In a recent message, Bob McGraw - K4TAX rmcg...@blomand.net wrote ...
And here's the frequenices.
Channel Nominal Tuning Frequency (carrier)
1 5332kHz 5330.5kHz
2 5348kHz 5346.5kHz
3 5368kHz 5366.5kHz
4 5373kHz 5371.5kHz
5
Just wondering: is EQ-per-mode still on the list?
Since K3 has also found use for AM-sync BC and VHF FM, different settings
per mode would be even more welcome.
Some time ago I had the impression it was quite high on The List :-)
73'
Paul
PD0PSB
--
View this message in context:
Oh yes please
Gary
Vk4FD
--Original Message--
From: pd0psb
Sender: elecraft-boun...@mailman.qth.net
To: Elecraft
Subject: [Elecraft] EQ per mode?
Sent: Apr 9, 2010 6:32 PM
Just wondering: is EQ-per-mode still on the list?
Since K3 has also found use for AM-sync BC and VHF FM,
Chuck,
LP Pan mostly is a spot and click assist to operating, it
really will not be a better or different second signal
channel than the K3's audio. There is, of course, no weak
signal diversity improvement from running LP Pan in one ear
and the K3 in the other.
Stereo diversity reception
Thanks for the replies - and Don, I'll leave it in until I next open the rig
_ I haven't noticed any detriment - but there is no point in having them
both in.
73 John VE3NFK
--
View this message in context:
http://n2.nabble.com/K3-KXV3-RXA-Mod-tp4873179p4876689.html
Sent from the [K3]
Well, for what it's worth, I'm still trying to get over my prejudice that
computers and HF rigs don't mix but that's going with extreme difficulty
recently hi hi. I've been experimenting with grounding schemes, chokes and
so on with exasperating results with my macs and the K3. At this point,
I would like to sell my KDSP2 option w/manual for $150 or trade for a KAF2
plus $100. This can be a cheap way to get DSP in that K2 wonderbox. Please
email direct.
--
View this message in context:
http://n2.nabble.com/KDSP2-F-S-or-trade-tp4876835p4876835.html
Sent from the Elecraft mailing
Thank you for the info Tom. I appreciate it.
chuck
73
--
View this message in context:
http://n2.nabble.com/Second-receiver-options-tp4874082p4876892.html
Sent from the [K3] mailing list archive at Nabble.com.
__
Elecraft mailing list
Hello All,
Has anyone found a source for 15 pin Y cable ??
Thanks Ken K5DNL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
The latest beta firmware has separate EQ for CW. I would like to have it for
all modes as well, not that I use AM, but for FM RX I certainly don't want
the treble roll-off I prefer on SSB and CW.
There is also a new command to set TX EQ programmatically. I suspect that
those who want multiple EQ
Wow! what Mac are you using?
I have my iMac (2008 2.8 GHz C2D ) sitting next to my K3 and it is on all the
time.
The only noises in the radio that I have experienced are:
A slight hum in the Line In - probably caused by them not being on the same
plug and/or not bonded together. Solved
http://www.altex.com/VGA-Male-to-2-VGA-Females-Y-Adapter-70-568-P142649C1070
3.aspx
73,
Dick - KA5KKT
Hello All,
Has anyone found a source for 15 pin Y cable ??
Thanks Ken K5DNL
__
Elecraft mailing list
Home:
Cables Wholesale:
http://www.cablewholesale.com/cgi-bin/search.cgi?text=10H1-27708
Altex:
http://www.altex.com/VGA-Male-to-2-VGA-Females-Y-Adapter-70-568-P142649C10703.
aspx
73,
... Joe, W4TV
-Original Message-
From: elecraft-boun...@mailman.qth.net
Hello All,
WOW thanks for the fast response , I'm
assuming these have all 15 pins hooked up ??
Thanks Ken K5DNL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
As I've said to others privately, it's most likely my indoor antenna. So I'm
likely just complaining with the solution already in hand hi hi. Because I
live in apts., I've always been restricted to indoor ants so this goes back
a long ways even back into my PC days.
That said, my macbook pro
Oh no, still have to bring a PC!
I thought working *without* Windows was the charm of K3.
Was hoping for a full EQ-per-mode solution,would have made everybody happy
at once :-)
73'
Paul
PD0PSB
The latest beta firmware has separate EQ for CW. I would like to have it
for all modes as well, not
I don't have any problems with RFI and my K3/Mac at all and I do have some RF
in my shack.
I do use a microHam DigiKeyer. But I would have thought any opto coupled
connection and audio transformer isolated connections would be fine.
73 de M0XDF, K3 #174
--
A person usually has two reasons for
Got my K3 back after having the 144 module installed and all hardware
updates done. Works wonderful except for one aspect. I have several SDR
platforms to use and in every one, the panadaptor base line is below the
-140 and I can't see the signals. Worked fine before. Any ideas?
