Ignacy,
I know nothing about the display capabilities of SDR-IQ, so the only
thing I can say is that the actual input frequency of SDR-IQ must be the
same as the IF frequency of the K3 - 8215kHz.
73,
Don W3FPR
On 12/22/2016 3:52 PM, Ignacy wrote:
I am trying to set up CW Skimmer with SDR-IQ
Mike,
The DSP-X board is no longer obtainable, so the kit had to be discontinued.
73,
Don W3FPR
On 12/22/2016 6:38 PM, Mike Weir wrote:
I have built 2 Elecraft K2's and very much miss the kit building thrill. I was
considering purchasing another K2 to build and maybe sell, while I was on the
I had heard that it only affected the speaker. But a friend that has both a K3
and a K3S says the audio is better on the S, and he is a former sound man.
What's known about this?
Vic 4X6GP
> On 23 Dec 2016, at 05:41, Guy Olinger K2AV wrote:
>
> I wasn't referring to the USB sound, etc, found
I didn't exactly do this, but I did investigate the effects of distortion on CW
signals. I disconnected my P3 from the K3 and set the IF to 7 MHz. so it would
act like a standalone spectrum analyzer.
I was interested in whether a class-C amplifier I had built would sharpen the
keying enough to
Actually, anyone considering remote operation Remoterig, QSK is totally
out, not ever going to work.
73,
Fred K6DGW
Sparks NV
Washoe County DM09dn
On 12/22/2016 7:34 PM, Bob Nielsen wrote:
I doubt that you would be satisfied with the delays (QSK is definitely
out!)
73, Bob N7XY
_
I wasn't referring to the USB sound, etc, found in the KIO3BUPKT.
The K3S sound board has higher speaker power power and other
refinements which enhance what you hear in the speaker and headphones.
That is not listed on the page.
73, Guy.
On Thu, Dec 22, 2016 at 10:30 PM, Gary Hembree wrote:
>
I doubt that you would be satisfied with the delays (QSK is definitely out!)
73, Bob N7XY
On 12/22/16 1:37 PM, Bill OMara via Elecraft wrote:
Does anyone have any good new story's in running a k3 remoterig set-up over
a satellite internet system? Hughes Net, Exede or others
I'm intereste
The Clarke Belt is too far away, and the speed of light is
inconveniently slow.
On 12/22/2016 1:37 PM, Bill OMara via Elecraft wrote:
Does anyone have any good new story's in running a k3 remoterig set-up over
a satellite internet system? Hughes Net, Exede or others
_
Try this:
http://www.elecraft.com/elecraft_prod_list.htm#kio3bupkt
73
Gary, N7IR
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Whatever happened to distributing the K3S sound board and its various
improvements for the K3. That's been rumored forever it seems. We have the
various other improvements, synthesizers, new preamp, etc. But not the new
sound board.
Is that project still alive, will it actually happen? If so, a ti
Hi,
I’m using my USB keyboard with the P3+SVGAboard. The keyboard works great until
I power off the P3 then back on. I always have a message on the external VGA
display « USB DEVICE REMOVED » and the keyboard doest not work until I unplug
the keyboard and plug it back again.
When I turn on the
I don't use skimmer so can't begin to comment on that. But I do use an SDR-IQ
with SpectraVue on my K3 and/or K3S i-f output(s). The SDR-IQ follows the K3s
perfectly and conversely, you can point-and-click the screen in SpectraVue and
tune the K3. You can also tune the K3 with the mouse wheel
It was mentioned here. IIRC Lyle (the engineer) said that certain parts had
become "unobtainum".
73 Ron AC7AC
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Mike
Weir
Sent: Thursday, December 22, 2016 3:39 PM
To: elecraft@mailman.qth.net
Subject:
Thanks Mitch
I think we can close this thread as I cant find any light at
the end of the rainbow.
73 Bill W4RM
From: Mitch Wolfson, DJØQN / K7DX [mailto:dj...@gmx.net]
Sent: Thursday, December 22, 2016 6:26 PM
To: Bill OMara ; elecraft@mailman.qth.net
Subject: Re: [Elecraft] K3 remote o
I have built 2 Elecraft K2's and very much miss the kit building thrill. I was
considering purchasing another K2 to build and maybe sell, while I was on the
order page I noticed KDSP2 has been discontinued?? Now maybe I was not paying
close attention to the reflector but I can't remember a post
Bill,
There are *no *good news stories on using RemoteRig over satellite. A
couple of people have been on the RemoteRig Forum where things like this
are discussed at http://www.remoterig.com/forum/index.php and had tried
in vain to get it to work.
As Joe wrote, the latency is too high to mak
Jim and others,
I agree with everything that everyone has said. That's why I was asking
about a good news story? Has anyone tried it?
Any real first hand reports?
The specs don't always tell the truth, but most of the time they do!
