My k3 keeps losing its mind. One day it won't transmit SSB - I can whistle
up 100W but speech gives 5W of avg and ~15W peak.
On another day it says "KAT500 not turned ON". I have a KPA500 but no
KAT500.
My fix for both these has been to do a factory reset and reload my last
saved configuration --
Been waiting over a month for a reply from Elecraft:
"SSB problem: very little output, 2-5W peak when set for 100. ALC reads
full scale regardless of MIC setting, nil @<2. Tried two microphones. If I
whistle, I can get full output. All this independent of compression.
on CW: first dit after a
I cannot operate FT8 on 80 60 40 30 or 12m. It works fine on the other
bands.
Data mode (usb) is selected on all. However, on the P3, the filter window
is displayed improperly on the bands that don't work -- it is centered on
the display and is actually LSB because I can ALT the mode and copy FT8
Rear panel mic input, electret mic. Mic+Lin on. VOM shows 8V across mic
element. Tried several mics.
VOX works on CW, not on SSB. What am I missing? It used to work.
No biggie, I'm a CW guy but FD is coming up.
--
Dick - K4XU
__
I'd like to thank W4NZ and DL5RBW who correctly identified the problem as a
bad FET in the LPA.
Identification and replacement of the offending part (a G-S short) took
only a little longer than that needed to remove and replace the bottom
panel.
73,
--
Dick - K4XU
Okay, I need to be more specific about my "bad audio".. The audio is raspy,
like it has rf in it. It is independent of frequency, power, mic type,
recorded or not, Hi or Lo mic gain setting, and mic drive level.
The only other issue I have is that the low power carrier is 5W when the
PWR is set
I had several "Bad Audio" reports in SS. One I can Ignore, more than that I
believe.
I have a K3 with the recorder. To test it, I ran the K3 into a dummy load
and listened to the tx signal on another receiver. The resulting signal was
indeed crappy both with the mic and on recording.
I reduced
ready to install KSYN3A. trying to upgrade MCU as instructed with K3
utility v 1.16.7.25.
Present MCU is v 4.83.
Clicking Check for revisions now, and it says only 4.83 is available.
How do I get 5.14?
--
Dick - K4XU
__
Elecraft
I'm trying to help a friend setting up his K3 for PSK with a Signal link
USB and HRD.
It goes into transmit but the output power is zero. If I turn the USB's tx
gain all the way up, I can hear some weak audio from the K3's speaker when
the ptt keys it to TX.
The mic+LIN is ON. What am I
I have blown up computer motherboard audio line inputs on three computers
and two USB audio adapter dongles trying to run RTTY or PSK.
The Line Out is set at nor 15. There was a direct connection from Line
out to the rear sound line in.There is a large ferrite 51 mix choke on the
cable. There was
Once, before my K3 lost its mind, if I keyed the VOX during the playing of
a recorded message, the message would stop. Now nothing but a button push
on REC will stop it. Rather unhandy for contest operating.
What am I forgetting?
--
Dick - K4XU
I am bringing up a new (to me) K3.
What makes the drive level track between bands without the nasty ALC
overshoots? The drive from the K3 sometimes also takes a while to settle
down when coming up on a new band. This drives me crazy in changing bands
and modes while chasing W1AW/# stations.
What
To all who responded, thanks.
CONFIG: Power by Band fixed the standby power issue and a recal of the TX
at 5 and 50W solved most of the rest.
73,
--
Dick - K4XU
__
Elecraft mailing list
Home:
Rule 1: NEVER use the POWER button to escape from the TUNE function. It
can cause your MCU to crash and lose its mind.
Rule 2: When reloading your MCU, make sure the 15pin ACC plug is
disconnected or the MCU will not initialize.
Rule 3: If you have your K3 all set up the way you like it, run
I was in the Tune mode. I accidently hit the Power button to exit. The
display went blank. Now nothing works. Removing power and restart with
Power button gets the blank screen. Help!
Dick, K4xu
__
Elecraft mailing list
Home:
I was on 160m in the Tune mode on my K3. I accidently hit the Power
button to exit. The display went blank. Now nothing works. Removing
power and restart with
Power button gets the blank screen.
Turning it on with the Shift/LO knob depressed brings up the meter and
bandwidth legends and EE INIT
--
Dick - K4XU
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this
the K3 firmware can reprogram the DVK button action. If the config
menu is open and you press a function key to send a DVK message, the voice
message button is over-written with the config menu item.
Yep, it does that. How do you correct it if you did it by accident?
How do you return the buttons
How do I teach my K3 to go back to 100W when the KPA500 is off?
Yes, the control cable is connected.
73, Dick
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
In last year's SSB SS, when my K3 was a month old, I used function key
macros from N1MM to
'hit' the message memory buttons on the panel.
Each was in the form of:
F1 CQ,{cat1asc swt39;}
F2 Exch,{cat1asc swt35;}
Now they do not work. Has something changed?
Using N1MM V10.10.1 on Com 1. nothing
Is it possible to search the Elecraft reflector archives?
I go to the archives and it seems you have to do it by month.
There's gotta be a better way.
--
Dick - K4XU
__
Elecraft mailing list
Home:
Is it possible to search the Elecraft reflector archives?
I go to the archives and it seems you have to do it by month.
There
--
Dick - K4XU
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
During the recent SS, I was having to change for LSB to USB or the reverse
every time I changed between 40m and 20m. SSB is not a major mode for me so
it was the first time in a contest. I looked through the book and could not
find anything about teaching it which sideband is prefered on each
Is it possible to buy a blank K3 box - one without any holes on the front or
rear panels?
I could not find anything on the site.
tnx,
--
Dick - K4XU
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
I'm a new owner, and new to the list.
The manual says:
FP ACC This connector (RJ-45, 6 pins) is located on the bottom of the
transceiver, near the VFO B knob. It is used with accessory devices.
What are these devices and how are they connected? There's no pin definition
or reference in the
25 matches
Mail list logo