[Elecraft] K2/100 power-out change

Late TKS VM to all who replied. I have the two cal cables from one of the former owners, and will attend to alignment and other tasks real soon now, including RTM ;o) It's been busy around here earning a living, and I've not had the enthusiasm of my youth at work-day's end. 73, Dave, N3HE

Re: [Elecraft] K2/100 power-out change

;Elecraft Reflector" Sent: Wednesday, September 22, 2004 4:10 PM Subject: Re: [Elecraft] K2/100 power-out change Rich, Further to my earlier posting. The resistor to change is R98 on the RF board. I have changed mine from 270 ohms to 1200 ohms and that completely removed the power

Re: [Elecraft] K2/100 power-out change

ssage - > From: Rich McCabe > To: Elecraft Reflector > Sent: Wednesday, September 22, 2004 11:23 AM > Subject: Re: [Elecraft] K2/100 power-out change > > Sounds like both K2's I have had. 38xx and 44xx. The output jumps all over > the place. My amp does not like i

Re: [Elecraft] K2/100 power-out change

Rich, Further to my earlier posting. The resistor to change is R98 on the RF board. I have changed mine from 270 ohms to 1200 ohms and that completely removed the power hunting. Without doing this it is almost impossible to properly set up the KAT100 if you build one. Regards, Mike VP8NO ___

Re: [Elecraft] K2/100 power-out change

OK Folks, I found the info that Tom was referring to - it is in a reflector posting from Wayne Burdick dated 8/5/1999. I have appended the text to the bottom of this reply. 73, Don W3FPR - Original Message - It IS in the software ALC... reflects the ALC's attempting (at about a 1

Re: [Elecraft] K2/100 power-out change

G'day, > Sounds like both K2's I have had. 38xx and 44xx. The output jumps all over > the place. My amp does not like it either. When I posted about it, the > response I got was that is "normal". If this is the often reported O/P power change then yes this is "normal", however, it shouldn't be.

Re: [Elecraft] K2/100 power-out change

/k2vco - Original Message - From: "Vic Rosenthal" <[EMAIL PROTECTED]> To: "Rich McCabe" <[EMAIL PROTECTED]> Cc: "Elecraft Reflector" Sent: Wednesday, September 22, 2004 10:35 AM Subject: Re: [Elecraft] K2/100 power-out change Rich McCabe wr

RE: [Elecraft] K2/100 power-out change

om Hammond Sent: Wednesday, September 22, 2004 12:31 PM To: Larry Phipps; Rich McCabe; Elecraft Reflector Subject: Re: [Elecraft] K2/100 power-out change It IS in the software ALC... reflects the ALC's attempting (at about a 1-seconds rate) to 'stabilize the output at the requested pow

Re: [Elecraft] K2/100 power-out change

Rich, Dave, and all, This is 'usual' behavior for the K2 - it seems the power shifts by about 5 watts in high power mode. It is present, but not noticable in low power mode because the shift is only about half a watt which is a smaller percentage of the power setting. Checking the schematic

Re: [Elecraft] K2/100 power-out change

mber 22, 2004 11:23 AM Subject: Re: [Elecraft] K2/100 power-out change Sounds like both K2's I have had. 38xx and 44xx. The output jumps all over the place. My amp does not like it either. When I posted about it, the response I got was that is "normal". Rich - Original M

Re: [Elecraft] K2/100 power-out change

- Original Message - From: Rich McCabe To: Elecraft Reflector Sent: Wednesday, September 22, 2004 11:23 AM Subject: Re: [Elecraft] K2/100 power-out change Sounds like both K2's I have had. 38xx and 44xx. The output jumps all over the place. My amp does not like it either. When I

Re: [Elecraft] K2/100 power-out change

Rich McCabe wrote: Sounds like both K2's I have had. 38xx and 44xx. The output jumps all over the place. My amp does not like it either. When I posted about it, the response I got was that is "normal". See -- 73, Vic, K2VCO Fresno CA http

Re: [Elecraft] K2/100 power-out change

CTED]> To: Sent: Wednesday, September 22, 2004 5:17 AM Subject: [Elecraft] K2/100 power-out change Hi, all concerned: I have two K2/100's (34XX and 37XX) which have 40M c-w-mode power-out variations at a rate of about once a second. For example, if I set 40W out, they will alternate fro

[Elecraft] K2/100 power-out change

Hi, all concerned: I have two K2/100's (34XX and 37XX) which have 40M c-w-mode power-out variations at a rate of about once a second. For example, if I set 40W out, they will alternate from 35 to 40W. It happens on a dummy load, into an antenna, and makes driving an amp interesting ;o) Haven't