73 Bill W4RM
-Original Message-
From: Elecraft [
On Thu,12/22/2016 1:37 PM, Bill OMara via Elecraft wrote:
Does anyone have any good new story's in running a k3 remoterig set-up over
a satellite internet system? Hughes Net, Exede or others
There are at least two issues. The most obvious is latency -- how much
"turn around" time are you able
The latency (delay) through the satellite will probably be a killer.
IIRC, ping times through a satellite link are > 500 ms (120 ms up,
120 ms down *times two* plus any time in the network on each end).
The question becomes can you handle ~1/2 second delay in control
response and deal with audio
I can come close. I currently operate W7RN remotely using our AT&T
Uverse Internet. It's 45 Mbps from the street to the router, and the
computer and Remoterig box run in the 18-20 Mbps down and half that up.
Ping time to the station is in the 40-45 ms range. It works fine [well
... nearly a
Check with Jim Brown K9YC.
Sent from my iPhone
...nr4c. bill
> On Dec 22, 2016, at 4:10 PM, K9MA wrote:
>
>> On 12/22/2016 11:40, Jim Brown wrote:
>> IMD also affects CW. What we call CW is not "continuous wave," it is a
>> continuous wave that is 100% modulated by a rectangular wave. That
Does anyone have any good new story's in running a k3 remoterig set-up over
a satellite internet system? Hughes Net, Exede or others
I'm interested to if this a possible solution to a AT&T DSL internet line
(better or worse?)
Thanks for any input.
73 Bill W4RM
On 12/22/2016 11:40, Jim Brown wrote:
IMD also affects CW. What we call CW is not "continuous wave," it is a
continuous wave that is 100% modulated by a rectangular wave. That
rectangular wave is rich in harmonics, and excites IMD. We hear it as
clicks.
It would be interesting to see how much
I am trying to set up CW Skimmer with SDR-IQ and K3 so that SDR-IQ is
connected to IF OUT and follows K3's frequency. Is this doable?
If not, it there any way of configuring SDR-IQ to follow band changes with
K3?
Ignacy, NO9E
--
View this message in context:
http://elecraft.365791.n2.nabble.c
I like using assigning rig to DXLabs Commander. Seems to work very smoothly
so far. That way there are no port conflicts and I don't need to kill my
logging program (DXLabs Suite) to run WSJT-x.
jim ab3cv
On Thu, Dec 22, 2016 at 2:58 PM, Fred Jensen wrote:
> My first guess is that either DTR or
My first guess is that either DTR or RTS is being asserted by WSJT and
you have it configured in your K3 for PTT. CONFIG --> PTT-KEY -->
OFF-OFF will do it if that's the case. Happened to me.
73,
Fred K6DGW
Sparks NV
Washoe County DM09dn
On 12/21/2016 4:39 PM, Howard Sherer wrote:
I have
Elecraft KPA500 Amp - Bought new as a kit 8/01/2012 s/n 0971- assembled
by myself. Includes KPAK3AUX-KPA to K3 Aux Cable and PWR-US240 US 240V
Power Cord. Latest firmware installed, cosmetically good, operates full
output. No issues - includes manuals, spare fuses, and a new $37 box
from Elecra
TUNER SOLD
On 12/21/2016 3:21 PM, 'DGB' wrote:
Elecraft KPA500 Amp - Bought new as a kit 8/01/2012 s/n 0971-
assembled by myself. Includes KPAK3AUX-KPA to K3 Aux Cable and
PWR-US240 US 240V Power Cord. Latest firmware installed, cosmetically
good, operates full output. No issues - includes ma
Mike,
I would really love to know a bit more about your super-portable digi-station -
is there a guide or blog post online somewhere that explains what you've got
set up on the Pi etc anywhere please?
I assume others on the list may also be interested...
73, and a firm left handshake,
John (XL
The iMic is very good. There are also some quite small devices from
China which all look similar but are of varying quality. The Daffodil
US01 is one of the better ones. It is available on eBay or from amazon.com.
73, Bob N7XY
On 12/22/16 5:24 AM, Richard gillingham rmoo...@bellsouth.net [
Sole source appears to be: http://darcverlag.de/LINGUA-Sprachextractor
Bill W2BLC K-Line
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailma
On Thu,12/22/2016 3:59 AM, Bill W4ZV wrote:
Another reason to run higher voltage is improved IMD performance on SSB
transmit. Lots of info available from previous threads. I've been running
14.5 at the K3 terminals on multiple units for over 5 years with no
problems.
Bill,
IMD also affects C
"A thicker wire
would certainly require less voltage than
14.6 and that's what I am going to look
into."
Another reason to run higher voltage is improved IMD performance on SSB
transmit. Lots of info available from previous threads. I've been running
14.5 at the K3 terminals on multiple units
33 matches
Mail list logo