Re: [Elecraft] KX3 Controlled Envelope SSB

Hi Scott, This is possible, and it's already wish-listed. Our DSP resources are tied up at the moment. 73, Wayne N6KR > On Mar 21, 2023, at 2:42 PM, Scott Zastoupil via Elecraft > wrote: > > So I have to ask since I have not seen any activity since 2016. Is it > possible to have

[Elecraft] KX3 Controlled Envelope SSB

So I have to ask since I have not seen any activity since 2016.  Is it possible to have Elecraft provide a KX3 software update to implement CESSB to the KX3? It would be nice to have the extra ~3dB to the rig for POTA activations.  I would imagine it would be a nice bullet to add to the

[Elecraft] FS K3/P3 Make offer

Reposting. Make offer. Please reply ONLY off list. For Sale: K3/100 and P3 Configuration details listed below. Can be shipped or pick up in West Los Angeles near Santa Monica Airport. Thanks - Steve WB6RSE K3/100 Five 8-pole filters: 2.8, 1.8, 1.0, 500, 250 KAT3 ATU KBPF3 General coverage RX

Re: [Elecraft] [Elecraft-K4] KPOD intermittent

Jim, I have two K-Pods which are used with my K4Ds and previously K3s. I too on occasion have trouble with the switches. I have noted that rebooting the K4D will often cure the problem.Also I wonder if having the switch react to both momentary tap and sustained push beyond a second

[Elecraft] KPOD intermittent

I really like the KPOD...when it works. I find the buttons occasionally non responsive resulting in nothing being sent. After a few taps it eventually works again for a while. Of course this mostly occurs when trying to send a call in a pileup or a reply 599TU. Is this a button thing that needs

Re: [Elecraft] KAT500 - can't change antennas on 6 meters

I'd still suspect the config settings, this test just showed that the KAT-500 is doing well mechanically. The tuner is getting a signal from the K3 telling it what band you're on so appears to be limiting your options based on that band. You can repeat the mode/ant test with the radio off, you

Re: [Elecraft] KAT500 - can't change antennas on 6 meters

Dennis Thanks for the suggestion. Good test. It turns out that Yes, I can change antennas now on 50 MHz when I disconnect control cables. H. I reconnect the control cables, and the symptom of not being able to change to antennas other than antenna 3 on 50 MHz, returns. So one

Re: [Elecraft] KAT500 - can't change antennas on 6 meters

With power only, no control cables plugged in so it's essentially isolated from anything external, are you able to switch between modes and antennas? Dennis NJ6G On 3/21/2023 09:43, JK Hooper via Elecraft wrote: Hi all, Despite my making what-I-think are appropriate changes in the KAT500

Re: [Elecraft] KAT500 - can't change antennas on 6 meters

I had something similar on my KAT-500 where I could not get to antenna connection 3. What I did was to do the update of the software and then open it to manually turn on antenna 3 and it was fine. I have the cable if you need to do that. On Tue, Mar 21, 2023 at 11:45 JK Hooper via Elecraft <

[Elecraft] KAT500 - can't change antennas on 6 meters

Hi all, Despite my making what-I-think are appropriate changes in the KAT500 utility (MacOS version), I am not able to switch antennas for 6 meters (50 MHz). KAT500 always stays on Antenna 3. My work-around solution has been to put my antenna w/ 50 MHz capability on Antenna 3. Any

[Elecraft] QST - My new book about CW and Morse Code

Greetings. I'd a daily reader and occasional poster to the group - K#, KX3, KAT500, and KPA500. Forgive the commercial interruption, but I wanted to share that my book, The CW Way of Life, is now available on Amazon. https://amzn.to/3ltqzBo I announced it a couple of weeks back on the LICW and