Re: [Elecraft] K3 Utility vs. RemoteRig?

Rick, This is a bug in the K3 Utility that you and I reported to Dick to fix in February 2018. I am not sure where he is in getting this taken care of. 73, Mitch K7DX / DJ0QN -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109 Skype: mitchwo USA: Home:+1-239-221-9600 - Mobile:+1-424

[Elecraft] Looking for K3/0 mini or non-mini

For an OM in our remote group, I am looking for a used K3/0 (old) or K3/0 mini. If anyone has one available in either the U.S. or Europe, please contact me off list. 73, Mitch DJ0QN / K7DX -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109 Skype: mitchwo USA: Home:+1-239-221-9600 -

[Elecraft] 12V Plug on K3/0 Mini

I just bought a used K3/0 mini which hasn't arrived yet. Unfortunately, the owner no longer has the 12v cable for it. Could someone please let me know the type of plug (mm) on the 12v cable? I can't find this is the remote manual, but I know it is thicker than the one for the RRC. I will go by

Re: [Elecraft] Remote with Satellite

John, The latency is too high, around three quarters of a second, of which most (around 530 ms) is caused by the trip up and down to the satellite and back. The rest is internet latency of a couple of hundred ms. 73, Mitch DJ0QN -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109

Re: [Elecraft] K3/0 Firmware

Dennis and Hisashi, I have updated my K3/0 from time to time using the newest firmware for the K3. Just connect the PC directly to the COM port and the K3 Utility will recognize and update it. 73, Mitch DJ0QN / K7DX -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109 Skype: mitch

Re: [Elecraft] Tours?

Ken, Note that Watsonville is not exactly what one would call a side trip from L.A. It is somewhere around a 5-7+ hour trip one way, depending upon from where in that area you leave from, as well as the traffic. If you do make it, the people at Elecraft are super and will go out of their way

Re: [Elecraft] K3/0 Firmware

2018 22:39, Barry Baines wrote: Mitch: On Jul 26, 2018, at 3:45 PM, Mitch Wolfson DJ0QN / K7DX <mailto:dj...@gmx.de>> wrote: Dennis and Hisashi, I have updated my K3/0 from time to time using the newest firmware for the K3. Just connect the PC directly to the COM port and the K3 Uti

[Elecraft] Looking for a PR6-10

If anyone has a PR6-10 (not PR6) preamp that you no longer need, please send me an offer via direct mail. If you upgraded to a KXV3B and had one before, then you no longer need it. This can be shipped to an address within the U.S. or Europe. Thanks & 73, Mitch DJ0QN / K7DX -- Mitch Wolfson K

Re: [Elecraft] -Remote Rig "standard" with K3 and K3/0 mini

Craig, All RemoteRig RRC's are the same. Only the jumpers/straps inside need to be set and the correct cabling and programming used (see handbook). 73, Mitch DJ0QN / K7DX -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109 Skype: mitchwo USA: Home:+1-239-221-9600 - Mobile:+1-424-2

Re: [Elecraft] K3/RemoteRig Serial Question

Mike, The answer is found on pages 13 and 18 of the RemoteRig manual..NO. Just a tip; I suggest posing RemoteRig specific questions on their forum. 73, Mitch DJ0QN / K7DX -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109 Skype: mitchwo USA: Home:+1-239-221-9600 - Mobile:+1-42

[Elecraft] Looking for a PR6-10

I still need one more PR6-10 to replace the PR6 in another K3. If anyone has a PR6-10 (not PR6!) preamp that you no longer need, please send me an offer via direct mail. If you upgraded to a KXV3B and had one before, then you no longer need it (it is included). This can be shipped to either an

[Elecraft] Looking for K3/0 Mini and/or RRC

A local OM here in Florida is looking for a K3/0 Mini and RemoteRig RRC (control unit only!). If you have either a complete set (K3/0 Mini + RRK0CBL + RRC/control), or part of a set (e.g. only RRC/control or K3/0 Mini), please contact me off list. The OM is not on this reflector, so I will pass

Re: [Elecraft] new K3/0 Mini

Barry, I have been using serial to ethernet servers for over 10 years to control rotors, amplifiers and other serial devices. You set these up once and can forget about them. You install a virtual serial port on the control PC for which you can use any kind of client software to control that

Re: [Elecraft] new K3/0 Mini

:+49 89 32152700 - Mobile/WhatsApp:+49 172 8374436 On 28.02.2019 14:52, Barry Baines wrote: Mitch: On Feb 28, 2019, at 11:27 AM, Mitch Wolfson DJ0QN / K7DX wrote: Barry, I have been using serial to ethernet servers for over 10 years to control rotors, amplifiers and other serial devices. You

Re: [Elecraft] sharing K3 RS232 to CAT and Remoterig

Don and everyone, The RemoteRig  RRC actually provides a built-in method to provide this duplicate CAT data. Since the RRCs' COM2 are already occupied to tie the two ends together using CAT, all you have to do is to change each RRC's COM1 to mode-7. This will duplicate CAT over COM1 and you

Re: [Elecraft] Elecraft k3S and K3/0 Mini with remote rig

Ron, It is really very simple. There is a guide at: If you still have problems, drop me a direct mail. I can set it up using Teamviewer in about two minutes. 73, Mitch DJ0QN / K7DX -- Mitch Wolfson K7DX / DJ0QN 10285 Boca Cir, Naples, FL 34109 Skype: mitchwo