[Elecraft] k3 meter display

Hi!. Just downloaded 0363. All seemed fine but now my meter display on cw wants to show only cmp[compression] & alc, instead of swr & power. I tried downloading again, but got the same result...The rig certainly seems to work fine. I just had Qso with CX2DDP [cw] in Uruguay with my puny screw

[Elecraft] k3 meter display

Thanks to N6ML, N4LQ, & W3FPR, My gosh , my subject heading even stated "k3 meter display" yet my brain failed the obvious...I hve sometimes read of such operator errors on this reflector-I now did it too. Yes, it was that simple-press the "disp" button. Thanks to the above and any others

[Elecraft] K3 serial 1216

This is a factory built[by Cody] K3 ordered Feb 16, 2008 received July 10. 2008. ATU, 2.7, 1.8 & 400 Hz filters with KXV3 transverter module. All seems to be working fine. Indeed, very good rig. Steve W6HPK ___ Elecraft mailing list Post to: Elecra

[Elecraft] K3 Af Mod kit

In the nov. 14, 2008 enchancements and Application notes applicable to this new kit, it states That " The headphone output of the K3, which uses a separate amplifier, already has a very low distortion output and is not impacted by these changes,"...Does this mean both the front panel and rear h

[Elecraft] K3 production schedule

Eric posted updated shipping schedule today, 1/21, on Elecraft's website. Production does seem to be really moving up. Steve, W6HPK ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info

[Elecraft] K3 nr. 365 arrived today

This is an assembled K3 with 6.0, 2.7 & .5 filters; also includes the general coverage RX module. All seems to work great. Ordered May 3 without deposit. Thanks to all at Elecraft, including Cody who built the rig. ..73 Steve, W6HPK K2 5039, K3 365 __

Re: [Elecraft] LP Pan versus P3 Panadapters

Hi Larry & all; I have not used Lp Pan so I cannot really make a comparison, but I have found that if the P3 ref level is set really low just at the noise level and if the span is set to narrow amounts that indeed very low level sigs can be seen. For example I hve been "seeing" the 20 meter b

Re: [Elecraft] LP Pan versus P3 Panadapters

Corrections: beacons at 14100 Mhz, not 14000 Mhz,,,Steve W6HPK - Original Message - From: shwha...@comcast.net To: Larry K1UO Cc: elecraft@mailman.qth.net Sent: Tue, 14 Sep 2010 16:22:46 - (UTC) Subject: Re: [Elecraft] LP Pan versus P3 Panadapters Hi Larry & all; I have not used Lp P

[Elecraft] K3 vs FT5000 TX audio

Some messages back[probably yesterday[ a Juergen{sp?] or implied that the Ft 5000 tx audio was clearly superior to that of the K3He was i believe referring to published numbers, probably those reported in QST. [ Of course the Sherwood numbers relate to the receivers only] I am not technic

[Elecraft] tx audio

Sri, I accidently sent the last unfinished letter. I presume the third -order intermodulation {IMD} should suggest the answer. Here i see that the Ft5000 is "better" than the K3, but only when the FT5000 is using class A modulation. One should expect lower IMD running Class A , right? Th

[Elecraft] KpA500 to K3 band change,fault/status

For you who will be soon getting a KPA500 to add to your K3, don't forget to download the latest firmware for the K3: MCU 4.36, DSP, DSP2.73. Probably most have already routinely downloaded these .Among other things, these updates enable the individual band buttons on the KPA500 to set the b