Never mind. Found the problem, I was on the 80 band and had turned the
adjustment to get to 7.00 Mhz. Reset to 3500 and used the Band switch and
all is well. "END"
John
NQ3RP
--
View this message in context:
http://elecraft.365791.n2.nabble.com/K2-VFO-Linearization-problem-tp5134647p5134754
I'm to the point of doing the VFO linearization. I went into Cal PLL with
the test probe on TP1, my reading is 12098.8. I enter the Edit portion and
the reading just sits there, never decreasing, never displaying "d" and
never giving me an "end" message. I get no error codes either. Any ideas
Bob,
Have you first checked the PLL range? With the probe in TP3 (you may
have to remove the KDSP2 or KAFT2), and menu in CAL FCTR - what is the
frequency when you tap the BAND+ button? What frequency when you tap
the BAND- button?
If you have a good PLL range, then the frequency should de
K2 #3766, a kit I bought a few years ago and let sit on the shelf for a
while - I'm finally threatening to finish it.
All has gone well up to the "VFO Linearization" step in Alignment where
the CAL PLL menu item is supposed to be run. I've followed the
instructions to the letter, but when I g
K2 #3766, a kit that I bought a few years ago and let sit on the shelf
for a while. I'm finally threatening to finish it. All has gone well
up to the VFO Linearization step in Alignment where the CAL PLL menu
item is supposed to be run. I've followed the instructions to the
letter, but when
Scott,
The K2 looks for a frequency reading near 12,100 kHz when it starts the
CAL PLL sequence.
If yours is only going up to 11,959.64 kHz, that is not high enough.
Info 232 is a usual result if the initial frequency is too low.
Check your PLL reference oscillator range again (check at TP3).
Scott,
Make sure you are tuned between 7.0 and 7.1 Mhz and you are on the right test
point (TP1). It's been a long time since I aligned my K2 but I vaguely remember
making that mistake and getting the same error.
Ron - W2RIP
Scott McDowell <[EMAIL PROTECTED]> wrote:
Hi
I'm tr
Hi
I'm trying to do the vfo linearization on my k2 and am having a problem
again!
Every time I do the cal pll I get the frequency on the counter of 11959.64
for an instant, then the info 232 message about not being on
40 meters. It never goes beyond the info msg. I have entered the frequency
with
Scott McDowell wrote:
The manual says to set the VFO to anywhere between 7000 and 7100 khz. Then
enter the
When I do this I get an info 232 message that says I have to be on 40
meters, which I am on.
Are you on 40m, or is the VFO just set to a frequency in the 40m band?
You can tune ac
Hi
First off, I'm sorry to keep bugging everyone but I have a problem again.
I'm in the VFO linearization part of the second test on my K2, and am having
a problem that the manual doesn't say how to solve.
The manual says to set the VFO to anywhere between 7000 and 7100 khz. Then
enter the
cal pl
To K2 buiders,
I ran the VFO linearization. The frequency displayed was varying between
12,099.00 and 12,098.99 for approximately 13 minutes. Then the frequency
displayed was 12,085.41 ( a difference of 13.59 kHz) followed by d and then
END.
Is this an acceptable linearization? Should ther
11 matches
Mail list logo