Dear group,
If I wanted to make an external ALC cable for use with a linear, do I just
need to solder pin 15 to phono center, and pin 12 to the screen beneath the
phono cable's sheath for common?
73,
James KC2UEE
__
Elecraft mail
Good Evening,
It got a bit late tonight. I was stuck in a book and time simply melts
away. However, twenty meters has been very good this week. Each morning I
have heard DX stations calling with very good signals. Finding a clear
frequency has become problematic some days but that is a go
Conclusion must be, never ever use 5.0W or 50W except
when calibration is needed.
Why cant power calibration be turned off? Then we would
not have this "source for trouble".
/ SM2EKM
Joe Subich, W4TV wrote:
>
>> So, if I'm tuning up through, say, a Z-Match into a doublet
>> and power ou
Bruce: Assuming that you have a Sub Receiver, see page 37 in the Owner's
Manual - Rev D1 under the section "Dedicated Sub Receiver Controls".
Holding "SUB" will link / unlink the VFOs.
73,
Doug, VE3MV
K3/100 #2432
- Original Message -
From: "Bruce McLaughlin"
To:
Sent: Sunday, Febru
Pressing the SUB switch for a little over one second seems to
alleviate this symptom. This is in the manual.
matt
On Sun, 15 Feb 2009 00:15:23 -0500, you wrote:
>Somehow I managed to get my vfos linked in my K-3. Can anyone tell me how
>to get them unlinked so that turning vfo A does not chang
Hold Sub
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Bruce
> McLaughlin
> Sent: Sunday, February 15, 2009 12:15 AM
> To: elecraft@mailman.qth.net
> Subject: [Elecraft] unlinking vfos
>
>
> Somehow I managed
Greetings,
I am just starting the initial test and cals portion of assembly, prior KNB3
enable and KPA3 installation. Power-up went fine with no errors. Before I
start with Synthesizer Cal and move on, is now a good time to update the
firmware to latest release, then do all the cals? I'm gu
Brand new! Never used. $40 includes shipping CONUS. Paypal no fee.
Reply directly to me please.
73,
Sid
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:El
Somehow I managed to get my vfos linked in my K-3. Can anyone tell me how
to get them unlinked so that turning vfo A does not change vfo B? I don't
know how I managed to do that but I must have pressed the wrong button at
the right time. I haven't been able to find anything about it in the
manua
> So, if I'm tuning up through, say, a Z-Match into a doublet
> and power output is set to "around" 5 or 50W and press "Tune"
> in order to tweak the Z-Match, the initial (off-tune) complex
> impedance the K3 may see could very well cause the K3's output
> power to change to 5 or 50W and beca
For Sale, Factory Assembled LP Pan $175. Price includes shipping conus.
Please reply off the list.
73, Jim
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mail
Hello: I have a new K3 and another radio, but one computer. The other
radio is successfully HRD-interfaced with the PC. I am thinking of
hooking the K3 to the same PC via an RS 232 male-to-female cable. Kosher?
Bill Wade, Ai4PF
__
Elec
OK...so we can send RTTY using the paddle in. What about sending RTTY
using the KEY IN (as in, use an outboard contest program to send CW
and have the K3 convert it to RY).
I know that this was supposed to be "on the list" but was this ever implemented?
Tnx
Doug
_
Yes, but it was also phased in at Aptos on Rev A boards at some point so,
while all Rev A and earlier boards need the mod, the more current K3's with
Rev A boards probably have had the mod made at the factory already.
There's a way to check by just opening the K3's top cover shown in the
document
Looks like I'm ordering another K3. I was wondering, when I place my order
for the second K3 can I ask for the 2.7 filter to be matched (as close as
possible) to my second rx that I will be moving from my older one to my new
one? I lucked out and had a very close match on my old one. I emailed sal
Thanks to all. Got my table. Now to start playing with getting psk up and
running.
73
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman
According to the Enhancements and App Notes page at:
http://www.elecraft.com/K3/k3_app_notes.htm
"This modification is needed for all K3s shipped approximately before
01/12/09 containing either a Revision "XB" or Revision "A" KIO3
board."
Bob NW8L
On Sat, Feb 14, 2009 at 5:41 PM, KC2UEE wrote:
So, if I'm tuning up through, say, a Z-Match into a doublet and power output
is set to "around" 5 or 50W and press "Tune" in order to tweak the Z-Match,
the initial (off-tune) complex impedance the K3 may see could very well
cause the K3's output power to change to 5 or 50W and because of that,
Hi Joe,
> Further, single tone power calibration is only accurate for
> the specific frequency within the IF filter on which the
> calibration is performed. If I calibrate power in CW mode
> that calibration point is approximately 300 Hz from one
> "corner" of the 2.8 KHz filter thanks to the way
Hi Ron,
I just ordered my K3 on Thursday. Do you know if this modification has
already been phased in to new kits?
