect of the NB cable
harness being draped above the 3rd mixer tube area. I only regret not having a
low end Spectrum Analyzer to end this design anomaly and improve this
situation. As suggested I need to disconnect the NB and short some NB
Hi Group I recently obtained a Sherwood upgraded R4C (SN 22xxx), the only
Sherwood upgrade it doesn't have is the 2K Upper Lower SSB filters. It
performs very well but it has one oddity.
When in SSB mode and the PBT is adjusted Upper Lower end of travel it varies
the S-Meter from S6 middle
Hi Group I am looking to replace out of spec xtals in my Drake R4C receiver.
One's listed are 4-9 Khz off frequency. The * xtals are for 160M 10M are more
a priority. Contact me off list @ wmarv...@charter.net
Wanted:
1.5 Mhz 12.6 Mhz*
3.0 Mhz 14.1 Mhz
9.5 Mhz 20.1 Mhz
10.0 Mhz 21.1 Mhz
For the most part I have found the xtals...thanks Doug!
Best 4th to All
Bill KB9IV___
Drakelist mailing list
Drakelist@zerobeat.net
http://mailman.zerobeat.net/mailman/listinfo/drakelist
Hello Group I am near completion reworking my R4B. In the process I used the
manual resistance chart to validate all was OK before
powering the rig just to be safe.
During check out I found a Big Problem on the V3 pin 5, it was shorted to
ground ..140 VDC !! I used the divide and
Hello Group I have been working on my R4B that has Calibrator Buzz and
intermitent low audio Hum. All tubes are now good and the
SSB/Cw receive is very clean. I replaced the Bias Cap 8 uF no go. Any hints
Best 73
Bill KB9IVV___
Drakelist mailing
13 matches
Mail list logo