I was not pleased with the original Elecraft supplied power cord either. I
replaced it and never looked back.
Sent from my iPhone
...nr4c. bill
> On Sep 7, 2020, at 11:03 PM, Terry Brown wrote:
>
> I first want to thank all those who responded to my post. In a follow up
> email it was su
I first want to thank all those who responded to my post. In a follow up
email it was suggested that I check for voltage drop in the Elecraft 12v fused
power cord.
Sure enough, at key down, voltage dropped from 14v to 10.5v. I connected a
10ga power cord directly from my PS to the amp.
Thanks to all for checking in.
WM6P STEVEGA K3S
KB9AVOPAUL INK3S
WB9JNZERIC ILK3
NC0JW JIM CO KX3
K8NU CARL OH K3S
N8SBE DAVE MI K3S
KD8DZ MIKE OH K3
AE6JVPHILNH
When I purchased my K3 from a gentleman upgrading to the K3A he included
a PR 6 preamp. Rich would not transfer ownership until he knew
"everything was up to date and to factory specs". (Like to deal with him
- that is "his style"). He sent the rig and PR 6 back to the factory so
I believe the p
The K3 will allow Split in Data modes as well. But both VFOs must be in same
Mode/sub mode first. I
Sent from my iPhone
...nr4c. bill
> On Sep 7, 2020, at 9:52 AM, w4sc wrote:
>
> Bill,
>
> The K3 only allows the “split” mode for SSB and/or CW to be enabled, at
> least from panel. Tryin
The K3 will allow Split in Data modes as well. But both VFOs must be in same
Mode/sub mode first.
Sent from my iPhone
...nr4c. bill
> On Sep 7, 2020, at 9:52 AM, w4sc wrote:
>
> Bill,
>
> The K3 only allows the “split” mode for SSB and/or CW to be enabled, at
> least from panel. Trying
On 2020-09-07 at 14:35 Robert Rennard via Elecraft wrote:
I agree with Dave that we should start putting the Elecraft product model as
the first token in the mail header
This has, and still is a prerequisite nearly from the start of this list...
This is what Eric said about using this lis
Here is the list of stations checking in for the SSB Net last Sunday. Thank you
to the relay stations for their help in hearing stations that net control
cannot hear. Join us on 14.303.5 Sundays at 1800Z.
WB9JNZ
Call Name State Radio Serial # QRP
Hi,The Operators manual rev A7, says a minimum of 13.8 v to get !00 W output.
There have been several posts in the past that if the dc is less than 13.8
results in less than 100 w output from the KXPA100. 73Jim HK7SSS In a message
dated 9/7/2020 11:38:19 AM Pacific Standard Time, n...@comcast.ne
Have you done/redone the Power Output Display Calibration? See Appendix B in
the manual.
Grant NQ5T
> On Sep 7, 2020, at 2:35 PM, Terry Brown wrote:
>
> I have noticed over the past weeks that my KXPA100 will not put out any more
> than 70-80 watts when I am running my KX3 showing 100 watts o
Hmmm ... The International Morse Code is 1905 technology, and the
American Morse [Vail] Code is 1840's. You're suggesting we should all
abandon CW because it's old technology? [;=)
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
CWops #142
On 9/6/2020 7:06 PM, Barry wrote:
My point i
I have noticed over the past weeks that my KXPA100 will not put out any more
than 70-80 watts when I am running my KX3 showing 100 watts output. The
attenuator is not on. I have two antennas. One is a 3 element yagi that is
below 1.2:1 on all bands without the tuner, so when I tune, it just twea
Hey guys, I am seeing this behavior on my P3 and am wondering if this is how
it's supposed to work or or there is something wrong.
I set the REF LVL so I am just above the noise floor and then randomly a few
minutes later either the floor goes way down or way up. In other words, I
adjust the wa
No, that’s not it. The right is ALREADY in split mode when i attempt to use the
auto-tune.
You get the N/A flash if VFO A and B aren’t set to the same mode, other than
SSB/CW.
WSJT-X sets it up correctly, with both VFOs in DATA mode.
> On Sep 7, 2020, at 9:50 AM, w4sc wrote:
>
> Bill,
>
The K3 allows split in data modes, but only provided both VFOs are already
in data mode. The K3 will not allow cross-mode split between Data and
CW/SSB.
If you are seeing "SPL N/A" when you try to enable split with VFO A in a
Data mode, what that tells me is that VFO B is in CW or SSB, not in Data
Thanks for the bandwidth.
73, Donald K6RV
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.
FS - LP PAN 2 with K3 crystal SN 02964
Excellent condition, no scratches or dents. ASUS XONAR U7 included.
$100 shipped CONUS. Contact off-list
Bret/N4SRN
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home
I use Thunderbird for my email.
I filter almost everything into one folder or another. Works great
I filter[Elecraft] and {Elecraft-K4] with any K4 "stuff" in the subject
line, into a K4 folder. *It could just as easily go into the trash...*
Thunderbird does this automatically about every 10 mi
Bill,
The K3 only allows the “split” mode for SSB and/or CW to be enabled, at least
from panel. Trying to enable split in any other mode, the VFO B window flashes
“N/A”. You may have different indications / results if the split command is
sent via the CAT, and a mode other than CW or SSB is
I subscribe to about two dozen email reflectors, this one being the only
one that is not on groups.io.
I think a move is long overdue.
Björn SM7IUN
Den mån 7 sep. 2020 kl 14:36 skrev Robert Rennard via Elecraft <
elecraft@mailman.qth.net>:
> I agree with Dave that we should start putting the Ele
*K2/100*
*Includes :-*
*KPA100 Amp*
*KAT100-1 Tuner*
*KSB2 SSB*
*KNB2 NB*
*MH4 Mic*
*K160 RX*
*Complete with cables & manuals It is set up as the twins.*
*Asking $1000 + shipping (firm)*
*73, derek KD3GZ*
__
Elecraft mailing list
Hom
Hello,
I have a K3/0 and a Microbit RRC1258 Mk-ii-s for sale.
$600 post paid CONUS.
Thanks,
Raj, N2RD
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailt
I agree with Dave that we should start putting the Elecraft product model as
the first token in the mail header; e,g, K4, and stop lazily recycling a prior
header with a totally different topic in the body. Of course, worse yet is
somebody responding to a digest such that we get the entirety o
I use Nabble, too. It's better than email, but it's been broken for years.
Often, responses to a topic is split from the original, and 99% of posts
wind up in the main section, rather than parsed to the subheadings by radio.
Barry W2UP
John_N1JM wrote
> I use and go to Nabble. No emails from t
I have a KX3, sn 6474, that was mostly used as the tunable IF for 10GHz and
up contests. In 2017 it developed a fault with the external TX control
line.. This occurred just before the 10 GHz and up contest and I ending up
buying a new KX3 and sending this one back to Elecraft for repair. It has
sa
25 matches
Mail list logo