73,
James KC2UEE
Ron D'Eau Claire wrote:
>
> Hello David:
>
> Wayne asked me to reply since I prepared the application note. Only two
> resistors are needed, so if you've done
Hi All,
I've been having issues since last night with an inability to use the Tune
Function on the K3.
I use Tune to get a carrier to tune my amp (an Emtron DX-1). Usually this works
fine, but now the Tune simply turns itself straight off after it is pressed
when I have the amp turned on. The
Are you using the RX EQ as a peaking filter? EQ is bypassed
when BW is less than 150 Hz.
> -Original Message-
> From: elecraft-boun...@mailman.qth.net
> [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of KM5Q
> Sent: Saturday, February 14, 2009 5:30 PM
> To: elecraft@mailman.qth
Hi gang,
The weekly Elecraft SSB net will meet tomorrow (Sunday, 2/15/09) at 1800Z.
We will start at 14.316 MHz, and QSY if needed. The net control is in
western Oregon, but we will need a good east coast or midwest station to
relay a few west coast signals that may be too close to net control.
Spotted perfectly on a CW signal, I narrow the BW from .15 to .10. I
hear a click and the audio suddenly drops to about 1/3. S-meter
reading stays the same.
It didn't do this when the radio was new, but it has been doing it at
least since FW 2.78. I now have 2.82. My narrowest roofing filter
I've been looking at the k3 programmer's reference trying to get a feel for
what can be accomplished via the serial port. However, the switch location
table in the section on the swt and swh commands got severely scrambled in
the conversion to text.
Could someone out there please send me that
Hi Bill:
Howard was using his VFO B as a fixed frequency receiver and he was tuning
VFO A to listen and change his TX frequency. He was not using SPLIT and he
could not have been using diversity. He had to be unlinked. So he always had
the DX station in his right ear.
What you're describing is
> Why on earth not? I think you are confusing the situation
> with what happens when you press TUNE at 50 watts (which I
> personally think is a disaster that has already happened
> on many occasions, but that is another matter.)
To normalize the radio's output power for any valid test you
n
K2MK wrote:
>
> Also you can't use diversity reception while doing this. You have to
> be unlinked.
>
You can use Split in Diversity, but you must use the REV button to tune the
pileup. It's like using Split with one RX but you're receiving in Diversity
using both RXs. I always LOCK the DX
I spent some time measuring K3 power out vs. TUN PWR setting.
I used a 60 MHz scope for power measurement and a dummy load that measures
1.06 SWR with the 10X scope probe connected. I did all measurements on 40M
and I did these tests after conducting the power calibration procedure that
is part of
Joe Subich, W4TV-4 wrote:
>
>
> You CAN NOT make those tests at 50 Watts! The power calibration
> circuitry will be constantly changing the internal gain. If
> the ATU is enabled and/or your dummy load is not flat the changes
> invalidate the measurements.
>
Why on earth not? I think yo
I have uploaded Version 1.0.3 of K3 Filter Tools to my web site*:
http://www.ks7d.com It includes a bug fix and adds some enhancements:
Bug fix:
· Fixed Quick Test procedure in dBV Linear Range so that Reset K3 works
properly at end of process to reset K3 to its state prior to runnin
Even though I might still get advice on the real necessity to get matched
filters for true diversity rx, I have figured out an easy solution.
When I purchase the sub rx in the future, I will get 2 matched 400 cycle
filters. That way I can have true diversity with the 400's, and almost true
divers
You CAN NOT make those tests at 50 Watts! The power calibration
circuitry will be constantly changing the internal gain. If
the ATU is enabled and/or your dummy load is not flat the changes
invalidate the measurements.
Further, single tone power calibration is only accurate for
the specifi
Hi Howard:
It makes you feel like you're doing something wrong, doesn't it. Make sure
nobody else is in the shack.
With my prior radio, an FT1000D, the sub receiver was not quite as good as
the main receiver. (Different filters and no audio peak filter). So it was
logical to receive with the
Hi David,
Thanks for the information. I didn't realize that the XV432 didn't cover
the whole 70cm band. This is good to know, as I intended to use the
transverter to communicate with local 440 machines. I suppose it would be
better for me then to go with the XV144, or just buy a 2m/440 base ins
I have had good luck with the SEC 1223 which I use for both the K2/100 and
the K3. I purchased from Amateur Electronic Supply.
Bruce-W8FU
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Yves Dussault
Sent: Saturday, February
I saw the questions about K3 headsets.
I have the "ON'AIR" Headset offered by US Interface for about $40.
http://www.usinterface.com/naviusa_012.htm
I have no relationship with the company. Their service was good and I can
recommend the product with the caveats mentioned below.
The headsets are st
of course I meant 2.4a... hihi.
