Howdy..
After rushing to be there when Best Buy opened this am, I bought a new
serial to USB cable.
New cable worked fine, even tho an el cheapo by Elecraft standards. ($19.95
by Insignia)
With 5.26 installed and xmit gain recalibrated, all is well!
This radio is going to PJ5A in a
Just now updating an older K3 with 5.14 using an old winXP machine. The 50W
cal went as expected, the 5w cal gives me an error message: ERR TXG.
starting on 160. During calibration it only reaches 3.3W at 1.1:1 SWR. I can
go an adjust to 5w and it reads 1.0:1 when using a manual key. Tried the
Don't get to phone very often but most of the museum ships seem to be on
SSB today. An awful lot of signals seem to have most of their energy in
close to the carrier and sound constricted [a technical term]. There
are occasional ones that look pretty even and they sound great. I sure
wish
Hi Fred,
I have one on order based on my understanding that it does. If I'm
incorrect I'm sure I'll be corrected.
73 !
Ken - K0PP
On Jun 7, 2015 1:33 PM, Fred Jensen k6...@foothill.net wrote:
Don't get to phone very often but most of the museum ships seem to be on
SSB today. An awful lot
The TX Monitor is a time domain display - not a frequency domain
display. If you want to see the frequency domain display of your
own signal, temporarily disconnect the RS-232 cable between the
two (or connect another SDR to a directional coupler in the antenna
line).
73,
... Joe, W4TV
Julius == Julius Fazekas n2wn via Elecraft elecraft@mailman.qth.net
writes:
Julius I can set the rig and run CW fine @ 5w. calibration doesn't
Julius work. Haven't
Julius tried going back to the old firmware, but see not reason the new FW
Julius shouldn't work. Any suggestions?
The new P3TXMON does not include transmit spectrum monitoring.
Although I’ve never tried it, if you unplug the P3 from the K3, you can/might
observe your transmit spectrum. But this isn’t a feature. Alan sent an email
about this some time ago .. don’t have it, but you can probably find it
Hi,
just shortly testet FW 5.26 on my old K3/100 #727 and having problem
with TUN PWR - when set to 10W there is no power (or 1 - 2W) after TUN
activated (holding button) and then no SWR indication, COMP/ALC disp
blinking. Tried 14W and also the same. (to avoid differencies in the
10W/100W PA
PR6 preamp, in like new condition, with original box and manual. $95, which
includes free USPS Priority shipping CONUS. I will take PayPal or personal
check.
Mike, W4UM
__
Elecraft mailing list
Home:
I just purchased a PX3 and want to mount it above my KX3 I was thinking of
using one of those holders for mounting your phone/GPS in your car ( the
gooseneck variety) has any one tried this? is the thickness of the PX3 a
problem? Thank you.
R Thorpe K6CG
It appears that the gain of the Pre-2 has not been factored into the
S-meter ABS setting unlike that of the Pre-1. I can understand this
being the case with the outboard amps, PR-6 and family. However, given
that this function ins now internal maybe it could be taken into account.
Regards,
Good Morning,
Solar flux has increased providing more ions to support
communications. Hopefully the summer storms will cooperate and provide
semi-quiet conditions. The Pacific Northwest toggle switch has been
flipped to sunny and dry. After weeks with 50 degrees temperatures 80
seems
What level is LIN OUT set to in the CONFIG menu?
73,
Ed W0YK
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted
A very similar experience here as well.
One thing I dislike, is the flashing PRE when preamp 2 is on. It is annoying
to see the constant flashing, to me that generally means there is something
wrong. But it looks like that part of the K3’s display doesn’t have the
ability to display
I was running my K3 remotely and accidentally turned off power before doing a
normal power down. Now K3 will not function. I had once before done this
and remotely reinstalled firmware using the K3 Utility program. That fixed
the problem.
However this time I am having problem with loading
Tap '9' when the KXV menu item is displayed.
The same thing happened to me.
Works great now.
K3 # 6108, fw v5.26
Steve KZ1X/4
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I was running my K3 remotely and accidentally turned off power before doing a
normal power down. K3 would not function properly. I had once before done
this and remotely reinstalled firmware using the K3 Utility program. That
fixed the problem.
However this time I am having problem with
Right now 6 meters is marginally open between KS and the Southeast US.
(NC down to FL). First chance I've had to check out the Preamp 2
function on the new KX3VB. Boy what a difference it makes. Had it set
to Preamp 1 and just barely hearing signals so went to Preamp 2 and
really good copy
My Line-Out level on my K3 was too low, was Set to level of 010
had to increase higher to make things work to level 022
Thanks.
