On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 11:44:07 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject: [Emc-users] hm2_eth driver missing
I just did a fresh pull and compiled from
@lists.sourceforge.net
Sent: 2015-02-26 15:34:08
Subject: Re: [Emc-users] hm2_eth driver missing
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 11:44:07 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC)
emc-users@lists.sourceforge.net
-- Original Message --
From: Peter C. Wallace p...@mesanet.com
To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine
Controller (EMC) emc-users@lists.sourceforge.net
Sent: 2015-02-26 17:13:54
Subject: Re: [Emc-users] hm2_eth driver missing
On Thu, 26 Feb 2015, Marius
-02-26 16:36:34
Subject: Re: [Emc-users] hm2_eth driver missing
You also want to read up on the configuration of the interface\
http://linuxcnc.org/docs/2.7/html/man/man9/hm2_eth.9.html
some more info..
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Uspace
sam
On 2/26/2015 8:26 AM, Marius Liebenberg
; Enhanced Machine
Controller (EMC) emc-users@lists.sourceforge.net
Sent: 2015-02-26 15:34:08
Subject: Re: [Emc-users] hm2_eth driver missing
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 11:44:07 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 15:04:32 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] hm2_eth driver missing
Am I right to say that I cannot run
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 14:26:06 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] hm2_eth driver missing
Thanks Peter, the shebang does it nicely
I just did a fresh pull and compiled from source. There are no hm2_eth
drivers anywhere that I can find. The firmware for 7i80 is not under the
lib/firmware directory either.
How do I go about to get the complete source to build from?
-
Regards / Groete
Marius D.
I am using the Hostmot 2 drivers but are not at the right computer now, I
could check within a few hurs.
I just did a fresh pull and compiled from source. There are no hm2_eth
drivers anywhere that I can find. The firmware for 7i80 is not under the
lib/firmware directory either.
How do I go
the 7i80 is similar to the 5i25 cards in that the firmware isn't loaded
each time - you have to load the using the mesa-flash utility.
(although it comes with a firmware installed - so you should be able to
test)
As far as the driver not being there - are you running rt-preemt
kernel? My
10 matches
Mail list logo