Re: [Elecraft] K3: CW characters sound very hard / short

Hi, thank you very much for the feedback. I will pass on the information to my friend. He will then have to see how he proceeds. 73, Wolfgang DL2KI -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home

Re: [Elecraft] K3: CW characters sound very hard / short

LY" is set to "008". But on the basic problem this had so far no influence. I have therefore rather the assumption that here somewhere a hardware problem is present with this special K3. 73, Wolfgang Dl2KI -- Sent from: http://elec

[Elecraft] K3: CW characters sound very hard / short

setting possibilities to solve this issue, or can there also be a hardware problem here? 73, Wolfgang DL2KI -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailma

Re: [Elecraft] [K3] Wetting current and CW paddles

can't judge if this had anything to do with this topic. OK, I'll just leave it like this. Maybe somebody will have some experience with it after all. Thanks a lot Wolfgang, DL2KI -- Sent from: http://elecraft.365791.n2.nabble.com/ __

Re: [Elecraft] [K3] Wetting current and CW paddles

Hi, actually I expected a little discussion on a qualified professional level in this mailing list. Otherwise I would not ask here. But the topic does not seem to invite to it. 73, Wolfgang DL2KI -- Sent from: http://elecraft.365791.n2.nabble.com

[Elecraft] [K3] Wetting current and CW paddles

g and invites to observe the described effect. 73, Wolfgang DL2KI -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.ne

Re: [Elecraft] Elecraft K2 CW key shaping

Hi, thanks for the hints and information. I will listen to the signal once with my K3. That seems to be the best way to check the hint. But I will also have a look at the connector plugs and power supply cables in my portable configuration. 73, Wolfgang DL2KI -- Sent from: http://elecraft

[Elecraft] Elecraft K2 CW key shaping

A" is at my disposal, but I have little experience with measuring instruments, since I only use them occasionally. Thank you and 73 Wolfgang DL2KI -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home:

Re: [Elecraft] K-1 4-band Availability/Status?

/There is no need for the KFL1 firmware to be open source, it is available from Elecraft as a spare part. Elecraft will continue to support existing KFL1-4 boards with parts (except for replacement trimmer capacitors) for a good long time into the future. / Hi Don, when you allow an existing pro

[Elecraft] K3 Transmitter Gain Calibration fails

''. 5 watt calibration failed. Elapsed time: 6,0 secs/ The same with the 50W Calibration. Where is the problem? 73, Wolfgang DL2KI -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Transmitter-Gain-Calibration-fails-tp7599231.html Sent from the Elecraft mai

Re: [Elecraft] Err AT3

Hi Gary, i had the same problem a few weeks ago. Peter (DL2KI) by the German Elecraft service said that it might be a contact problem. I then removed the KAT3 and cleaned the contacts with a glass fibre brush. Then everything was OK. It could also be a contact problem on the connectors between

[Elecraft] K3 Eqalizer settings - another way

t; then. The "SWTxx;" command and the "DB;" command must be carried out in quick succession. In the 'Elecraft K3 utility", you can for example run a macro"SWT34; DB;" and then receive the related response string. This note for general information. 73,

Re: [Elecraft] K3 Eqalizer settings

Hi Tom, that's the idea I was looking for! Thanks, with this solution, I'll continue. 73, Wolfgang DL2KI -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Eqalizer-settings-tp7593506p7593511.html Sent from the Elecraft mailing list archive at

[Elecraft] K3 Eqalizer settings

Hi, a short question: How it is possible to GET the equalizer setting of k3. I experiment with the WA5ZNU "Python K3lib" and would like to add this new function. thanks 73, Wolfgang DL2KI -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Eqalizer-settings