Your indignation is completely misplaced. Read the thread title. He's
trying to interface to a KAT500, and last I checked Elecraft makes those.
Dave AB7E
On 5/5/2022 2:16 PM, Ray wrote:
Did Elecraft make a FTdx Series of Radio Equipment ???
I Must have missed it. Did I sign in to the
I’m a relatively new owner of a new KAT500 and KPA500 Power Combo. I’m also an
Apple Mac user. When changing bands, the amp has been faulting. I then re-tune,
put amp back in ‘Oper’ mode and I’m good until I change bands again. I reached
out to support and they had me check the ‘Amp Key Interrup
A few years ago, someone had supplied PC boards to the Elecraft
reflector, that would replace the KANT3 and provide for two antennas. I
got one and it works great.
I wish I had more of them! As far as I know they are no longer
available. It was a one time thing.
Dave K1WHS
On 5/4/2022 11:
Come on Ray. This is an Elecraft forum. The man has Elecraft equipment.
What's the beef?
Wes N7WS
On 5/5/2022 2:16 PM, Ray wrote:
Did Elecraft make a FTdx Series of Radio Equipment ???
I Must have missed it. Did I sign in to the Wrong thread………..
Ray WA6VAB Elecraft K3
From: Joe Subi
One thing that you may not understand is that MAN with BYP active is the same
electrically as BYP mode).
I use all 3 ANT ports of my KAT500 and never used any KAT mode except MAN. Some
of my antennas work fine in MAN/Byp and others require some help with L and/or
C. All antenna switching is au
No, but Elecraft makes the KAT500, and Greg is using a KAT500 with their
FT-DX10.
On Thu, May 5, 2022, 17:16 Ray wrote:
> Did Elecraft make a FTdx Series of Radio Equipment ???
> I Must have missed it. Did I sign in to the Wrong thread………..
>
> Ray WA6VAB Elecraft K3
>
>
> From: Joe Subich, W
Did Elecraft make a FTdx Series of Radio Equipment ???
I Must have missed it. Did I sign in to the Wrong thread………..
Ray WA6VAB Elecraft K3
From: Joe Subich, W4TV
Sent: Thursday, May 5, 2022 12:39 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KAT 500 and the Yaesu FTDX10
To whi
When I got my KX3, I positioned it as outdoor use. The options I got at the
moment were KXFL3, KXAT3, KXBC3 and MH3.
When I got K3 as my main TRX, I repositioned the KX3 as both a back up TRX to
K3 inside shack and the outdoor use. So, I got KXPA100.
Later, I added KXPD3 for easy CW operation on
Your request can be attained by use of the KAT500 Utility to configure
each antenna or antenna port per band as needed.
I use Ant 1 and Ant 2 for my wire antennas, 160M - 10M and Ant 3 for my
6M yagi in bypass mode. After setting up the KAT500 via the Utility,
and training the KAT500 for the
To which connector did your KAT500/FTdx1200 tuner cable attach?
The Tuner jacks are the same on both FTdx1200 and FTdx10 as are
the "Linear" jacks.
73,
... Joe, W4TV
On 2022-05-05 3:17 PM, Greg Chartrand via Elecraft wrote:
I just purchased a ftdx10 and wondered if the band data cable
I ordered the "kit" version when the first one's were offered (sn 475).
I got everything except paddle (not a CW operator) or the battery
charger (use either external battery or use it mobile/in shack).
I did get the 2m module as 144 is IF of my mw transverters (1w drive
level) where SSB is p
I just purchased a ftdx10 and wondered if the band data cable is the same as
the one I had with my old ftdx1200.
Thanks,W7MY-Greg ChartrandRichland, WA.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/li
Mike -
I leave my KAT500 set in Manual mode at all times. On bands where the SWR
on my EDZ is acceptable (based on the SWR Threshold I have set for Bypass)
it switches to Bypass automatically. It will switch back, if needed, when I
change bands.
Firmware ver. 02.05 (but I think it has always wo
Hello Elecrafters,
I am running a K3-based K-Line: K3-P3-KAT500-KPS500.
Currently, I have two antennas connected to my KAT500: ANT 1 is my SteppIR
40/30 3L, and ANT 3 is my 160M/80M dipole.
When I have my K3 select 40M/20M/17M/15M/12M/10M/6M, my KAT500 is in BYP
mode and ANT 1 as expect
14 matches
Mail list logo