Wayne,
I read your reply to this thread with great consideration.
I think your observation that most field testers did not
adjust the AGC parameters is a good one.
However, I think that that K3--and the Elecraft product line
in general--particularly appeals to people who value amateur
experiment
Are there any field tester reports on subreceiver function and
integration?
N1KO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qt
Will the K3 instruction manual have appropriately placed
sidebars or cross references for installation of optional
accessories at the time of original build, or will the
assembler have to cross reference accessory manuals his or
herself?
N1KO
___
Elecraf
Does the K3's bar-graph S-meter have a function to momentarily
hold a bar at the 'peak' value?
N1KO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
P.S. I just realized there's a backup listhost server. Oops.
Original question still stands.
N1KO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Listhost archives seem to be down at the moment, so apologies
if the following question has already been asked:
Can Wayne, Eric or anyone else comment more on the KAT3
design? Specifically, how is the matching network configured,
is it "balanced" or "unbalanced" and is there any balun built-in?
With the K3 subreceiver installed and while using binaural
audio output from both receivers, is there a provision so that
a switch toggles between memory VFO A/B within one receiver,
and not between (physical) main- and sub-receivers?
Example: If working a split DX pileup, can you set one
receiver
1) Can the sub-RX receive off the same antenna as the main RX
at the same time?
2) Can the main-RX and sub-RX be used in any combination of
antenna inputs, including ANT1, ANT2 and RX ANT IN?
3) Can the sub-RX provide unbroken audio using any antenna
input while the K3 is transmitting?
4) Can th
I'm trying to understand the major intended uses of the
optional K3 second receiver. My understanding is that the
audio out from the second receiver will be cut while the K3 is
transmitting. Is the IF output port switchable between the
main and subreceiver? In other words, can a panadapter be fe
Hello again and happy holidays!
With regard to the K2 frequency stability...
Several good points were raised and I realized that I wasn't
adequately specific before. The drift I notice is primarily
related to warmup and not during normal operation. I will
perform the aforementioned test to c
Hi again,
As a few people pointed out, I misspoke in my earlier email.
When I calibrate C22 I immediately run CAL PLL and CAL FIL.
True, the K2 does not directly reference C22 during normal
operation. My calibration of C22 and then CAL PLL and CAL
FIL is all by-the-book.
That being said, I
Hello all,
I notice that on K2 #03547 rev B (with KPA100, KDSP2, KSB2,
K160RX and thermistor installed at time of build) the master
frequency drifts as a function of temperature. From an
ambient temp of 65F to max rig temp when the KPA100 fan
kicks in the receiver may drift by 800 Hz. The ra
Hello all,
I have a question for the gurus regarding fixing my K2. Back
in 2003 I built a K2 with KPA100, KDSP2, SSB, 160 mod and
external ATU and used it to operate mobile in South America
for a period of time. I then returned to the U.S. to begin
med school and have been off the air since. I'
13 matches
Mail list logo