--
View this message in context:
http://n2.nabble.com/K2--6638-Online%21-tp2327124p2327160.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home: http://mailman.
Lyle Johnson wrote:
>
>
> I know the next question: Can we have by-mode Tx EQ? and the answer is
> yes, but you must be patient.
>
> Similarly, the Rx EQ applies to the receiver not the mode, so it is also
> used in all modes that use receive audio, which is all of them :-)
>
>
I can't s
Hello everyone-
Thanks to Don Wilhelm and a few others, my K2 is complete and on the air.
After assembly I had a couple issues... one was the voltage on the display
was extremely erratic and we were able to determine that the vsense pin on
the uP was blown, so I had to purchase a new set of fir
> Thanks to Jim (K9YC) and others for the info on your EQ settings. I'm
> curious if you have to set all these back to "flat" for operating data
> modes that are actually using SSB (like PSK & AFSK). Or are they
> bypassed when you change main mode to DATA?
There is *one* Tx EQ in the K3, so
I discovered that my cw power issue was due to a bad power supply for my
Elecraft W1 wattmeter. My cw power measurement now agrees with the K3
setting. I still see a 50% higher power output in Data A mode than the K3
setting -- this is an improvement over the nearly 100% that I was seeing
using pre
Thanks to Jim (K9YC) and others for the info on your EQ settings. I'm curious
if you have to set all these back to "flat" for operating data modes that are
actually using SSB (like PSK & AFSK). Or are they bypassed when you change
main mode to DATA?
73, Barry, K6RM_
I'm sure this is obvious to most but not to me. I am blaming it on separation
anxiety since my K3 only recent returned from Aptos.
I have the KRX3 installed and work split using the Sub Rx. I lock vfo B on the
DX and use vfo to find a tx frequency. When might using the split button be
indicat
Steven.Zabarnick wrote:
>
>
> I installed the new beta last and tested the new output power control. I
> don't see any improvement in PSK31 output power using DATA A mode. I still
> get nearly twice the output power than I have dialed in by the PWR knob.
> In
> the previous firmware, the measur
I now have the spring fever for building...Thinking of putting the
KPA100 together for my K2.
Any suggestion for a suitable (cheap!) power supply?
--
Yves Dussault-VE2ATD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/l
I saw that someone had changed one of the bands on an XG2. Has anyone done
that with the XG1? I have both. Not worth trying to sell the XG1. So thought
it would be nice if it could be changed to 160M or 10M.
Any thoughts on this?
73,
N2TK, Tony
The frequency is plus or minus the QRM. Note the
start time of 1000 hours to try and minimise
European QRM.
73 Dave, G4AON
K3/100, Acom 1000, dipole
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Hel
Ralph Parker wrote:
>> I don't know why VOX has to be turned on explicitly in CW mode.
>> Since nothing happens without it, it may as well be turned on automatically
>> when you select CW.
>
> No, thanks!
> I don't necessarily want to transmit everytime I hit my key.
> And I often prefer a foot sw
I'm running two K3s, each into its own Alpha 86 at 1.5 KW. Same
configuration at home with 87As. I've never encountered what you describe.
Ed - P49X (W0YK)
> -Original Message-
> From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
> boun...@mailman.qth.net] On Behalf Of Ron W3ZV
>
Hi Colin,
I'm using ver 2.80 and split is working fine here, although I still
haven't managed K5D yet. Did you A>B before selecting split?
Doug GM0ELP
Colin Potter wrote:
>
> Hi all, need help!
>
> Using ver 2.78 ser 2014. Find SPLIT is not working CW or SSB! Was working
> previously with o
Hi Dave
I do not have the problem you are experiencing. My K3 works fine in split in
transmit with the sub receiver on.
I hope you find the problem.
73
Barry VK2BJ
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/list
Mike,
I installed the tuning pot you suggested and so far so good. It does
feel better when tuning and has been pretty stable. Hopefully this will
fix the issue. It is quite impressive that you achieved DXCC with the
K1, Congratulations and Thanks.
73
Steve
Michael Byrd wrote:
> Steve,
>
> I h
Lyle Johnson wrote:
>
> In FM mode, hold PITCH. Select the CTCSS tone with VFO A and
> enable/disable with VFO B.
>
Got it! Serves me right for looking for "CTCSS" in the index of the manual.
-
Julian, G4ILO. K2 #392 K3 #222.
http://www.g4ilo.com/ G4ILO's Shack http://www.g4ilo.com/
Hi all, need help!
Using ver 2.78 ser 2014. Find SPLIT is not working CW or SSB! Was working
previously with other versions. Powered up again and reloaded firmware & DSP to
no avail.
SPLT SV YES or no - makes no difference. Checked mode same VFO A and VFO B.
Need this for K5D asap!!
73 Colin
55 matches
Mail list logo