Hi friends, is anyone with experience working the Elecraft K3s with a
linear amplifier Kenwood TL-922 or with a linear amplifier Drake L4B?
Has anyone used the AMERITRON ARB-704 Universal Amplifier Interface to
connect the K3s to any of these linear amplifiers?
I appreciate any information about it
If I am reading correctly in Fred's book. I can connect the *CBLP3Y
cable to a USB to RS232 adapter to my computer which would create a
second comport from the radio to my computer. For example (if I am
reading correctly)*
*The USB port could be used to for audio codec and rig control (whi
Found the answer after doing a little more digging. This is a function of
the CONFIG:LIN OUT:2 (or REV) setting, which was defaulted to 30 on my
K3S. Setting this to 0 eliminated the Line Out monitoring of Line In.
This is discussed in the KE7X K3S book at the bottom of page 210.
The explanation
Got a great tip from Elecraft support on this one, which I'll relate here
for the next person who is searching for K3/K3S "T>R Latency measurement
timeout" on Google or the list when operating with Winlink.
The answer is to assign CONFIG:SYNC DT to a PF button (I used PF1) and then
enable it when
First, I'd have to ask why are you using VOX? I find that CAT control
is 100% reliable and is equally as fast or faster than VOX. Just be
sure the DLY control on the Signalink is set fully counterclockwise.
Likely your VOX level is too high and AntiVOX level is too low. I'd
opt for CA
In addition to Dick's advice, while viewing the ports, make sure "Show
hidden devices" is enabled. Windows 10, I guess driven by Microsoft's
infinite wisdom, will sometimes change a USB port assignment, but not
totally remove the former assignment. It then shows up as in use when
the ports ar
Is MAIN: MIC SEL set to LINE IN, and MAIN: MIC+LIN set to OFF?
Dennis NJ6G
On 10/11/2018 14:50, Paul Taenzer wrote:
I'm having a peculiar problem that I wonder if others have had and resolved.
I'm using a K3 and SignaLink USB interface and WSJT software running FT8
with the current version of
Just got this update in my ARRL Letter. Key points:
• The Hurricane Watch Net (HWN) resumed operations Wednesday morning
and will remain active until further notice on 14.325.00 MHz and 7.268.00 MHz.
• WX4NHC, the Amateur Radio at the National Hurricane Center, is active
to rece
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: ht
I'm having a peculiar problem that I wonder if others have had and resolved.
I'm using a K3 and SignaLink USB interface and WSJT software running FT8
with the current version of WSJT-X.
The issue is that the VOX triggers momentarily at the beginning of each
receive cycle.
I'd be grateful for any
When calling to connect with winmor you will always get the timeout
message until the called station responds. Once it connects the error
message should go away. It drove me nuts for a while. :-) FWIW, I use
the CAT command option for PTT so I don't have to remember to set the
PTT-KEY menu.
Carter:
COM3 is sometimes used by internal modems, and there may be a conflict
there. Has Windows been updated recently? Sometimes COM port assignments
change without warning.
Remove the USB connector from the computer. Then use Windows's Device
Manager (a control panel applet), and open the
The Hurricane Watch Net was active most of yesterday on 14325 and 7268.
They were soliciting and passing weather observations from the area.
Very well organized and directed nets. I'm not hearing them this
morning on 20m but it may be propagation conditions. See here for more:
http://www.ar
For some reason I can no longer connect my KX3 to my computer. I have tried
rebooting. changing the connection cable from my computer to the back of my
KXPA100 amp, and so forth.
Usually I have been using COM3, but I get a message that that com port is
in use by another device. Hmmm... It was work
AmRRON activated 10/09 1400Z - see amrron.com for activation information.
John/kn0cw
On 10/11/18 9:37 AM, Wayne Burdick wrote:
> Hi all,
>
> I heard an NPR interview with the city manager of a small town in the Florida
> panhandle this morning. He said that many nearby towns have zero
> comm
FWIW, I did some more poking around. Increasing the RF gain to present
Winlink with a louder signal helps to alleviate this problem. Looking at
the meter in Winlink, when it switches from TX to RX, there's some ramp
time before it reflects the full amplitude of the incoming signal.
Curious about
Hi all,
I heard an NPR interview with the city manager of a small town in the Florida
panhandle this morning. He said that many nearby towns have zero communications
right now, and he was “hoping to be heard” via radio. They’re pretty desperate.
Cell towers and landlines are down. They can’t ev
Eddy,
How much less than 100 watts. You can figure there may be an up to 20%
error in the KXPA100 wattmeter reading - which will vary from band to
band. Are you seeing at least 80 watts? If so, it may be that all is well.
73,
Don W3FPR
On 10/11/2018 8:20 AM, Eddy Avila wrote:
I bought us
I bought used the KXPA100 with ATU. The KXPA100 puts out less than full
power on 30 and 15 meters. The other bands the KXP!00 puts out 100 watts
and a bit more.
Both thte KX3 and the KXPA100 have the latest firmware installed.
This according to the LED's on the amp and connected to an MFJ dummyl
19 matches
Mail list logo