I think the answer as to why an owner would want a schematic is given to us by
the slogan, Elecraft - Hands on Ham RadioSimple as that.
Rick K2XT
__
Elecraft mailing list
Home:
Estate radio for sale:
K2 Transceiver (serial number in 58xx range)
Transceiver includes:
KSB2 SSB Module
K160RX 160 Module
KNB2 Noise Blanker
KAF2 Audio Filter
KAT2 20 Watt Tuner
KIO2 Serial Port
Kenwood Microphone
Rework Modules
KPA100 KAT100 (100 Watt Amplifier and 100 Watt Tuner) Built
Hello Scott,
I suggest we should also put in a suggestion Contact supp...@elecraft.com
Shipping of the entire amplifier could be expensive. The merit of elecraft
products are their module design which is very good for overseas user. I
simply ship back the defective module instead of the
Has anybody asked Elecraft support for a schematic?
Cannot imagine they would say no.
Just sayin...
73
Gary
Vk1ZZ
K3, KPA500-FT, KAT500-FT
On 29/03/2015 11:03 AM, Johnny Siu vr2...@yahoo.com.hk wrote:
Hello Scott,
I suggest we should also put in a suggestion Contact
A simple enough request - yet such nasty and unhelpful responses. Are
they really necessary?
And, yes.. schematics should be available for ALL ham equipment. In
fact, they should accompany all ham equipment when purchased.
Bill W2BLC K-Line
Good advice, Phil
73, Phil W7OX
On 3/27/15 9:07 AM, Phil Hystad wrote:
Jerry,
You might try my tested and very successful method of working on Elecraft gear.
1. Open up the cabinet (top and bottom).
2. Observe the components inside, looking at each one, contemplating issues,
and
I was wondering if anyone could email me or direct me to where I could download
the PDF document on how to change out P30 and P35 on my K3 with the upgraded
gold pin headers. MikeVE3WDM
__
Bill,
You are correct. The schematics should simply be available for download in the
elecraft official website.
73
Johnny VR2XMC
寄件人︰ Bill w2...@nycap.rr.com
收件人︰ elecraft@mailman.qth.net
傳送日期︰ 2015年03月28日 (週六) 3:45 AM
主題︰ Re: [Elecraft] Looking for a KPA500 Schematic
A simple
Seems like you may have a bad connection between the RF board and the tuner, or
between the tuner and the BNC connector. I'd investigate that first. If no
luck, try removing the tuner altogether and see what happens into a dummy load.
If you contact Ekecraft support, they can help you isolate
I had a similar problem with my KX3. My problem included no
receive. The upshot was that the KX3 had been dropped and the
antenna BNC connector had been pushed in just a little. The
clearances are quite tight there, and the antenna BNC was
shorted. I bent the case back into shape, removed the
I've been following this discussion with interest. I've used the NCC-1 with
my K3 for several years now. I use one of the DX Engineering 102 active
antennas for noise pickup to cancel noise on my Tx vertical antennas.
My best success with noise cancellation has been on the higher bands
On Fri, 27 Mar 2015 12:53:33 -0500
Grant Youngman n...@tx.rr.com wrote:
This is very similar to the car quits on the road diagnostic technique. The
first step is to pull off the road. Step 2 is to open the hood and stare at
the engine. Look everywhere. Look at it very carefully. Is it still
Our clocks change this weekend which prompted a GMT time check on K2
#5565. From page 33 of the manual, holding STORE+RCL displays the 5 dashes
and tells me that I am not in a DSP menu. For me to proceed I need to know
what constitutes a DSP Menu? Secondary Menu, RTC is ON. Any guidance much
Anything under 2:1 will allow the TX GAIN calibration to work, but I'd shot for
1.5:1.
Wayne
N6KR
On Mar 27, 2015, at 5:27 PM, Phil Hystad phys...@mac.com wrote:
I have two dummy loads that might be useful for the 50-watt TX-gain
calibration but neither of them are dead on with a 1:1 SWR
I don't believe that there is a misunderstanding at all. The FCC rules state,
among other things:
§ 97.1 Basis and purpose.
The rules and regulations in this part are designed to provide an amateur radio
service having a fundamental purpose as expressed in
the following principles:
(a)
I would like for the KX3 ANT button press/hold to select a second set of ATU
tuned elements for another antenna which I select with an external antenna
switch. I have two antennas which need different tuner settings for each HF
band. Whenever I change from one to the other I have to retune the
Selling my Elecraft W2 wattmeter, it looks and works like new, from a
non-smoking environment. Comes with the manual, RS232 interface cable, power
cord with power pole connector and cable to connect unit to the sensor. The
sensor is the 1.8 - 54 MHz 2 KW model. I bought it from the original
I have two dummy loads that might be useful for the 50-watt TX-gain calibration
but neither of them are dead on with a 1:1 SWR and 50 ohms resistive load.