Phil
You can set up a few (admittedly not too many) K3 macros containing EQ value
settings using the TE command and have them available from the front panel
of your K3 with a couple of switch presses. See the second CUT LO example
at the bottom of the Command Tester/K3 Macros page in K3 Utility Help
On Fri, Apr 9, 2010 at 2:32 PM, Ken Roberson kwrober...@yahoo.com wrote:
Hello All,
WOW thanks for the fast response , I'm
assuming these have all 15 pins hooked up ??
More importantly, you want to make sure that none of the (usually
unused by VGA) pins are shorted to the shield. The
As a package only, a factory wired K3 version of the LP-PAN and E-MU 0202
audio interface. Both are less than one month old, excess to my need.
Shipped prepaid USPS stateside; $260.
Contact Bill off relector; _w0...@aol.com_ (mailto:w0...@aol.com) , or
515-386-2262
I have been blocked from access to the list for several days - so trying again
73, Ed - KL7UW, WD2XSH/45
==
BP40IQ 500 KHz - 10-GHz www.kl7uw.com
500-KHz/CW, 144-MHz EME, 1296-MHz EME
DUBUS Magazine USA Rep dubus...@hotmail.com
Make sure you have the correct antenna selected. Also check and see if the
RX antenna is selected by mistake. If you don't have an RX antenna, you get
the symptoms described. DAMHIK :)
Adam
K3ARK
-Original Message-
From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
There is no voltage on the jack - so how do you turn it on?
page 17 says: provides up to 0.5 A (switched) for use with accessory
devices.
Index refers you to page 17
I looked thru the MAIN and CONFIG menus and found nothing to turn on 12v OUT.
No voltage by just turning on the radio
I am trying
I am using the 1/10/08 schematics - it shows a fuse (F2 - 0.6A) for the aux
12 Out. It is connected after the DC control FET. If the radio is on the 12V
Out should have voltage.
I'd suggest checking F2 first.
George
AI4VZ
--
There is no voltage
Hello,
Thanks to all for the 15 pin Y cable info.
73 Ken K5DNL
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This
Chuck,
In his response to your KRX3 vs LP-PAN question, Tom, W8JI, mentioned
the advantages of diversity reception by adding the KRX3 to your K3. I use
this feature very often of the lower 3 HF bands and strongly second this
recommendation . Using the KRX3 sub receiver in my K3 with a second
Thank you Hank, and others.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help
Last night I started setting up PSK31 using HRD and DM780.
I am using an older Lenovo T60p computer in a port replicator, running
Windows 7. I made direct connections using 1/8 stereo audio plugs
between the line in-out connectors on the K3. The line out goes to the
microphone input in the
Phil, is this the case for all bands, or just 2m? If it's all bands,
make sure that the little cable that connects the K3 IF buffer to the
rear panel connector is seated properly. Also, make sure all the
applicable modules are enabled in Setup.
Larry N8LP
Date: Fri, 09 Apr 2010 11:25:35
Phil, is this the case for all bands, or just 2m? If it's all bands, make sure
that the little cable that connects the K3 IF buffer to the rear panel
connector is seated properly. Also, make sure all the applicable modules are
enabled in Setup.
Larry N8LP
Date: Fri, 09 Apr 2010 11:25:35
On Fri, Apr 9, 2010 at 4:45 PM, Edward Cole kl...@acsalaska.net wrote:
There is no voltage on the jack - so how do you turn it on?
page 17 says: provides up to 0.5 A (switched) for use with accessory
devices.
Index refers you to page 17
I looked thru the MAIN and CONFIG menus and found
George,
I trust you meant QSO instead of QSL - the cards come after the contact.
:-)
Check the menu for MIC SEL when the K3 is in DATA A mode. If it is set
to anything other than LINE IN, it will not work from the Line In input.
Once you have set the microphone select menu correctly, go into
Thanks for the info. That is exactly what I was looking for. I will go
through this tonight, I am sure that is the answer.
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Don Wilhelm
Sent: Friday, April 09, 2010 1:26 PM
Largely the issue of RFI can be more related to antenna location and the
radio/computer location. The closer the two are the more problems are
likely to arise. The signal strength at a specific location is defined by
the inverse square law. Double the distance and the RF field decreases by a
In my experience, often the primary source of computer RFI is the router
and the cables connected to it. I have to turn off my router and modem
if I want to operate on HF from the same room as the computer. No
problem with the computer itself.
Al N1AL
On Fri, 2010-04-09 at 21:00 -0500, Bob
I took my KX1 outside to see if I could track down a router-ish noise on
20m, and when I couldn't I switched to 30M as I was using a 30M MFJ
short loaded whip. I heard SM4OTI booming in. I put the KX1 on top of
the car for ground and gave Steve a call, but no joy. I came inside and
got an
37 matches
Mail list logo
