Re: [Emc-users] Tool length probe

I have been thinking about using an old touch probe as a tool setter to measure both z and diameter offset. Anyone had any luck with that so far? I think it would be fancy if I could measure the diameter at the same time as the z offset. My cheap sk40 tool holders have some run out, and using tool

Re: [Emc-users] Cheap vs expensive solar Re: OT: Where's them fires. [Was: Re Conversational mode.

Den mån 11 mars 2019 12:10Erik Christiansen skrev: > On 11.03.19 09:19, Gregg Eshelman via Emc-users wrote: > > This guy in Australia tested a cheap $90 100 watt panel and one that > > cost a lot more. The $90 panel significantly out performed the > > expensive panel.https://www.youtube.com/watch

Re: [Emc-users] Cheap vs expensive solar Re: OT: Where's them fires. [Was: Re Conversational mode.

Den mån 11 mars 2019 12:10Erik Christiansen skrev: > On 11.03.19 09:19, Gregg Eshelman via Emc-users wrote: > > This guy in Australia tested a cheap $90 100 watt panel and one that > > cost a lot more. The $90 panel significantly out performed the > > expensive panel.https://www.youtube.com/watch

Re: [Emc-users] (no subject)

ic level to my 3D printer. But I hope my mill does not have > a 0.1mm tilt. > > Are you able to solder SMDs with out first tinning or solder past. The > milled boards are just plan copper. Do they reflow? I figured I'd use > this technique for 0.1 inch lead parts > > &

Re: [Emc-users] (no subject)

I use KiCAD for schematic and layout. A typical trace would be 0.4mm. The smallest tracers I go is 0.3mm. Anything thinner i the results vary alot. As for SMD's SOT23-6 and SOIC is a comfortable packages to work with. For CAM I use flatcam , with is quite messy at first, but ha

Re: [Emc-users] Finally figured out how to halve an axis!

Thanks Danny! Works like a charm =) /Peter 2017-02-07 7:43 GMT+01:00 Danny Miller : > This has troubled me for awhile. I have the XHC-HB04 pendant. On it is > a "1/2" button. It is very useful when your CNC job uses center datum > and you want to place it in the center of your stock. e.g.

Re: [Emc-users] Can't figure out homing on gantry

Here is the .hal i'm using with the gantry comp. https://forum.linuxcnc.org/forum/47-hal-examples/30818-gantry-hal-example //Peter 2016-08-25 18:10 GMT+02:00 Charles Steinkuehler : > On 8/25/2016 11:00 AM, dan...@austin.rr.com wrote: > > What's that mean? Does it just drive both in tandem unti

Re: [Emc-users] Rookie Question - Direct wire or connectors

ooops bad link Here's abetter example http://www.digikey.com/catalog/en/partgroup/d-1744-series/2069 2015-12-27 12:30 GMT+01:00 Peter Rosenblom : > I use alot of of soldersleavves at work with good result. They are > heatshrinks that has a soldderband inside. you heat them up a

Re: [Emc-users] Rookie Question - Direct wire or connectors

I use alot of of soldersleavves at work with good result. They are heatshrinks that has a soldderband inside. you heat them up as a regular heatshrink, and then kjeep jeating some more until the soldder metlts/wets. Really handy and makes for very good splices. Pare it up with a chemresistand glue-

Re: [Emc-users] That pesky Mach3 1205 BOB

some pictures of how it looks on my setup. /Peter 2015-10-07 17:55 GMT+02:00 Gene Heskett : > On Wednesday 30 September 2015 23:25:05 Gene Heskett wrote: > > > On Wednesday 30 September 2015 12:47:41 Peter Rosenblom wrote: > > > Hi Gene, > > > > > > I got a li

Re: [Emc-users] That pesky Mach3 1205 BOB

Hi Gene, I got a link with the purchace of a bob just like that: http://www.icstation.com/ebay/IC/All%20data%20modules/1849.zip (I havent gotten viruses, but click at your owm risk) A simple schemiatic of the board breakouts in a pdf and some shady mach3 stuff. Hope it helps. /Peter 2015-09-30

Re: [Emc-users] Drag-chain cable

Hmm, yeah you might be right. Shipping to Norway might be a hassle/cost inefficent. Thanks for the ebay tip tough. /Peter 2015-09-15 17:35 GMT+02:00 andy pugh : > On 15 September 2015 at 16:25, Peter Rosenblom wrote: > > > How would we handle payment/shippment? > > Probabl

Re: [Emc-users] Drag-chain cable

Looks tempting. I'm soon gonna need about 5m. How would we handle payment/shippment? /Peter 2015-09-15 16:53 GMT+02:00 andy pugh : > On 15 September 2015 at 15:21, Viesturs Lācis > wrote: > > What is the price? > > I haven't decided yet. Maybe 2 euros a meter? > > -- > atp > If you can't fix i