W1CG continued:
To answer your question, I am using stranded, silver plated, teflon
insulated #16 wire. It is plenty strong. I have a 3/16" Dacron line
between the two poles to take the strain off the wires. This also
decreases the vertical bend and completely eliminates the horizontal
bend o
Hi Folks, I am in need of a small Astron or similar Power supply for my K1
upto 4 amp would be good or an HW9 PS would be welcome too.
Please reply direct, and state price and condition.Thanks, John KF7OM
___
Elecraft mailing list
Post to: Elecraft
I'm giving some thought to building the KPA100 in the separate enclosure. Can
someone give me an idea on how long it would take to build? I realize that
this is very subjective, but I'd like to get a general idea, say relative to
building a basic K2.
Thanks
Tom
WB2QDG
K2 1103
--
I add to day an external frequency counter connector on an unsed hole
in back on my K2. I am now able to use the internal frequency counter
of the K2 for calibrate my antenna dipper built later this week
far better than listening to CW to find the proper frequency value...
When you are
Will reply to the topic of corrosion with chassis screws on this thread.
The reply from John, G4BOU on the subject of lubricating chassis screws to
help prevent corrosion was:
< 'petroleum jelly' despite being a very good insulator has a lubrication
factor of 1
and any pressure (via the
Jess,
The -24 volts on U4 pin 5 is within the range permitted by the RS232
standard and should be OK. The RS232 signalling voltages are stated as:
"Signal State Voltage Assignments - Voltages of -3v to -25v with respect to
signal ground (pin 7) are considered logic '1' (the marking condition),
w
Hi Steve,
Yes, I've checked and there is a home game at
UTKnoxville on Saturday. MidDay and postgame traffic
through KTown will be slow heading in on I-40. This
coupled with bridge and road construction bottlenecks
should be considered when travelling.
I'm heading to Blaine tonight, and there won'
Craig,
Build the KPA100 first (you can use it immediately with a dummy load or a
resonant antenna or any pre-tuned antenna).
If you build the KAT100 first, you will not be able to test it nor align the
wattmeter until you complete the KPA100 anyway, so it will just sit there
waiting. It should o
Check the wiring of the speaker connector coming from the top cover...It plugs
into P5 in the right front corner of the RF board...If the wires in this
connector are reversed, the speaker will be shorted out when the cover is put
in place and the screws are tightened down...
I once had a K2 in
The KAT100 is a quick build and needs the I/O with the KPA100 for testing.
Do the KPA100 first. Once that's done and tested the KAT100 will go quickly.
Craig
NZ0R
K1 #1966
K2/100 #4941
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Craig Miller
Sent: Fri
When lead/tin solder is outlawed, only outlaws will have solder.
Allen KA5N
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net
I presently have a K2 with KAT2 internal tuner. I do not have a KIO2
installed. I've just purchased the 100 watt amp and external tuner. My
question is which order I should build and test these two units: KAT100
first but no way to communicate with it to test it, or KPA100 first with no
way to use
Hi Guys, I have a fully built and tested k2 SN 03890 with 100w and NB
module with xv50 and xv 144 transverters for sale. I am based in Dublin
so I guess this may be of interest to EU hams.
I am looking for 1200 euro for rig and 200 euro each for the transverters
Please email me if genuinely in
13 matches
Mail list logo