73 Mike
On Sun, 6/7/15, Ed Muns e...@w0yk.com wrote:
Subject: Re: [Elecraft] K3 Line-Out help needed
To: Michael Aust
Anyone else out there using rigctld as a means of interfacing fldigi to
the K3? I'd appreciate to see how you configure Retries, Retry
interval, Write delay and Post write delay.
I'm trying to solve some erratic behaviour that I was not seeing
with rpc.rigd.
Thanks
Pf
--
Pierfrancesco Caci,
Other than when it was posted on the reflector yesterday, I'd like to
know where this information originally came from. It was not in the
installation instructions and so far, I can't find it anywhere on the
Elecraft website and of course it is not in the K3 manuals to include
the latest
Hi Mike,
Check the CONFIG:LIN OUT value. It should be about 10 or so. When you are in
that menu tap the 1 key to make sure it isn’t =Phones.
Good luck.
73,
Fred KE7X
Author of:
The Elecraft K3: Design, Configuration and Operation 2nd ed
The Elecraft KX3 – Going for the summit
“The Elecraft
I have the same problem and find it very distracting. I also have found that
there are additional false artifacts above and below the vfo frequency that
move in sync with any change in vfo frequency.
John K7JLT
David Patino d...@onitap.com wrote:
Howdy All,
So on my PX3 I'm seeing the
Mike,
We'll take preamp 2's gain into account for SMTR ABS in an upcoming firmware
release. We also need to account for the 5/10/15 dB attenuation steps available
in the K3S.
By the way, the MDS on 12/10/6 meters with preamp 2 engaged is a blistering 145
dBm, typical! Have fun--
Wayne
N6KR
Hi Jim,
We intended to post the revised KXV3B installation instructions before shipping
it, but they beat us to it. Sorry about that.
The KXV3B is very well covered in all respects in the K3S owner's manual,
including enable and preamp 2 setup. The K3S manual will be posted soon.
73,
Wayne
Richard -
I have nothing to do with GEM Products, and don't even own a KX3... but at
Dayton, I saw the mounts that Scott has designed for the KX3 PX3. There
is NO doubt in my mind that if I had those sweet little Elecraft products,
and wanted to mount them, the GEM Products devices are what I
Richard, look at my mounting solution at GEMS Home Page I have both KX3 mounts
and PX3 mounts coming out in the next few weeks.
Scott AK6Q
| |
| | | | | | | |
| GEMS Home PageHOME click on an image to enlarge Installation Videos: LA8FTA
KK4NQQ Links: Eham Reviews Elecraft KXLine
Howdy All,
So on my PX3 I'm seeing the issue listed in the manual as Dip in Spectral
Response Close to VFO Frequency. Described as:
I/Q demodulation at baseband (used by the PX3 and many SDR applications) may
introduce small, very narrow-band amplitude variations in the response close to
For Sale K3 serial 3746 (Not K3S) Factory Assembled
K3/100
KAT3
KRX3
KXF3A
2- KF3A 2.8k 8pole filter
KFL3A 1.8k 8pole filter
KFL3A 400 8pole filter
KFL3A 6k 8pole filter
KFL3B 13k FM filter
$3650 includes shipping and insurance
P3 serial 1020 Factory assembled
$635
All perfect condition, non
Thanks to all who replied. I now know that the new feature is time
domain only which doesn't help me. I tried unplugging the RS-232 cable,
and apparently the phase of the moon is not quite right because I really
don't see much. I tried running up the gain [SCALE] to no avail,
brought the
Got it to work, my Line-Out needed to increase to 022 instead of 010 to make it
workThanks Mike
On Saturday, June 6, 2015 11:12 PM, wb6r...@mac.com wb6r...@mac.com
wrote:
Check the setting of LIN OUT in the config menu. Try NOR 010.
GL - Steve WB6RSE
On Jun 6, 2015, at 10:33 PM,
The June sprint is this coming Tuesday evening local time (June 9th,
EDT - 8:30-10:30PM, CDT - 7:30-9:30PM, MDT - 6:30-8:30PM, PDT - 5:30-7:30PM),
which translates as Wednesday, June 10th, 0030 to 0230Z in all cases.
For all the official information, please go to:
The June sprint is this coming Tuesday (NOT Wednesday!) evening local time
(June 9th,
EDT - 8:30-10:30PM, CDT - 7:30-9:30PM, MDT - 6:30-8:30PM, PDT - 5:30-7:30PM),
which translates as Wednesday, June 10th, 0030 to 0230Z in all cases.
For all the official information, please go to:
33 matches
Mail list logo