Look on Page 11 of the KPA500 Manual
From: mike
To: elecraft@mailman.qth.net
Sent: Tuesday, March 17, 2015 4:10 PM
Subject: Re: [Elecraft] KPA500 suddenly low output - only 30 watts
Nope, not a Null Modem, just a gender changer with the #10 pin clipped (upon
closer inspection
That is the adapter to break the keying line
From: mike
To: elecraft@mailman.qth.net
Sent: Tuesday, March 17, 2015 11:45 AM
Subject: Re: [Elecraft] KPA500 suddenly low output - only 30 watts
Yep, a finicky cable was apparently the problem. I disconnected the two
E850463 AUX cables
Well first of all, Ian, you won the right to yell Woo hoo and the knowledge
that you beat out about three others who figured it out at the same time. Of
course I also figured it out at the same time. Interestingly one fellow
suggested I 'read my manual', which of course I do daily (smile), but I
al
AT500 #860, KPA500 #1468
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of mike
Sent: Tuesday, March 17, 2015 4:32 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KPA500 suddenly low output - only 30 watts
RIGHT! Ian wins the prize. Good for you.
RIGHT! Ian wins the prize. Good for you. 73 ..mike AI6II
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KPA500-suddenly-low-output-only-30-watts-tp7600292p7600407.html
Sent from the Elecraft mailing list archive at Nabble.com.
Wait, it was not KL INT, but KY INT for 'key interrupter'. I think I have it
figured out.
I recently sold my SteppIR vertical which required me to use the PTT Key
line to prevent the amp from keying while the SteppIR was moving. This piece
was used to interrupt the PTT in the AUX cables (missing
, P3 #688, KAT500 #860, KPA500 #1468
-Original Message-
From: Elecraft [mailto:elecraft-boun...@mailman.qth.net] On Behalf Of mike
Sent: Tuesday, March 17, 2015 4:11 PM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] KPA500 suddenly low output - only 30 watts
Nope, not a Null Modem
Nope, not a Null Modem, just a gender changer with the #10 pin clipped (upon
closer inspection.) And I had written on it KL INT or maybe INT KL for which
I have no idea as to the meaning. But no worries it all works great now. ;>)
73 ..mike AI6II
--
View this message in context:
http://elecr
On 3/17/2015 8:45 AM, mike wrote:
> In
> doing so I discovered I had a gender bender on the cable end that plugged
> into the K3. It actually didn't change the gender (the K3 was a female and
> the gender changer was male to female...go figure)
That sounds more like a "null modem" than a "gender
Yep, a finicky cable was apparently the problem. I disconnected the two
E850463 AUX cables (KAT500 to KPA500 and KAT500 to K3 and swapped them, In
doing so I discovered I had a gender bender on the cable end that plugged
into the K3. It actually didn't change the gender (the K3 was a female and
the
Some of those connectors can be a bit finicky, wanting to be snugged up
a little more than common.
Ask me how I know... wiggle, snug, wiggle snug.
Rick NHC
On 3/15/2015 4:04 PM, Jack Brindle wrote:
Mike;
It is definitely a cable problem. If the asterisk is not being displayed on
key-down,
Mike;
It is definitely a cable problem. If the asterisk is not being displayed on
key-down, then the
amplifier is not going to go into transmit. recheck the cables all the way from
the K3 to the KPA
to see what came undone. Find and fix that and the KPA will come back to life.
You might want to
No, the asterisk on the KPA is missing. Nothing appears on the left of the
KPA LCD. I understand that to mean the KPA is not receiving a valid PA KEY
signal. I am using Elecrfat supplied AUX cables from the K3 to the KAT500
and another one from the KAT500 to the KPA.
I did recently change my anten
When you key the K3, does an asterisk show up on the left side of the KPA’s
LCD? If not, check the AUX or PTT connections to the KPA500.
Otherwise, let me know so I can follow up with you to get you going.
- Jack Brindle, W6FB
Elecraft Engineering
> On Mar 15, 2015, at 10:02 AM, mike wrote:
>
] On Behalf Of mike
Sent: Sunday, March 15, 2015 1:02 PM
To: elecraft@mailman.qth.net
Subject: [Elecraft] KPA500 suddenly low output - only 30 watts
I was on a net this morning thinking I had my amp on (it did show OPER),
however I found it was only putting out 30 watts. Moving to STBY I was
putting
I was on a net this morning thinking I had my amp on (it did show OPER),
however I found it was only putting out 30 watts. Moving to STBY I was
putting out 95 watts with the K3 alone, but in OPER the KPA500 only put out
30. My per band setting showed the normal 24 watts (with the asterisk) but
inst
16 matches
Mail list logo