It sounds like Wayne understands perfectly. Increasing the CTS count
from the K-Pod adds more data load on the RJ45 port, and there may be a
question as to whether the port can handle that increase.
73, Dennis NJ6G
On 10/8/2018 09:05, Art Suberbielle wrote:
Wayne,
In reading your reply I th
THIS IS OUR SPECIAL 14TH ANNIVERSARY SPRINT AND INCLUDES A GREAT PRIZE DRAWING
FOR ALL MEMBER/PARTICIPANTS.
DATE: OCTOBER 10, 2018 (The evening of Wednesday the 19th in North America.)
TIME: 0030-0230 UTC
BANDS: 80, 40, 20 (See the General Instructions page for suggested
I normally start with the IF NB OFF. Turn on the DSP NB and adjust the
level for what I feel is optimum effect. Then remember the ## and set
it to OFF. Then turn on the IF NB, set it to what I feed is optimum
effect. Then go back to the DSP NB and set it to the previous value.
Best done wh
Mike,
If your noise source has changed, that is adequate reason the NB does
not work as it used to. With NB and NR there is no one solution that
fits all noise sources. You will just have to experiment a bit to see
which settings are most effective.
73,
Don W3FPR
On 10/8/2018 1:46 PM, Mik
I have 2 K3 and a K3S and for some time I have noticed all 3 doing something
that seems incorrect. All the radios are all up to correct Rev levels. For
years with my normal local noise, I always ran the NB at IF Nar 1-4 most all
the time with good success. In recent months, maybe more, on Nar
I have 2 K3 and a K3S and for some time I have noticed all 3 doing something
that seems incorrect. All the radios are all up to correct Rev levels. For
years with my normal local noise, I always ran the NB at IF Nar 1-4 most all
the time with good success. In recent months, maybe more, on Nar
On 10/8/2018 6:39 AM, Bill Stravinsky via Elecraft wrote:
If there is no way for you to send band data from the kx3, the kpa1500 should
change it's band with one transmitted dit,
Or a tap on the mic.
73, Jim K9YC
__
Elecraft maili
Wayne,
In reading your reply I think perhaps you are misunderstanding exactly what
we are hjoping to see in new software for the K-Pod.
We want the K-Pod to use the same CTS as the VFO A. E.G. 200 CTS on VFO A
and 200 CTS on K-Pod. At present, the K-Pod turns at 50% of what is set on
VFO A.
Hope
Pete,
Intermittent operation usually means a marginal connections somewhere.
Does your K3 have the gold pins on the Front Panel? If not, I suggest
that you change them.
To test whether the front panel to RF Board pins are the problem, remove
the front panel assembly and plug it back in. If
Eric,
There is no quick and easy path to do that. Your easiest solution is
just to let the KPA1500 auto-select the band. It has frequency sensing
and just a brief burst of RF will cause it to change bands.
A more indirect solution is to use a band decoder like the Elecraft KRC2
which will
If there is no way for you to send band data from the kx3, the kpa1500 should
change it's band with one transmitted dit, same as the Acom2000a.
BillK3WJV
On Monday, October 8, 2018, 7:48:32 AM EDT, eric norris via Elecraft
wrote:
Is there a way to send band data from the kx3+kxpa100 c
My K3 has begun experiencing intermittent loss of speaker audio. It
occurs without warning, typically while I am operating but *not* in
conjunction with events such as PTT or CW keying. Physical connection
to the speaker seems fine. It also recovers spontaneously, sometimes.
Headphone audio
Is there a way to send band data from the kx3+kxpa100 combo to the kpa1500? I
keep forgetting to change bands.
73 Eric WD6DBM
Sent from Yahoo Mail on Android
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraf
Hi all,
no, it is not the message about some issue...
I would like to just share the experiences with KX3 receiver which is
working like champ.
I was able to compare it with some big Icoms during my business trip last
weeks and I was
completely shocked. Several stations on 20m CW were simply not
14 matches
Mail list logo
