I'm not at home to check, but isn't there a CONFIG: setting required for
that? 73, Guy K2AV
On Saturday, June 6, 2015, Jim Sheldon w...@cox.net wrote:
I have exactly the same problem here. My K3 doesn't recognize the KXV3B.
I triple checked the install. Funny, but the RX-IN works and my
Perhaps it was 3-phase hum? The really big amps run on 400V 3-phase circuits
(no, Elecraft won't be making these)!
Vic 4X6GP/K2VCO
On Jun 6, 2015, at 12:54 AM, Oliver Dröse dro...@necg.de wrote:
Hi Gernot,
as I am hearing lots of similar signals from a few of the very very big guns
Elecrafters,
If you have totally unknown toroids, this useful program should help:
Download , copy to your favourite folder and run (linux users run it
under wine).
miniRingkernRechner.exe (miniToroidCalculator)from here:
http://www.df7sx.de/?page_id=212
Read HELP
Set your language , then
On Sat,6/6/2015 3:25 AM, Martin wrote:
If you have totally unknown toroids, this useful program should help:
Not necessarily. This program and the measurements upon which it depends
tell us about the INDUCTANCE of a core, but NOT the RESISTANCE. When we
use ferrites for suppression (common
Hi Carl,
Four bars solid and the 5th bar flickering is the correct way to do it.
73,
Mike K2MK
Carl Jón Denbow wrote
I have ALC set so that I get four bars, with the fourth bar solid most
of the time but flickering every now and then. Is that the right
amount, or should it be four solid
The best way to determine the core performance is to do what the
manufacturer does.
Use an analyzer to look a Ui and U''i over frequency to get an idea of the
material type.
The 2nd best way is to wind a few turns to see what the Rs is over the
frequency of interest.
The best is to build an
Hi Olli,
yep, this might be the case ... but I did not check during the contest
using other receivers than those mentioned - I was quite busy :-)
73, Gernot DF5RF
__
Elecraft mailing list
Home:
To those who are having KXV3B Problems and getting the ERR XV3 message,
as Joe W4TV said, you must first have beta firmware version 5.26
installed. Then go to the KXV3 item in the menu, make sure it's set to
NOR and tap 9 on the keypad. This will switch it from KXV3 to KXV3B.
To enable the
Yes, thanks for the information.
I don’t see that in the KXV3B installation instructions, or at their web site
which mentions the changes to the firmware revisions here:
http://www.elecraft.com/K3/k3_software.htm.
73 de Sebastian, W4AS
On Jun 6, 2015, at 5:41 PM, Jim Sheldon w...@cox.net
You need to set PREAMP2 to on by holding down MENU/CONFIG. Then press the PRE
button and it will rotate from OFF to PRE 1, then to PRE 2.
This needs to be done 3 times, if you desire, for 6, 10 and 12 meters.
73 de Sebastian, W4AS
On Jun 6, 2015, at 6:35 PM, Dick Hanson d...@dkhanson.com
Go to Config, KXV3, tap 9
Exit the menu.
73,
Bob, N6CM
On Sat, Jun 6, 2015 at 2:26 PM, Jim Sheldon w...@cox.net wrote:
Yes there is, but it doesn't work because the K3 (not K3S) firmware is not
recognizing the KXV3B module or at least not recognizing some parts of it.
Some of the hardware
You are now the third person to mention this. I have emailed support so
hopefully we can get an answer on Monday.
73 de Sebastian, W4AS
On Jun 6, 2015, at 5:25 PM, Dick Hanson d...@dkhanson.com wrote:
Hello.
Just back on list, so may have missed the answer to this.
Installed the
BINGO! I must have missed that somewhere in the release notes or
something. Works like a champ now! THANK YOU!
Jim - W0EB
-- Original Message --
From: Robert Friess rfri...@usa.net
To: Jim Sheldon w...@cox.net
Cc: Elecraft elecraft@mailman.qth.net
Sent: 6/6/2015 4:37:18 PM
Dick,
Update your firmware to 5.26 (beta). It is necessary to recognize
the new options.
73,
... Joe, W4TV
On 2015-06-06 5:25 PM, Dick Hanson wrote:
Hello.
Just back on list, so may have missed the answer to this.
Installed the above today in SN6141, with 5.14 firmware.
At the end
Install the 5.26 Beta ..
Installed the above today in SN6141, with 5.14 firmware.
At the end of the installation booklet, it says to refer to the Owner's
Manual for enable instructions.
When I turn it on now, it gives and err xv3 message.
Yes, it must be done separately for each band. That is what is meant by
per band setting.
73,
Don W3FPR
On 6/6/2015 8:14 PM, Sebastian wrote:
You need to set PREAMP2 to on by holding down MENU/CONFIG. Then press the PRE
button and it will rotate from OFF to PRE 1, then to PRE 2.
This
Don,
thanks for the hints. The K2 is almost original with some simple mods
that had been published during the early days.
I pulled out my XG3 and tried to reproduce the problem. But I could not
hear a clean 2nd or 3rd signal, but a lot of hard noise nearby.
I guess the XG3 is just not clean
I'm running 5.26 here. I don't have the KXV3B in this K3.
In CONFIG:KXV3, tapping the '9' key toggles between KXV3 and KXV3B. I
haven't consulted the current manual, so don't know if this hidden
function is suposed to work. It will get you out of the woods though.
73!
matt
W6NIA
On Sat, 06
First of all, thanks to all for responding!
The good news, fwiw, is that I was able to toggle to the B configuration by
following Bob's suggestion of going to the KXV3 menu and then pressing 9.
It switched to the new configuration and no more err.
When I press PRE, it now briefly
Hello.
Just back on list, so may have missed the answer to this.
Installed the above today in SN6141, with 5.14 firmware.
At the end of the installation booklet, it says to refer to the Owner's
Manual for enable instructions.
When I turn it on now, it gives and err xv3 message.
Must be
Yes there is, but it doesn't work because the K3 (not K3S) firmware is
not recognizing the KXV3B module or at least not recognizing some parts
of it. Some of the hardware apparently works for some people and not
for others. I'm thinking this may depend on the age of the K3? Mine is
#5027
Ah, yes
After setting KXV3B mode, don't forget to exit the CONFIG menu and
power-cycle the K3. It should be fine after that step.
73,
matt
W6NIA
On Sat, 06 Jun 2015 14:58:08 -0700, you wrote:
I'm running 5.26 here. I don't have the KXV3B in this K3.
In CONFIG:KXV3, tapping the '9' key
Have an Elecraft K3 here.When I try to get Audio from the Line-Out for CW, to
feed into a computer, I get no Audio Out, tried Mono and Stereo Outputson my K3.
Do I need to turn something on in the K3 Menu ??
If I plug into front Headphone Jack on K3, it works.
I need a independent Audio Line-Out
I received today the new KXV3B module, and installed it in my K3 serial number
05864, using K3 Utility Revision 1.15.5.1.
I also updated my K3 firmware, to revision 05.26. I completed the Milliwatt TX
Gain Calibration (since I also have an XV222). For good measure, I also
completed both the
I have exactly the same problem here. My K3 doesn't recognize the KXV3B. I
triple checked the install. Funny, but the RX-IN works and my original VLF mod
works fine and it depends on the XV3's RX-IN jack so contrary to my thinking I
have a defective module, I suspect a problem in FW beta
25 matches
Mail list logo