[Elecraft] Milliwatt Drive Power for Transverters

I have a Q5 Signal 100W transverter. The required drive power, 1mw, for full transverter output, is set in the “L” range of the K3 XVx PWR config option. When I vary the drive power from 0.1mw to 1.5mw, there is no change in the output power of the transverter indicated by the in-line analog

[Elecraft] DELUXE ELECRAFT POTA STATION FOR SALE

I have the following gear for sale: KX3 SN 9986, with all options (except extended band modules) auto tuner, filters, etc. latest firmware, Excellent Condition $1,200 K1 with auto tuner, KFL1-4 Four Band Filter Board, Backlighted LCD, PC Board Rev. E, original owner’s manual in excellent

Re: [Elecraft] Elecraft CW Net Announcement

Good morning Kevin. 15 degrees here in WNC! I tried to play the videos but no joy. Is there something special I need to do to play them? Tnx es 73, David, NS4V > On Mar 12, 2022, at 10:02 PM, kevin wrote: > > Good Evening, > >The sun is acting up. We are due for some effects from a

Re: [Elecraft] K3 drive level for Q5 Signal 432 Transverter

Tried what you suggested Gary. No joy. The upper limit with the PWR knob remains at 0.8MW. I can adjust downward but not upward. Need to get a good power meter on it and see what the actual output is. And, I’ll try the low-level power calibration process and see what happens. Thanks

[Elecraft] K3 drive level for Q5 Signal 432 Transverter

Using the Config Menu, I have set the drive level at the maximum for the transverter at 1 MW. However, when I check the drive from the front panel PWR knob it reads 0.8MW and I cannot adjust it any higher with the knob. Nothing I do seems to change the the PWR knob drive level. I am running

Re: [Elecraft] Mac RTTY Software for Elecraft radio's

Check out the N3FJP ACLogger. It is excellent for general logging plus multiple ’special’ logs including the CQ WPX logger which I ‘assume’ would include all modes. Good luck! David NS4V David R. Hourdequin, PE 828-421-6216 d...@dremy.com www.dremy.com > On Feb 7, 2022, at 12:52 AM,

Re: [Elecraft] OT Donating Surplus Gear

More of us need to be doing more of ’this’! Thnaks for the inspiration Paul! 73, David, NS4V David R. Hourdequin, PE Heavy Timber & Glulam Engrg P.O. Box 1399 Hayesville, NC. 28904 828-421-6216 d...@dremy.com > On Jan 11, 2022, at 8:32 AM, Paul Huff wrote: > > With my wife’s encouragement, I

[Elecraft] K3 HM2 hand mike hum

When I key the mike, my friends hear a hum on my signal that is not there when I use the Heil Proset K2/K3. I hear the same thing when I monitor my signal on the KX3. I’ve checked the connections at both ends and do not see anything amiss. At the mike end, the ground wire is ‘floating’ and

Re: [Elecraft] KX3 - Holding Power Output at Set Value\

out there. > > 73, > Scott N9AA > > > On 12/7/21 4:16 PM, David Hourdequin wrote: >> I am in the process of getting familiar with my newly acquired KX3 purchased >> for POTA and am enjoying it immensely. >> >> I am powering it with a 14.8V, high qualit

[Elecraft] KX3 - Holding Power Output at Set Value\

I am in the process of getting familiar with my newly acquired KX3 purchased for POTA and am enjoying it immensely. I am powering it with a 14.8V, high quality, Yamaha walwart - very little internal noise. Settings indicated in the VFO B display area using DISP are normal. When I set the PWR

[Elecraft] K3 with external 432 transverter

I have a new Q5Signal 432 100w transverter all hooked up, did all the appropriate settings on the K3 (I think) but K3 is not ‘hearing’ through the transverter nor is the transverter being driven when I key the mike although the transmit light is on when I do key it but no output power LED’s are

[Elecraft] K3 with Q5Signal Transverter

Anyone have experience using the K3 with the Q5 Signal Transverter. I’m considering the purchase of their 50w model.’ Thanks so much for any ideas/suggestions, etc. David, NS4V David R. Hourdequin, PE Specialty Engineering Heavy Timber - Glulam SIPs - CLT Engineering P.O. Box 1399 Hayesville,