Anyone have a K-POD the6 are not using and would like to sell?
Marv
KG7V
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
Looking for a nice P3 with or without the P3SVGA option. Must have a CBLP3Y
cable as I don’t know how readily available they are at Elecraft. Please
reply directly to me via email.73 and good health, Lou W0FK
--
Sent from: http://elecraft.365791.n2.nabble.com/
Ya that’s a good. Point. Do you have any KX3 full packages ready to sell?
Fully loaded with the heil headphones??? Do ya ?
Sent from my iPhone
> On May 19, 2020, at 19:39, wbush68 via Elecraft
> wrote:
>
> Surely with all the K4 anticipation, one of you brilliant and good looking
>
Surely with all the K4 anticipation, one of you brilliant and good looking
gentlemen must have an excess to your needs KX-3.It doesn't hurt to
askThank you,Bill bushkd8jxjwbus...@yahoo.com
__
Elecraft mailing list
Home:
Does anyone happen to have a P3SVA not being used? I'm looking for one.
TNX Will WC2L
--
William Liporace WC2L
http://www.wc2l.com or http://dxc.wc2l.com
AR-Cluster Node telnet dxc.wc2l.com or 144.93 MHz
w...@wc2l.com
__
Elecraft
Sorry. Was in the middle of something, and had a brain f*rt.
Anyway, no, works the same — the spectrum continues to be displayed (frozen) in
the bandwidth window with the cursor. It does not disappear.
I’m on the latest firmware. If there’s a menu function that would affect that
(can’t
On the PX3 a solid green band displays the current bandwidth of the RX filter.
While receiving the spectrum is displayed over this block. When I go to TX the
spectrum on top of the green filter display disappears and only the green
filter block is displayed. The spectrum outside of the
One thing to remember, when you change the spkr+ph yes/no there is a
DELAY (in one direction) for several seconds as this is a soft-switch to
the BRAIN.
So wait a bit when you test this!
Also, Try the PH.R + -- in the other setting and then test the above
again, waiting for the delay.
**In
Not sure what you mean by “current filter display” — on the PX3 (?). The PX3
works exactly like the P3 — during transmit, the PX3 display freezes in place.
Nothing is covered by a solid color. I’ve never seen it do what I think you are
describing.
Have no idea why that might be happening.
On my P3 connected to my K3S when I transmit the display is frozen and shows
the last spectrum.
I just noticed that on my PX3 connected to my KX3 that during transmit the
current filter display covers the spectrum with a solid color.
This does not matter much but I prefer how the P3
it was the rj falt silver cable or connectors changed it now all
is good
On 5/19/2020 12:18 PM, Bill Steffey NY9H wrote:
no fwd power , full swr and the first led in thwsr display is
on fulltime, when that sensor is selected
gott dig in and pull that sensor
ideas ...
no fwd power , full swr and the first led in thwsr display is on
fulltime, when that sensor is selected
gott dig in and pull that sensor
ideas ... while I dissect///
bill /3
--
This email has been checked for viruses by Avast antivirus software.
"The information sent by the K3(s) is needed, hence the need to connect
(somewhere) to TXD info from the K3(s). "
I suspect that signal name "TXD" may be being misused in this discussion.
Having been caught by this I prefer to use the terms "data out" and "data in".
On a TS-590S COM port pin
Doug,
I have SN 00020 which is a field test model, and I suspect that it is
not much different than Wayne's SN 1.
The boards are relatively clean, and I do have all the FT mods (not
many) plus all the K2 A to B mods installed. Most of the FT mods were
component value changes.
There are
It would be great to see a picture of the circuit boards of that radio!
Taking into account 20+ years of of ECOs and experimental mods, I am
visualizing lots of jumpers and random capacitors…
Doug, w0uhu.
Message: 8
Date: Mon, 18 May 2020 12:43:36 -0700
From: Wayne Burdick
Hi Lou,
The information sent by the K3(s) is needed, hence the need to connect
(somewhere) to TXD info from the K3(s). (could be at the P3 as well)
A separate CAT/logger program is not needed to invoke K3(s) info to be send
Using the K3(s) Auto Info setting in the Config menu assures that the
Is that connection needed? If it is connected, might it obviate the
need for a separate CAT program?
If the SteppIR controller is connected in parallel with a computer
the TxD line *must not be* connected as it will load the TxD output
of the computer and *neither* device will be able to poll
The "official" SteppIR cable schematic also shows that Pin 3 (TXD out on the
K3S's RD232 DE9) is also to be connected.
https://groups.io/g/steppir/files/Controller%20Cable%20Schematics/S-26_21-6026-01%20Cable,%209%20pin%20FM%20to%20Male%202%203%205.pdf
Is that connection needed? If it is
It’s a continuation of the IF from the radio. You can connect an SDR receiver
there for instance.
Sent from my iPhone
...nr4c. bill
> On May 19, 2020, at 5:19 AM, "a4...@sy-edm.com" wrote:
>
> I see on my P3 that there is an additional BNC output, which is
> “un-buffered”….
>
> Is there
I see on my P3 that there is an additional BNC output, which is “un-buffered”….
Is there any way I can use this ?
What actually is in this output I/Q only - or RF
More curious than anything …
Regards
Tim
__
Elecraft mailing
Can't image why not. Hihi
Hope everyone is well on the left coast, well everywhere!
Let's beat this crap and get back to FB.
73 all
Dean K2WW
On Mon, May 18, 2020, 15:44 Wayne Burdick wrote:
> I have K2/10 S/N 1, but I'm not sure I want to part with it.
>
> Wayne
> N6KR
>
>
> > On May
21 matches
Mail list logo