Actually, my smaller 150 watt dummy load is closest with a range of 42 ohms on
the load to about 55 ohms on the high end as I step through
Ping. Is anybody out there?
--
73/72 de Ingo, DK3RED - Don't forget: the fun is the power!
www.qrp4fun.de - dk3...@qrp4fun.de
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Phil and all,
There are two types of dummy loads - one is simply to provide a load to
your transceiver or amplifier for a quick sanity check that the
transceiver or amp is providing output and is capable of transmitting a
signal.
The other type of dummy load is one used for calibration
599 001...contest
Gary
Vk1ZZ
K3, KPA500-FT, KAT500-FT
On 29/03/2015 9:32 AM, Ian Kahn km4ik@gmail.com wrote:
Your email is 59 into South Carolina. :-)
On Mar 28, 2015 7:23 PM, Ingo Meyer, DK3RED ma...@qrp4fun.de wrote:
Ping. Is anybody out there?
--
73/72 de Ingo, DK3RED - Don't
Your email is 59 into South Carolina. :-)
On Mar 28, 2015 7:23 PM, Ingo Meyer, DK3RED ma...@qrp4fun.de wrote:
Ping. Is anybody out there?
--
73/72 de Ingo, DK3RED - Don't forget: the fun is the power!
www.qrp4fun.de - dk3...@qrp4fun.de
Mark,
You must first tap DISPLAY to get into the DSP menu.
Without being in a DSP menu, a hold of STORE+RCL normally puts you into
a Direct Frequency Entry state which will display the dashes that you see.
73,
Don W3FPR
On 3/28/2015 10:55 AM, Mark Raybould wrote:
Our clocks change this
Phil,
Your 20-watt dummy load will work with the automated procedure, and it is
the best one because if the SWR is over some threshold you'll get a SWR
too high, calibration failed message.
The 20-watt load is very unlikely to overheat; my 10-watt load did not
overheat, because the 50-watt
Has anybody asked Elecraft support for a schematic?
I was about to ask the same thing. This thread is just plain silly. When I got
my KPA, I simply called them up and asked for one. They obliged. So simple. I
do happen to agree that it should have been provided in the package though.
Gary
Phil, why don't you hold it on 17 meters this weekend? A number of the
SOTA crowd that frequent the SSB freq's from summits went to 17 and 12
meters today. SFI is pretty high relative to what it has been, 17 might
be a good analog for 20.
73,
Fred K6DGW
- Northern California Contest Club
-
I run my K3 from a Pyramid ps21kx power supply, a linear supply which has
done a great job for a couple of years. But it has a fan, and when there is
nothing going on in the shack, the fan is audible. So I got a temp control
gadget on eBay for 15 bucks shipped from the U.S. I opened up the power
Unbelievable.
On 3/27/2015 10:40 AM, Scott Manthe wrote:
Why would you want a schematic? If it's new, Elecraft will fix it free. I'm
all for being able to troubleshoot my gear, but if I buy something new and it
fails within the warranty period, I'm not going to waste my time trying to fix
it,
Apparently there is some misunderstanding regarding my comment (Or
people are responding without reading the entire message closely...). I
was NOT responding to the original poster. I was responding to the
second commenter, who said that he needed a schematic because his NEW
KPA500 had failed.
The weekly Elecraft SSB net meets Sunday at 1800Z on 14.3035 MHz. There is a
big contest underway, which may make conditions rough; but what the heck, let’s
give it a try. I will be net control from western Oregon. See you there.
73,
Phil, NS7P
There is a set of 17 pages pdf that can be downloaded from www.mods.dk
No idea how old it is ...
Harlan
NC3C
Sent from my Verizon Wireless 4G LTE smartphone
div Original message /divdivFrom: Gary Gregory
vk1zzg...@gmail.com /divdivDate:03/28/2015 10:06 PM (GMT-05:00)
Lots of people like to have an understanding of what is under the hood, whether
they can fix it or not. ;-)
BTW it isn't that hard to find a copy on the Internet, I am rather surprised
Elecraft don't supply them with the amplifiers, it never crossed my mind that
they wouldn't.
73
David
As we all gear up for the CQ WPX SSB contest this weekend, I would like to
remind everyone to jump back in in two weeks, April 11 and 12, for the
Georgia QSO Party. This is one of the largest, best state QSO parties in
the country. We hope to have all 159 counties on the air, for all the
33 matches
Mail list logo